Table of Contents
Advertisement
Power Clear
Model No. 38754—Serial No. 400000000 and Up
Introduction
This machine is intended to be used by residential
homeowners. It is designed primarily for removing
snow from paved surfaces, such as driveways and
sidewalks, and other surfaces for traffic on residential
or commercial properties. It is not designed for
removing materials other than snow, nor is it designed
for clearing gravel surfaces. Using this product for
purposes other than its intended use could prove
dangerous to you and bystanders.
Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. You are responsible for
operating the product properly and safely.
Visit www.Toro.com for product safety and operation
training materials, accessory information, help finding
a dealer, or to register your product.
Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model
and serial numbers of your product ready.
identifies the location of the model and serial numbers
on the product. Write the numbers in the space
provided.
Important:
With your mobile device, you can
scan the QR code on the serial number decal (if
equipped) to access warranty, parts, and other
product information.
1. Model and serial number location
© 2018—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
721 R-C Commercial Snowthrower
Figure 1
Figure 1
Register at www.Toro.com.
Model No.
Serial No.
This manual identifies potential hazards and has
safety messages identified by the safety-alert symbol
(Figure
2), which signals a hazard that may cause
serious injury or death if you do not follow the
recommended precautions.
This manual uses 2 words to highlight information.
Important calls attention to special mechanical
information and Note emphasizes general information
worthy of special attention.
Important:
If you are using this machine above
1500 m (5,000 ft) for a continuous period, ensure
that the High Altitude Kit has been installed
so that the engine meets CARB/EPA emission
regulations. The High Altitude Kit increases
engine performance while preventing spark-plug
fouling, hard starting, and increased emissions.
Once you have installed the kit, attach the
high-altitude label next to the serial decal on the
machine. Contact any Authorized Toro Service
Dealer to obtain the proper High Altitude Kit and
high-altitude label for your machine. To locate
a dealer convenient to you, access our website
at www.Toro.com or contact our Toro Customer
Care Department at the number(s) listed in your
Emission Control Warranty Statement. Remove
the kit from the engine and restore the engine to
its original factory configuration when running the
engine under 1500 m (5,000 ft). Do not operate an
engine that has been converted for high-altitude
use at lower altitudes; otherwise, you could
overheat and damage the engine.
g291503
If you are unsure whether or not your machine has
been converted for high-altitude use, look for the
following label
Original Instructions (EN)
Form No. 3428-994 Rev A
Operator's Manual
Figure 2
Safety-alert symbol
(Figure
3).
All Rights Reserved *3428-994* A
Printed in Mexico
g000502
Advertisement
Table of Contents
Related Manuals for Toro Power Clear 721 R-C
Summary of Contents for Toro Power Clear 721 R-C
-
Page 1: Introduction
Whenever you need service, genuine Toro parts, or information and Note emphasizes general information additional information, contact an Authorized Service worthy of special attention. Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 Important:... -
Page 2: Table Of Contents
Contents Introduction ............... 1 Safety ............... 3 General Safety ........... 3 Safety and Instructional Decals ......4 decal127-9363 Setup ................ 5 Figure 3 1 Unfolding the Handle ........5 2 Installing the Recoil-Start Guide and Rope ............... 5 3 Installing the Discharge Chute ......5 WARNING 4 Filling the Engine with Oil ......... -
Page 3: Safety
Safety This machine has been designed in accordance with ANSI/OPEI B71.3 specifications. General Safety This product is capable of amputating hands and feet and of throwing objects. Always follow all safety instructions to avoid serious personal injury. • Read and understand the contents of this Operator’s Manual before you start the engine. -
Page 4: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal133-8061 133-8061 decal94-2577 94-2577 1. To engage the rotor blades, hold the control bar against the handle. -
Page 5: Setup
