Page 1
MAIN LOGIC-1 MAIN-1 MODEL VERSION Bluetooth WX NUMBER Unit Unit Unit Unit USA-01 ‒ ‒ ✔ ✔ ✔ ✔ ✔ IC-A25N EXP-01 ‒ ‒ ✔ ✔ ✔ ✔ ✔ EUR-01 ‒ ‒ ‒ ✔ ✔ ✔ ✔ IC-A25NE AUS-01 ‒...
Page 2
The input signal strength level of this receive sensitivity is measured at the load end (PD). Measurements made in accordance with FCC Part87 (IC-A25N and IC-A25C), or EN300 676 (IC-A25NE and IC-A25CE). All stated specifications are typical and subject to change without notice or obligation.
Page 3
(Replacement page) March 2019 SECTION 4 ADJUSTMENT PROCEDURE The underlined parts have been updated from the previous version of the addendum, or the original page. 4-1 PREPARATION ■ REQUIRED EQUIPMENT EQUIPMENT SPECIFICATIONS EQUIPMENT SPECIFICATIONS Output voltage: 11 V CS-A25 Programming software DC power supply Programming software Current capacity:...
Page 4
(Replacement page) March 2019 The underlined parts have been updated from the previous version of the addendum, or the original page. ■ ENTERING THE ADJUSTMENT MODE 1. Right click the CS-A25's icon on the desktop and select 8. Write the data to the transceiver. the "Properties."...
Page 5
(Replacement page) March 2019 The underlined parts have been updated from the previous version of the addendum, or the original page. ■ KEY ASSIGNMENTS FOR THE ADJUSTMENT ■ WRITE THE CLONING DATA MODE After adjusting, write back save the cloning data. •...
Page 6
(Replacement page) March 2019 The underlined parts have been updated from the previous version of the addendum, or the original page. 4-2 FREQUENCY AND TRANSMIT ADJUSTMENTS 1. Select an adjustment item by pushing [▲]/[▼]. 2. Set or modify the adjustment value as specified by rotating [DIAL], and then push [ENT]. ADJUSTMENT TRANSCEIVER'S ADJUSTMENT...
Page 7
(Replacement page) March 2019 The underlined parts have been updated from the previous version of the addendum, or the original page. 4-2 FREQUENCY AND TRANSMIT ADJUSTMENTS (CONTINUED) 1. Select an adjustment item by pushing [▲]/[▼]. 2. Set or modify the adjustment value as specified by rotating [DIAL], and then push [ENT]. ADJUSTMENT TRANSCEIVER'S ADJUSTMENT...
Page 8
† VOR 0° VOR0 • Frequency: 108.000 MHz Connect the VOR tester to the Push [ENT] • Receiving antenna connector, and set it to: (Automatic (Only for IC-A25N) Frequency: 108.000 MHz adjustment) Level: +47 dBμ (−60 dBm) † Modulation: 30 Hz...
Page 9
(Amended page) March 2019 PARTS LIST The underlined parts have been updated from the previous version of the addendum, or the original page. [LOGIC UNIT] (for #11, #12, #21, #22, and #31) [LOGIC UNIT] (for #11, #12, #21, #22, and #31) PART PART DESCRIPTION...
Page 10
(Amended page) March 2019 The underlined parts have been updated from the previous version of the addendum, or the original page. [LOGIC UNIT] (for #11, #12, #21, #22, and #31) [LOGIC UNIT] (for #11, #12, #21, #22, and #31) PART PART DESCRIPTION DESCRIPTION...
Page 11
(Amended page) March 2019 The underlined parts have been updated from the previous version of the addendum, or the original page. [LOGIC UNIT] (for #11, #12, #21, #22, and #31) [LOGIC UNIT] (for #11, #12, #21, #22, and #31) PART PART DESCRIPTION DESCRIPTION...
Page 12
(Amended page) March 2019 The underlined parts have been updated from the previous version of the addendum, or the original page. [MAIN UNIT] (for #11, #12, #21, #22, and #31) [MAIN UNIT] (for #11, #12, #21, #22, and #31) PART PART DESCRIPTION DESCRIPTION...
Page 13
(Amended page) March 2019 The underlined parts have been updated from the previous version of the addendum, or the original page. [MAIN UNIT] (for #11, #12, #21, #22, and #31) [MAIN UNIT] (for #11, #12, #21, #22, and #31) PART PART DESCRIPTION DESCRIPTION...
