Advertisement
Quick Links
thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to
Wear eye
instruction
protection
manual
1. saFetY
1.1.
General saFetY
WarninG! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
‰
WarninG! disconnect from air supply before changing accessories or servicing.
‰
maintain the sander in good condition (use an authorised service agent).
9
replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
use in a suitable clean and tidy work area and ensure there is adequate lighting.
9
Before each use check abrasive pads for condition. if worn or damaged replace immediately.
9
ensure the abrasive pad rating is the same as, or, greater than the rPm rating of the sander.
9
ensure there are no flammable or combustible materials near the work area.
9
WarninG! Always wear approved eye or face and hand protection when operating the sander.
‰
use face, dust, or respiratory protection in accordance with cosHH regulations.
9
depending on the task, sander noise level may exceed 85dB, in which case wear safety ear defenders.
9
remove ill fitting clothing. remove ties, watches, rings, other loose jewellery and contain and/or tie back long hair.
9
maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the work area.
9
check moving parts alignment on a regular basis.
9
ensure workpiece is secure before operating the sander. never hold a workpiece by hand.
9
check the workpiece to ensure there are no protruding screws, bolts, nuts, nails, stones, etc.
9
Avoid unintentional starting.
9
WarninG! ensure correct air pressure is maintained and not exceeded. recommended pressure 70-90psi.
‰
Keep air hose away from heat, oil and sharp edges. check air hose for wear before each use and ensure that all connections are
9
secure.
Prolonged exposure to vibration from this sander poses a health risk. it is the owner's responsibility to correctly assess the potential
9
hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
do not use the sander for a task it is not designed to perform.
8
do not operate sander if any parts are damaged or missing as this may cause failure and/or personal injury.
8
WarninG! do not sand any materials containing asbestos.
‰
do not carry the sander by the hose, or yank the hose from the air supply.
8
do not force, or apply heavy pressure to the sander, let the sander do the work.
8
do not place air line attachments close to your face and do not point at other persons or animals.
8
do not operate sander when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
do not use sander where there are flammable liquids, solids or gases such as paint solvents and including waste wiping or cleaning
8
rags etc.
do not carry the sander with your finger on the power lever.
8
do not direct air from the air hose at yourself or others.
8
When not in use disconnect from air supply and store in a safe, dry, childproof location.
9
1.2.
lead Paint WarninG!
Paint once contained lead as a traditional ingredient. the dust caused by the removal of such paint is toxic and must therefore be
avoided. the following action must be taken before using the sander on a surface that you suspect may contain lead paint.
1. user must determine potential hazard relating to age of paint to be removed (modern paints do not have lead content).
2. danGer! Keep all persons and pets away from the working area. the following are particularly vulnerable to the effects of lead paint
dust: Pregnant women, babies and children.
3. We recommend personal protection by using the following safety items:
a) Paint spray respirator (our ref ssP16en)
b) Pe coated Hooded coverall (our ref ssP267). c) latex Gloves (our ref ssP24).
4. take adequate measures to contain the paint dust, flakes and scrapings.
5. continue to wear safety equipment as in (3) and thoroughly clean all areas when task is complete.
6. ensure paint waste is disposed of in sealed bags or containers.
© Jack sealey limited
instructions for
air orbital sander mini disc Ø50mm
model no:
Wear ear
Wear
protection
protective
gloves
Original Language Version
Gsa70
Wear
a mask
GsA70 | issue:3 (l) 21/09/17
Advertisement
Related Manuals for Sealey GSA70
Summary of Contents for Sealey GSA70
- Page 1 Gsa70 model no: thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty. 6.1. if the air supply does not have an oiler lubricate the air sander daily with a few drops of good grade air tool oil such as sealey Ato/500 or Ato/1000, dripped into the air inlet before use.
- Page 3 Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. sealey Group, Kempson Way, suffolk business Park, bury st edmunds, suffolk. iP32 7ar 01284 757500 01284 703534 sales@sealey.co.uk...