Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for RASOR D86P2
Summary of Contents for RASOR D86P2
- Page 1 D86P2 BENCH CUTTER USE MANUAL...
- Page 2 All the parts of the devices have been planned and produced to guarantee an optimum performance. In order to keep the high quality level and the long reliabilty of the Rasor ® products, it is recommended to use only original spare parts and to contact the head...
-
Page 3: General Safety Rules
1. GENERAL SAFETY RULES This manual is an integral part of bench cutter D86P2 and must be carefully read before using it since it gives important indications with regards to its safe installation, use and maintenance. Keep it with care. - Page 4 Moreover, they cannot work in case of rain. In case of damage or malfunction, bench cutter D86P2 must not be used until the Customer Care Technical Service has repaired them.
-
Page 5: Transport And Packing
In such a case, the operator is the only person responsible. Class II double insulation Model Serial number D86P2 220 230 50 60 Electric data Year of production R EAD... -
Page 6: Product Description
4. PRODUCT DESCRIPTION The fixtures described in this manual is a bench cutter model D86P2 which is used in order to cut resistant material. By cutting with the blade and the counterblade always in contact and thanks to the steel upper quality of the blade supplied, D86P2 cutter guarantees the clean separation without frayings of the two borders of the cut material. -
Page 7: Technical Features
The technical data are only indicative and they can be changed without notice. 6. NOISE LEVEL The maximum acoustic pressure level emitted by bench cutter D86P2 is about 60 dB (A). Noise tests have been carried out in compliance with Standard ISO 11202:2010. The device noise levels, measured at different distances (without any sound wave filtering system), vary in the extent of few db (A). -
Page 8: Use Warnings
Always pay attention to the electric cable position to prevent it from being cut or damaged by the blade. It is allowed to assemble bench cutter D86P2 on machines O.E.M. on condition that their original structure is not modified. Otherwise, the intervention must be certified by Rasor ®... -
Page 9: Residual Risks
10. RESIDUAL RISKS Even though the bench cutter is safe, operators must pay attention to preserve their and other people’s safety. At the end of the working operations, the motor could be very hot. The cutting blade can work even when the protective device is disassembled. 11. -
Page 10: Blade Sharpening
To carry out this operation, remove protective plug “A” located on the motor support of the bench cutter and fill it with lubricating grease Rasor. Screw plug “A” again few turns. Screw plug “A” some turns every 2-3 working hours (see picture 10). -
Page 11: Blade Replacement
5) Replace the worn blade with the new one “2”, being careful to center the blade on the gear, in the correct position, and remember to assemble it, so that the Rasor writing can be seen by the operator. 6) Assemble all the components again and carry out... -
Page 12: Troubleshooting
15. TROUBLESHOOTING PROBLEM SOLUTION Check that the blade and the counterblade contact with each other Check the kind of fabric Sharpen the blade The fabric is not cut or it gets stuck between the Check the fabric thickness blade and the counterblade Check the compatibility between blade and fabric Make sure that the motor turns correctly Reduce the feeding speed... - Page 14 The warranty covers all manufacturing and material defects. Replacement and repair operations are covered only if carried out by our company and at our workshop. If in-warranty goods need to be repaired, the customer must always send the complete machine to Rasor ®...
- Page 15 RASOR ELETTROMECCANICA SRL Via Vincenzo Caldesi 6 20161 Milan ∙ Italy ph. +39 02 66 22 12 31 fax +39 02 66 22 12 93 info@rasor-cutters.com www.rasor-cutters.com FOLLOW US:...