Page 14
(Amended page) March 2019 The underlined parts have been updated from the previous version of the addendum, or the original page. [MAIN UNIT] (for #11, #12, #21, #22, and #31) [MAIN UNIT] (for #11, #12, #21, #22, and #31) PART PART DESCRIPTION DESCRIPTION...
Page 15
(Amended page) March 2019 The underlined parts have been updated from the previous version of the addendum, or the original page. [MAIN UNIT] (for #11, #12, #21, #22, and #31) [MAIN UNIT] (for #11, #12, #21, #22, and #31) PART PART DESCRIPTION DESCRIPTION...
Page 16
(Amended page) March 2019 The underlined parts have been updated from the previous version of the addendum, or the original page. [MAIN UNIT] (for #11, #12, #21, #22, and #31) [MAIN UNIT] (for #11, #12, #21, #22, and #31) PART PART DESCRIPTION DESCRIPTION...
Page 17
(Amended page) March 2019 The underlined parts have been updated from the previous version of the addendum, or the original page. [LOGIC-1 UNIT] [LOGIC-1 UNIT] ( for #13, #14, #16, #17, #23, #24, #27, #33, #34, and #36) ( for #13, #14, #16, #17, #23, #24, #27, #33, #34, and #36) PART PART DESCRIPTION...
Page 18
(Amended page) March 2019 The underlined parts have been updated from the previous version of the addendum, or the original page. [LOGIC-1 UNIT] [LOGIC-1 UNIT] ( for #13, #14, #16, #17, #23, #24, #27, #33, #34, and #36) ( for #13, #14, #16, #17, #23, #24, #27, #33, #34, and #36) PART PART DESCRIPTION...
Page 19
(Amended page) March 2019 The underlined parts have been updated from the previous version of the addendum, or the original page. [LOGIC-1 UNIT] [LOGIC-1 UNIT] ( for #13, #14, #16, #17, #23, #24, #27, #33, #34, and #36) ( for #13, #14, #16, #17, #23, #24, #27, #33, #34, and #36) PART PART DESCRIPTION...
Page 20
(Amended page) March 2019 The underlined parts have been updated from the previous version of the addendum, or the original page. [LOGIC-1 UNIT] [LOGIC-1 UNIT] ( for #13, #14, #16, #17, #23, #24, #27, #33, #34, and #36) ( for #13, #14, #16, #17, #23, #24, #27, #33, #34, and #36) PART PART DESCRIPTION...
Page 21
(Amended page) March 2019 The underlined parts have been updated from the previous version of the addendum, or the original page. [LOGIC-1 UNIT] [LOGIC-1 UNIT] ( for #13, #14, #16, #17, #23, #24, #27, #33, #34, and #36) ( for #13, #14, #16, #17, #23, #24, #27, #33, #34, and #36) PART PART DESCRIPTION...
Page 22
(Amended page) March 2019 The underlined parts have been updated from the previous version of the addendum, or the original page. [MAIN-1 UNIT] [MAIN-1 UNIT] ( for #13, #14, #16, #17, #23, #24, #27, #33, #34, and #36) ( for #13, #14, #16, #17, #23, #24, #27, #33, #34, and #36) PART PART DESCRIPTION...
Page 23
(Amended page) March 2019 The underlined parts have been updated from the previous version of the addendum, or the original page. [MAIN-1 UNIT] [MAIN-1 UNIT] ( for #13, #14, #16, #17, #23, #24, #27, #33, #34, and #36) ( for #13, #14, #16, #17, #23, #24, #27, #33, #34, and #36) PART PART DESCRIPTION...
Page 24
(Amended page) March 2019 The underlined parts have been updated from the previous version of the addendum, or the original page. [MAIN-1 UNIT] [MAIN-1 UNIT] ( for #13, #14, #16, #17, #23, #24, #27, #33, #34, and #36) ( for #13, #14, #16, #17, #23, #24, #27, #33, #34, and #36) PART PART DESCRIPTION...
