Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instructions
protection
1. SAFETY
1.1.
ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey dealer. If the lamp is used in the course of business duties, it must
be maintained in a safe condition and routinely PAT (Portable Appliance Test) tested. Electrical safety information, it is important that
the following information is read and understood.
1.1.1. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
IMPORTANT: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with
the correct fuse - see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately
8
by a qualified electrician.
1.1.3. This product is fitted with a BS1363/A 13 Amp 3 pin plug. If the cable or plug is damaged during use, switch the electricity supply
and remove from use. Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
IMPORTANT: Class I tool, Class II construction;
A) Connect the BROWN live wire to the live terminal 'L'.
B) Connect the BLUE neutral wire to the neutral terminal 'N'.
C) Connect the GREEN & YELLOW wire to the earth terminal 'E'.
D) After wiring, check that there are no bare wires and ensure that all wires have been correctly connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.
GENERAL SAFETY
WARNING! Ensure that Health & Safety, local authority and general workshop practice regulations
‰
are adhered to when using this sander.
Familiarise yourself with the application, limitations and potential hazards of the sander.
9
WARNING! Disconnect from the mains power and ensure that the pad is at a complete standstill before
‰
changing accessories, servicing or performing any maintenance.
Maintain the sander in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
WARNING! Keep all holding screws in place, tight and in good working order. Check regularly for damaged parts. A part that
‰
is damaged must be repaired/replaced before the sander is next used.
Use the sander in a suitable work area and keep the area clean and tidy and free from unrelated materials.
9
Ensure that there is adequate lighting.
9
Keep the sander clean for best and safest performance.
9
Before each use, check all attachments for condition. If worn or damaged replace immediately.
9
Ensure that there are no flammable materials near the work area.
9
WARNING! Wear approved safety eye protection, ear defenders and, if dust is generated, respiratory protection.
‰
Maintain correct balance and footing. Ensure that the floor is not slippery and wear non-slip shoes.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.
9
Keep children and unauthorised persons away from the work area.
9
Avoid unintentional starting.
9
DO NOT use the sander for any purpose other than that for which it is designed.
8
DO NOT operate the sander if any parts are damaged or missing as this may cause failure and/or personal injury.
8
DO NOT get the sander wet or use in damp or wet locations or areas where there is condensation.
8
DO NOT allow untrained persons to operate the sander.
8
DO NOT operate the sander when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT use the sander where there are flammable liquids, solids or gases such as paint solvents, etc.
8
DO NOT leave the sander operating unattended.
8
DO NOT carry the sander with your finger on the power switch.
8
DO NOT pull the cord from the power supply.
8
Use a qualified person to maintain the sander.
9
When not in use, unplug from the mains power supply and store in a safe, dry, childproof area.
9
© Jack Sealey Limited
ELECTRIC PALM SANDER
Ø150MM VARIABLE SPEED 350W/230V
MODEL NO:
Wear protective
Wear ear
gloves
protection
Original Language Version
DAS150PS
Wear a mask
Recommended fuse rating
5 Amp
DAS150PS | Issue 1 22/08/2019
Advertisement
Related Manuals for Sealey DAS150PS
Summary of Contents for Sealey DAS150PS
- Page 1 Sealey recommend that an RCD (Residual Current Device) is used with all electrical products. You may obtain an RCD by contacting your local Sealey dealer. If the lamp is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance Test) tested.
- Page 2 3. SPECIFICATION Model No: ......DAS150PS Electrical Plug Type:....3-Pin BS Motor Power: .
- Page 3 Have dust extraction unit seen by an authorised service centre emission Sanding sheet not aligned with dust extraction Realign sanding sheet holes in the hook & loop sanding base Extraction holes blocked Unblock dust extraction holes Original Language Version DAS150PS | Issue 1 22/08/2019 © Jack Sealey Limited...
- Page 4 Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk...