Advertisement
Quick Links
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLease reaD tHese instructions carefuLLy. note tHe safe oPerationaL reQuireMents,
WarninGs anD cautions. use tHis ProDuct correctLy anD WitH care for tHe PurPose for WHicH
it is intenDeD. faiLure to Do so May cause DaMaGe anD/or PersonaL inJury anD WiLL inVaLiDate
tHe Warranty. PLease KeeP instructions safe for future use.
1.
safety instructions
WarninG! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to
when using this equipment.
WarninG! Disconnect from air supply before changing accessories or servicing.
Maintain the sander in good condition (use an authorised service agent).
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will
invalidate the warranty.
Use in suitable clean and tidy working area, free from unrelated materials and ensure there is adequate lighting.
Before each use check abrasive pads for condition. If worn or damaged replace immediately.
Ensure the abrasive pad rating is the same as, or greater than, the RPM rating of the sander.
Ensure there are no flammable or combustible materials near the work area.
WarninG! Always wear approved eye, face and hand protection when operating the sander.
Use dust / respiratory protection in accordance with COSHH regulations.
Depending on the task, sander noise level may exceed 85dB in which case wear safety ear defenders.
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery, and contain and/or tie back long hair.
Wear appropriate protective clothing and keep hands and body clear of working parts.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
Keep children and unauthorised persons away from the working area.
Check moving parts alignment on a regular basis.
Ensure workpiece is secure before operating the sander. Never hold a workpiece by hand.
Check the workpiece to ensure there are no protruding screws, bolts, nuts, nails, stones, etc.
Avoid unintentional starting.
WarninG! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 70-90psi
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
that all connections are secure.
Prolonged exposure to vibration from this sander poses a health risk. It is the owner's responsibility to correctly
assess the potential hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
Do not use the sander for a task it is not designed to perform.
Do not operate sander if any parts are damaged or missing as this may cause failure and/or personal injury.
Do not use cloth backed sanding pads. Use only appropriate paper adhesive pads, following pad instructions.
WarninG! Do not sand any materials containing asbestos.
Do not carry the sander by the hose, or yank the hose from the air supply.
Do not place attachments close to your face and do not point at other persons or animals.
Do not operate sander when you are tired or under the influence of alcohol, drugs or intoxicating medication.
Do not use sander where there are flammable liquids, solids or gases such as paint solvents and
including waste wiping or cleaning rags etc.
Do not attempt to attach a grinding disc to this sander since the machine speed of 18,000 rpm
would cause a disc to shatter.
Do not carry the sander with your finger on the power lever.
Do not direct air from the air hose at yourself or others.
When not in use disconnect from air supply and store in a safe, dry, childproof location.
INStRUCtIONS fOR:
air oPerateD orbitaL
sanDer
MODEl No:
Original Language Version
sa10.V3
SA10.V3
Issue: 1 - 24/02/10
Advertisement
Related Manuals for Sealey SA10.V3
Summary of Contents for Sealey SA10.V3
- Page 1 MODEl No: Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLease reaD tHese instructions carefuLLy. note tHe safe oPerationaL reQuireMents, WarninGs anD cautions.
- Page 2 A quick change coupling may then be used to connect the leader hose to the air line recoil hose. See fig.1 & 2. fig.2 fig.1 Original Language Version SA10.V3 Issue: 1 - 24/02/10...
- Page 3 Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty. lubricate the air saw daily either with a few drops of Sealey air tool oil dripped into the air inlet or via an oiler in the air supply.