Page 25
(Amended page) March 2019 The underlined parts have been updated from the previous version of the addendum, or the original page. [MAIN-1 UNIT] [MAIN-1 UNIT] ( for #13, #14, #16, #17, #23, #24, #27, #33, #34, and #36) ( for #13, #14, #16, #17, #23, #24, #27, #33, #34, and #36) PART PART DESCRIPTION...
Page 26
(Amended page) March 2019 The underlined parts have been updated from the previous version of the addendum, or the original page. [MAIN-1 UNIT] [MAIN-1 UNIT] ( for #13, #14, #16, #17, #23, #24, #27, #33, #34, and #36) ( for #13, #14, #16, #17, #23, #24, #27, #33, #34, and #36) PART PART DESCRIPTION...
Page 27
(Amended page) March 2019 The underlined parts have been updated from the previous version of the addendum, or the original page. [MAIN-1 UNIT] [MAIN-1 UNIT] ( for #13, #14, #16, #17, #23, #24, #27, #33, #34, and #36) ( for #13, #14, #16, #17, #23, #24, #27, #33, #34, and #36) PART PART DESCRIPTION...
Page 28
(Replacement page) March 2019 SECTION 6 MECHANICAL PARTS The underlined parts have been updated from the previous version of the addendum, or the original page. [CHASSIS UNIT] [CHASSIS UNIT] PART PART DESCRIPTION QTY. DESCRIPTION QTY. 2510002150 C36N07M-7 MP44 8930098420 SPONGE (PK) MP45 8930098420 SPONGE (PK) MP46...
Page 29
(Replacement page) March 2019 The underlined parts have been updated from the previous version of the addendum, or the original page. [LOGIC-1 UNIT] [ACCESSORIES] ( for #13, #14, #16, #17, #23, #24, #27, #33, #34, and #36) PART DESCRIPTION QTY. PART DESCRIPTION QTY.
Page 30
(Replacement page) March 2019 The underlined parts have been updated from the previous version of the addendum, or the original page. MP26 (CHASSIS) MP18 (CHASSIS) (8850003421) (Refere to the parts list.) J1 (CHASSIS) MP12 (CHASSIS) EP1 (CHASSIS) (6510027690) Apply the grease to the following area of the front panel (8930096820) (Refere to the parts list.) MP27 (CHASSIS)
Page 31
(Amended page) March 2019 BOARD LAYOUTS The actual configuration of the PC board can be seen by viewing the top and bottom BOARD LAYOUT pages together. The underlined parts have been updated from the previous version of the addendum, or the original page. •...
Page 32
(Amended page) March 2019 The actual configuration of the PC board can be seen by viewing the top and bottom BOARD LAYOUT pages together. The underlined parts have been updated from the previous version of the addendum, or the original page. •...
Page 33
(Amended page) March 2019 The actual configuration of the PC board can be seen by viewing the top and bottom BOARD LAYOUT pages together. The underlined parts have been updated from the previous version of the addendum, or the original page. •...
Page 34
(Amended page) March 2019 The actual configuration of the PC board can be seen by viewing the top and bottom BOARD LAYOUT pages together. The underlined parts have been updated from the previous version of the addendum, or the original page. •...
Page 35
(Amended page) March 2019 The actual configuration of the PC board can be seen by viewing the top and bottom BOARD LAYOUT pages together. The underlined parts have been updated from the previous version of the addendum, or the original page. •...
Page 36
(Amended page) March 2019 The actual configuration of the PC board can be seen by viewing the top and bottom BOARD LAYOUT pages together. The underlined parts have been updated from the previous version of the addendum, or the original page. •...
Page 37
(Amended page) March 2019 The actual configuration of the PC board can be seen by viewing the top and bottom BOARD LAYOUT pages together. The underlined parts have been updated from the previous version of the addendum, or the original page. •...
Page 38
(Amended page) March 2019 The actual configuration of the PC board can be seen by viewing the top and bottom BOARD LAYOUT pages together. The underlined parts have been updated from the previous version of the addendum, or the original page. •...
Page 39
SERVICE MANUAL VHF AIR BAND TRANSCEIVERS iA25N iA25C iA25NE iA25CE S-15419XZ-C1 December 2017...
Page 40
7. READ the instructions of the test equipment thoroughly before connecting it to the transceiver. Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia, Australia, New Zealand, and/or other countries.