Setup Unfolding the Handle No Parts Required Procedure g287662 Installing the Recoil-Start Guide and Rope No Parts Required Procedure g286483... -
Page 6: Installing The Discharge Chute
Installing the Discharge Chute No Parts Required Procedure g287665 Filling the Engine with Oil No Parts Required Procedure g286445... -
Page 7: Adjusting The Control Cable
Adjusting the Control Cable No Parts Required Procedure Refer to Adjusting the Control Cable (page 15). -
Page 8: Product Overview
Contact your Authorized Service Dealer or authorized Toro distributor or go to www.Toro.com for a list of all approved attachments and accessories. To ensure optimum performance and continued safety certification of the machine, use only genuine Toro replacement parts and accessories. -
Page 9: Operation
Filling the Fuel Tank Operation • For best results, use only clean, fresh (less than Note: Determine the left and right sides of the 30 days old), unleaded gasoline with an octane machine from the normal operating position. rating of 87 or higher ((R+M)/2 rating method). •... -
Page 10: Checking The Engine-Oil Level
Checking the Engine-Oil Level Service Interval: Before each use or daily—Check the engine-oil level and add oil if necessary. g293393 Figure 11... -
Page 11: During Operation
During Operation • Look behind and use care when backing up the machine. • When not actively clearing snow, disengage power During Operation Safety to the auger. • Exercise extreme caution when operating the machine on walks or roads. Stay alert for hidden General Safety hazards or traffic. -
Page 12: Engaging The Rotor Blades
Engaging the Rotor Blades Shutting Off the Engine To engage the rotor blades, hold the control bar To shut off the engine, remove the key from the against the handle (Figure 13). ignition. Adjusting the Discharge Chute and Chute Deflector To raise or lower the angle of the chute deflector, press the trigger on the chute deflector and move the chute deflector up or down. -
Page 13: Clearing A Clogged Discharge Chute
Clearing a Clogged After Operation Discharge Chute After Operation Safety To clear the chute: • Shut the engine off! General Safety • Wait 10 seconds to ensure that the rotor blades have stopped rotating. • Never store the machine with fuel in the fuel tank inside a building where ignition sources are •... -
Page 14: Maintenance
• Do not change the governor settings on the engine. Note: Ensure that a 2 to 3 mm (1/16 to 1/8 inch) Purchase only genuine Toro replacement parts gap exists between the control bar and the handle and accessories. (Figure 16). -
Page 15: Inspecting The Rotor Blades
Adjusting the Control Cable Slide up the spring cover and unhook the spring from the adjuster link (Figure 17). g006587 Figure 18 1. Remove the upper end of 3. Pivot point spring from this hole. 2. Insert the upper end of 4. -
Page 16: Changing The Engine Oil
Changing the Engine Oil Service Interval: After the first 2 hours Yearly If possible, run the engine for a few minutes before changing the oil to warm it. Warm oil flows better and carries more contaminants. Engine Oil Specifications Engine oil capacity 0.6 L (20 fl oz)* g006316 Figure 21... -
Page 17: Replacing The Spark Plug
Replacing the spark plug while the engine is hot can result in burns. Wait until the engine is cool to replace the spark plug. Use a Toro spark plug or equivalent (Champion® g006374 Figure 23 RN9YC or NGK BPR6ES). Remove the boot (Figure 24). -
Page 18: Replacing The Drive Belt
Replacing the Drive Belt Note: Route the new drive belt first around the engine pulley, then the idler pulley, and finally If the drive belt becomes worn, oil-soaked, excessively around the loose rotor pulley positioned just above the rotor shaft (Figure 26). -
Page 19: Storage
Storage With the key removed, pull the recoil-start handle slowly to distribute the oil on the inside of the cylinder. Storage Safety Clean the machine. • Shut off the engine, remove the key, and wait Touch up chipped surfaces with paint available for all movement to stop before you leave the from an Authorized Service Dealer. - Page 20 While the exposure from Toro products may be negligible or well within the “no significant risk” range, out of an abundance of caution, Toro has elected to provide the Prop 65 warnings. Moreover, if Toro does not provide these warnings, it could be sued by the State of California or by private parties seeking to enforce Prop 65 and subject to substantial penalties.