Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND
CAUTIONS. USE THIS PRODUCT CORRECTLY, AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO
MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
1. SAFETY INSTRUCTIONS
1.1
ELECTRICAL SAFETY (Battery Charger)
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
!
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs,
sockets and any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by
the installation of appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the
main distribution board. We also recommend that a Residual Current Device (RCD) is used. It is particularly important
to use an RCD with portable products that are plugged into a supply which is not protected by an RCCB. If in any doubt
consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1 The Electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are
tested by a qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2 The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those
appliances and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified
electrician.
1.1.3 Ensure that the insulation on all cables and on the appliance is safe before
connecting it to the power supply. See 1.1.1 and 1.1.2 and use a Portable
Appliance Tester.
1.1.4 Ensure that cables are always protected against short circuit and overload.
1.1.5 Regularly inspect power supply cables and plugs for wear or damage and check
all connections to ensure that none is loose.
1.1.6 Important: Ensure that the voltage marked on the appliance matches the power
supply to be used and that the plug is fitted with the correct fuse - see fuse rating
at right.
1.1.7 DO NOT pull or carry the appliance by the power cable.
1.1.8 DO NOT pull the plug from the socket by the cable.
1.1.9 DO NOT use worn or damaged cables, plugs or connectors. Immediately have
any faulty item repaired or replaced by a qualified electrician. When a BS 1363/A UK 3 pin plug is damaged, cut the
cable just above the plug and dispose of the plug safely.
Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer
insulation extends beyond the cable restraint and that the restraint is tight. Double insulated products, which are always
marked with this symbol
indicated above - DO NOT connect either wire to the earth terminal.
1.1.10 Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified
electrician to ensure that a suitably rated supply is available. We recommend that you discuss the installation of an
industrial round pin plug and socket with your electrician.
1.1.11 If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since
any appliance plugged into it will be protected. The cable core section is important and should be at least 1.5mm², but
to be absolutely sure that the capacity of the reel is suitable for this product and for others which may be used in the
other output sockets, we recommend the use of 2.5mm² section cable.
1.2
GENERAL SAFETY
WARNING! Disengage the grease gun from the battery before changing accessories, servicing or
!
performing and maintenance.
Maintain gun in good condition (use an authorised service agent).
"
Replace or repair damaged parts. Use recommended parts only. Unauthorised
"
parts may be dangerous and will invalidate the warranty.
Wear appropriate protective clothing. When handling lubricants refer to
"
manufacturer's instructions and conform to local regulations.
Use the gun in a suitable working area. Keep area clean and tidy and free from
"
unrelated materials and ensure there is adequate lighting.
, are fitted with live (brown) and neutral (blue) wires only. To rewire, connect the wires as
INSTRUCTIONS FOR:
CORDLESS GREASE
GUN 12V
CPG12V.V2
MODEL NO:
Yellow & Green
Earth Wire
Blue
Neutral
Wire
FUSE RATING 5 AMP
CPG12V.V2 - 1 - 120607
Brown
Live
Wire
Cable
Restraint
Advertisement
Related Manuals for Sealey CPG12V.V2
Summary of Contents for Sealey CPG12V.V2
- Page 1 CPG12V.V2 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND CAUTIONS.
- Page 2 50mm (2”) and slowly pull the plunger handle out fully (Fig 3). 3.4.4 Screw the grease tube back in to the grease gun. Press the catch plate and release the plunger rod. Push down on the plunger handle. CPG12V.V2 - 1 - 120607...
- Page 3 2002/95/EC RoHS Directive 2002/96/EC WEEE Directive For Jack Sealey Ltd. Sole importer into the UK of Sealey Power Products. NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.