Advertisement
Quick Links
Your new Jack is produced and manufactured to a high standard of dependability and will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
Important: REAd ThESE iNSTRuCTiONS CAREfuLLY. NOTE ThE SAfE OPERATiONAL REQuiREMENTS, WARNiNGS ANd CAuTiONS. uSE
ThiS JACK CORRECTLY ANd WiTh CARE fOR ThE PuRPOSE fOR WhiCh iT iS iNTENdEd. fAiLuRE TO dO SO MAY CAuSE dAMAGE ANd/
OR PERSONAL iNJuRY ANd WiLL iNvALidATE ThE WARRANTY. RETAiN ThESE iNSTRuCTiONS fOR fuTuRE uSE.
1. SAfETY PRECAuTiONS
Ensure the jack is in sound condition and good working order.
Take action for immediate repair or replacement of damaged
parts. Use genuine parts only. The use of improper parts may be
dangerous and will invalidate the warranty.
locate the jack in a suitable, well lit working area.
Keep working area clean and tidy and free from unrelated
materials.
Use jack on level and solid ground, preferably concrete.
Avoid tarmacadam as jack may sink in.
chock wheels of vehicle.
Ensure the vehicle handbrake is engaged, engine is switched off
and transmission is in gear (or "PArK" if automatic).
Ensure minimum distance of 0.5m between vehicle and static
objects such as doors, walls, etc., to allow for vehicle tilting.
Ensure all non-essential persons keep a safe distance whilst the
jack is in use.
Ensure there are no passengers in the vehicle.
Place jack under only those lifting points recommended by
vehicle manufacturer (see vehicle handbook).
check that the lifting point is stable and centred on the jack
saddle.
Ensure the jack wheels are free to move and that there are no
obstructions.
DanGEr: Use the jack for lifting only, not for supporting the
lifted load.
Ensure there are no persons or obstructions beneath the vehicle
before lowering.
Use suitable axle stands under the vehicle before proceeding with
any task.
Use a qualified person to lubricate and maintain the jack.
Ensure that only hydraulic jack oil is used during maintenance.
dO NOT operate the jack if damaged.
dO NOT allow untrained persons to operate the jack.
dO NOT exceed the rated capacity of the jack.
dO NOT allow the vehicle to move during jacking, or use the jack
to move the vehicle.
dO NOT jack vehicle if there is a risk of spillage of fuel, battery
acid, or other dangerous substances.
dO NOT work under the vehicle until axle stands have been
correctly positioned.
dO NOT use the jack for purposes other than that for which it is
intended.
dO NOT top up hydraulic system with brake fluid. Use hydraulic
jack oil only.
dO NOT adjust the safety overload valve.
When not in use store jack, fully lowered, in a safe, dry, childproof
area.
2. iNTROduCTiON / SPECifiCATiON
Made primarily for the motor racing enthusiast, this jack weighs in at
just 17.5kg. The jack utilises many weight-saving techniques such as
a skeletal lift arm and single roller load wheel. lifting bars are fitted
either side of the anodised aluminium chassis enabling fast,
lightweight pick-up.
Model No: ...................................... RJA1450
capacity .......................................... 1.5 tonne
Minimum saddle height ................... 98mm
Maximum saddle height .................. 455mm
Maximum frame height ................... 155mm
length ............................................. 600mm
Weight ............................................. 17.5kg
InsTrUcTIons For:
TROLLEY JACK 1.5 TONNE
ALuMiNiuM ROCKET LifT
ModEl no:
3.
ASSEMBLY
3.1
ASSEMBLY
3.1.1
The jack comprises the following parts:
Aluminium chassis.
Two-part pumping handle.
3.1.2
Insert the upper handle into the lower handle. The spring
loaded locking pin will lock the two pieces together (Fig.1).
3.1.3
Undo the handle socket screw (A) until it no longer
protrudes into the handle socket (Fig.2).
3.1.4
Insert the pump handle into the handle socket hole,
engaging the square drive of the release valve.
3.1.5
Ensure that the handle is correctly inserted into the socket,
then tighten the handle socket screw.
4.
hYdRAuLiC / AiR SYSTEM PuRGiNG
4.1
open the release valve by turning it one full turn
counter-clockwise.
4.2
Pump the handle a minimum eight full strokes.
4.3
close the release valve by turning it clockwise.
fig.3
Original Language Version
RJA1450
fig.1
A
fig.2
rJA1450
Issue: 1 - 16/11/09
Advertisement
Related Manuals for Sealey RJA1450
Summary of Contents for Sealey RJA1450
- Page 1 Model No: ........RJA1450 capacity .......... 1.5 tonne Minimum saddle height ....98mm Maximum saddle height ....455mm Maximum frame height ....
- Page 2 WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. iNfORMATiON: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode. Sole uK distributor, Sealey Group, www.sealey.co.uk...