SECTION 2 INSIDE VIEWS • LOGIC/LOGIC-1 UNIT (TOP VIEW) GPS Antenna* BT Regulator* Bluetooth module* (IC30) (IC1) *Only for IC-A25N...
Page 44
• LOGIC/LOGIC-1 UNIT (BOTTOM VIEW) GPS Module (IC17)* † Inside the shield case CPU (IC27) † Under the shield plate Clock Oscillator (X1) † Under the shield plate 5 V Regulator (IC40) (for LCD Backlight) *Only for IC-A25N...
Page 45
† Under the shield plate 2nd IF Filter (FI2: for Wide) Discriminator (X1) D/A Converter (IC216) MIC Switch (IC231) Tx/Rx VCO Circuits D/A Converter (IC220) Audio Volume (IC229) ALC Amplifier (IC215) Internal Microphone (MC1) [DC 11V] (J1) *Only for IC-A25N...
Page 46
• MAIN-A UNIT (BOTTOM VIEW) RF Amplifier (Q11) 1st Mixer (Q12) 1st IF Filter (FI1: for Wide) 1st IF Filter (FI2: for Narrow) 1st IF Amplifier (Q13) IF IC (IC1) Pre-Drive Amplifier Reference Oscillator (Q4) (X203) AM/FM Switch (IC2) PLL IC (IC203) VCO Switch (Q57) Shift Resistor (IC5) Lowpass Filter (IC223)
Remove 2 dial knobs and antenna nut from the Use a suction lifter to lift the bottom of the CHASSIS up. front panel. Inner dial Antenna nut Remove with; Outer dial “ICOM Driver (K)” (8960000112) Suction lifter • Part name: EA950R-2 • Manufacture: ESCO CO.LTD Suction lifter Remove 2 screws from the bottom of chassis.
Page 48
2. REMOVING THE MAIN/-1 UNIT Unsolder 11 points on the shield plate, and then Remove 11 screws from the MAIN/-1 UNIT, and remove it. then remove it from the chassis. Screws×11 UNSOLDER Solder remover Shield plate MAIN/-1 UNIT MAIN/-1 UNIT Chassis Unsolder a point at the antenna connector.
SECTION 4 ADJUSTMENT PROCEDURE 4-1 PREPARATION REqUIRED EqUIPMENT ■ EqUIPMENT SPECIFICATIONS EqUIPMENT SPECIFICATIONS Output voltage: 11 V CS-A25 Programming software DC power supply Programming software Current capacity: 5 A or more (Revision 1.0 or later) Battery pack BP-288 (Fully charged) Programming cable OPC-478UC Measuring range: 0.1~5 W...
Page 50
ENTERING THE ADJUSTMENT MODE ADJUSTMENT MODE SCREEN ■ ■ Right click the CS-A25's icon on the desktop and select the "Properties." • The CS-A25 properties window appears. Append " /Expert" to the end of the contents of the Target field, and then click [OK]. •...
4-2 FREqUENCY AND TRANSMIT ADJUSTMENTS Select an adjustment item by pushing [ Y]/[Z]. Set or modify the adjustment value as specified by rotating [DIAL], and then push [ENT]. ADJUSTMENT ADJUSTMENT TRANSCEIVER'S CONDITION OPERATION VALUE ITEM NAME REFERENCE • Frequency: 136.975 MHz •...
Level: +10 dBμ (−97 dBm) † VOR 0° VOR0 • Frequency: 108.000 MHz Connect the VOR tester to the Push [ENT] (Only for IC-A25N) • Receiving antenna connector, and set as shown (Automatic below: adjustment) Frequency: 108.000 MHz Level: +47 dBμ...
Page 71
MP26 (CHASSIS) EP1 (CHASSIS) (8850003421) (Refere to the parts list.) J1 (CHASSIS) MP12 (CHASSIS) MP18 (CHASSIS) (6510027690) Apply the grease to the following area of the front panel (8930096820) (Refere to the parts list.) Used grease: G501 (80G) SHINETSU (8950002750) MP27 (CHASSIS) MP32 (CHASSIS) (8930098360)
SECTION 7 BOARD LAYOUT The actual configuration of the PC board can be seen by viewing the top and bottom BOARD LAYOUT pages together. • LOGIC UNIT (B-8813: Top view) G-TXD G-RXD • MAIN UNIT (B-8812: Top view) [MIC] [SP] [DC 11 V] CPU3V FINED...
Page 73
The actual configuration of the PC board can be seen by viewing the top and bottom BOARD LAYOUT pages together. [DIAL/VOL] • LOGIC UNIT (B-8813: Bottom view) R862 R861 R1059 C633 • MAIN UNIT (B-8812: Bottom view) R1061 C637 R860 R859 R857 [DC 11 V] (J1)
Page 74
The actual configuration of the PC board can be seen by viewing the top and bottom BOARD LAYOUT pages together. • LOGIC-1 UNIT (B-8816: Top view) G-TXD G-RXD • MAIN UNIT (B-8801a: Top view) CPU3V [MIC] [SP] [DC 11 V] FINED BTRXD BTTXD...
Page 75
The actual configuration of the PC board can be seen by viewing the top and bottom BOARD LAYOUT pages together. [DIAL/VOL] • LOGIC UNIT (B-8813: Bottom view) R862 R861 R1059 C633 • MAIN UNIT (B-8812: Bottom view) R1061 C637 R860 R859 R857 [DC 11 V] (J1)
VORON IC37 VOL_IN R983 R1030 PSTB R981 3.4 V Displayed frequency 108.000~117.975 MHz: 3.3 V GT24C128B 118.000~136.99166 MHz: 0 V R1081 *IC-A25N only EDATA IC38 C682 *Q15 0.068 VOR3.3V VOUT 3.3 V NJU7704F3 LIGHT Displayed frequency 108.000~117.975 MHz: 3.4 V 118.000~136.99166 MHz: 0 V...
Page 78
VOUT Explanatory notes ON: 3.3 V *IC31 OFF: 0 V TX Line GPS Set (in the Menu) *IC-A25N only ON: 3.3 V RX Line OFF: 0 V 5.0 V Voltage Line *IC-A25N only *Refer to the PARTS LIST for the value and name of component.
Page 80
• MAIN UNIT (2/4) PATMP 3.1 V DMC501010 2SB798 • External DC power TX: 10.2 V RX: 0 V • Battery pack TX: 6.8 V RX: 0 V 23.5N 220P 0.001 0.001 52.0N 1SV307 RD12MVS1 R219 RD01MUS2B *R27 3699 3.3k MT3S20P R320 R322...
Page 82
• MAIN UNIT (4/4) 3.0 V 3.3 V 5.0 V 3.0 V EP20 PSTB PSTB 5.0 V 5.0 V PDATA L1SS400 BLM15BD102SN1 PDATA EP19 EP21 UNLK BLM15BD102SN1 UNLK BLM15BD102SN1 R473 EP18 IC238 R604 BLM15BD102SN1 L1SS400 VOUT 100k R469 ON/OFF 100k S-1200B33 RSTN VIN1...
Page 83
VORON IC37 R983 R1030 VOL_IN PSTB R981 3.4 V Displayed frequency 108.000~117.975 MHz: 3.3 V GT24C128B 118.000~136.99166 MHz: 0 V R1081 *IC-A25N only EDATA SKRTLAE010 IC38 C682 *Q15 0.068 VOUT 3.3 V NJU7704F3 SKRTLAE010 LIGHT Displayed frequency 108.000~117.975 MHz: 3.4 V 118.000~136.99166 MHz: 0 V...
Page 84
Explanatory notes VOUT ON: 3.3 V *IC31 OFF: 0 V TX Line GPS Set (in the Menu) *IC-A25N only ON: 3.3 V RX Line OFF: 0 V 5.0 V Voltage Line *IC-A25N only *Refer to the PARTS LIST for the value and name of component.
Page 88
• MAIN-1 UNIT (4/4) 3.0 V 3.3 V 5.0 V 3.0 V EP20 PSTB PSTB 5.0 V 5.0 V PDATA L1SS400 BLM15BD102SN1 PDATA EP19 EP21 UNLK BLM15BD102SN1 UNLK BLM15BD102SN1 EP18 R473 IC238 BLM15BD102SN1 R604 L1SS400 VOUT 100k R469 100k ON/OFF S-1200B33 RSTN VIN1...
Page 89
DISTRIBUTORS ADDRESS If you have any inquiries regarding service, contact your distributor. The contact number or E-mail address of your distributor can be found on our website. http://www.icom.co.jp/world/...