Page 1
Self Diagnosis Supported model SERVICE MANUAL BG-3S CHASSIS MODEL COMMANDER DEST. CHASSIS NO. MODEL COMMANDER DEST. CHASSIS NO. KV-XF29M35 RM-954 SCC-U24A-A KV-XF29M63 RM-954 India SCC-U22A-A KV-XF29M93 RM-954 India SCC-U22B-A TRINITRON COLOR TV ®...
Page 2
CARBON PAINTED ON THE CRT, AFTER REMOVING THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE ANODE. THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. – 2 –...
KV-XF29M35/XF29M63/XF29M93 RM-954 TABLE OF CONTENTS Section Title Page Section Title Page SELF DIAGNOSIS FUNCTION 5. DIAGRAMS ........ 4 5-1. Block Diagram ............43 1. GENERAL ................ 8 5-2. Frame Schematic Diagram ........46 Circuit Boards Location .......... 49 2. DISASSEMBLY 5-4.
Page 4
KV-XF29M35/XF29M63/XF29M93 RM-954 SELF DIAGNOSTIC FUNCTION The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY/TIMER lamp will automatically begin to flash. The number of times the lamp flashes translates to a probable source of the problem. A definition of the STANDBY/TIMER lamp flash indicators is listed in the instruction manual for the user’s knowledge and reference.
Page 5
KV-XF29M35/XF29M63/XF29M93 RM-954 DISPLAY OF STANDBY/TIMER LIGHT FLASH COUNT 2 times 5 times Lamp ON 0.3 sec. Lamp OFF 3 sec. Lamp OFF 0.3 sec. STANDBY/SLEEP lamp Diagnostic Item Flash Count* +B overcurrent/overvoltage 2 times Vertical deflection stopped White balance failure 5 times * One flash count is not used for self-diagnostic.
Page 6
KV-XF29M35/XF29M63/XF29M93 RM-954 SELF-DIAGNOSTIC SCREEN DISPLAY For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it is possible to bring up past occurances of failure for confirmation on the screen: [To Bring Up Screen Test] In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below: [Screen display] / channel [5] / Sound volume [-] / Power ON...
Page 7
KV-XF29M35/XF29M63/XF29M93 RM-954 SELF-DIAGNOSTIC CIRCUIT IC301 IC001 IC003 Y/CHROMA JUNGLE SYSTEM MEMORY FROM IK-IN IO-8DAT B-DAT FROM [+B] Q604 C O-LED PROTECT IO-SDAT [V] Q509/507 [+B overcurrent ªOCPº] Occurs when an overcurrent on the +B(135) line is detected by Q604. If Q604 go to ON and the voltage to pin 18 of IC301 should go down when V.SYNC is more than seven...
Page 8
SECTION 1 The operating instructions mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers of GENERAL the Operating Instruction Manual remain as in the manual. Using Your New TV WARNING • Dangerously high voltages are present inside the TV. Getting Started •...
Page 9
Connecting the 3D WOOFER Notes • If you connect a monaural VCR, connect the yellow plug to (the yellow jack) and the black plug to -L (MONO) (the white jack). • If you connect a VCR to the ˘ (antenna) terminal, preset the signal You can enjoy high quality sound by connecting the 3D WOOFER.
Page 10
Connecting optional components Securing the TV You can connect optional audio/video components, such as a VCR, multi disc player, To prevent the TV from falling, secure the TV using one of the following methods: camcorder, video game or stereo system. To watch the picture of the connected equipment, see page 10.
Page 11
Watching the TV Watching the TV (continued) ¤ Additional tasks This section explains functions used Do this … while watching TV. Most operations can be done using the remote. Turn off temporarily Press u. The u indicator on the TV lights up red. Turn off completely Press U on the TV.
Page 12
Advanced Operations Selecting the Setting the Wake Up timer SOUND picture and sound MODE SURROUND FAVORITE SOUND MODE PIC MODE MENU Press until the modes PIC MODE WAKE UP TIMER:10M desired period of time ENTER After 10 minutes appears. You can select picture and sound modes and adjust the setting to your preference in PERSONAL option.
Page 13
Viewing your Listening with favorite channels surround sound SOUND MODE SURROUND FAVORITE SURROUND MENU PIC MODE Number buttons ENTER You can display and select six of your The surround feature enables you to favorite channels directly from your TV enjoy the sound effects of a concert hall -/-- screen.
Page 14
You can enjoy stereo sound or bilingual programs of NICAM and A2 (German) stereo systems. A2 (German) bilingual MAIN (Main sound) (Sub sound) Receiving area for NICAM and A2 (German) programs (For KV-XF29M35 only) Press A/B repeatedly System Receiving area until you receive the STEREO sound you want.
Page 15
Viewing Teletext Viewing Teletext (continued) (KV-XF29M35 only) Additional Teletext tasks … Do this TV stations broadcast an information Press service called Teletext via some TV display a Teletext page on the TV picture Each time you press , the screen changes as channels.
Page 16
Select the color system. AUTOnPALnSECAMnNTSC3.58nNTSC4.43 Front of TV * The BBE is manufactured by Sony Corporation under license from BBE Sound, Inc. It is covered by U.S. Patent No. 4,638,258 and No. 4,482,866. PROGR The word “BBE” and the BBE symbol are the trademarks of BBE Sound, ONE-PUSH AUTOMATIC PROGRAMMING Inc.
Page 17
Changing the A/V Changing the A/V CONTROL setting (continued) SOUND MODE SURROUND FAVORITE CONTROL setting Adjusting the ADJUST options under PICTURE MODE PIC MODE MENU MENU ENTER + / – /ENTER Press + or – to select the ENTER The A/V CONTROL menu allows you desired item (e.g., COLOR), to change the picture and sound then press ENTER.
Page 18
Changing the SET Changing the SET UP setting (continued) UP setting Using the CHILD LOCK feature Number buttons You can prevent your children from watching certain programs by The SET UP menu allows you to change using the CHILD LOCK feature. the menu language, lock channels, -/-- adjust the picture position, program...
Page 19
(2) Press + or – until the Press MENU. program number you ENTER Note (KV-XF29M35 only) want to preset (e.g., • You can change the menu language as well as the on-screen language program number 10) between English and Chinese.
Page 20
Changing the Channel Preset (CH PRESET) setting (continued) If you are not satisfied Select the desired with the picture and channel. sound quality, you may (1) Press + or – to select ENTER improve them by using either VHF LOW, VHF fine tuning.
“OFF”, then press ENTER. Press U (main power) to turn off your TV. Inform your nearest Sony service center about the number of times the • For details on the menu system and how to use the menu, refer to u indicator flashes.
Page 22
Troubleshooting (continued) If you find any problem while viewing your TV, please check the following guide. If Symptom Solutions Possible cause any problem persists, contact your Sony dealer . ¸ Good picture • Press + to increase the volume level.
Page 23
(page 28) external sources, e.g., TV screen. heavy machineries, nearby (headphone) jack broadcast station. • Contact your nearest Sony service • Your TV may need service. indicator on your center. TV flashes red a number of times between 3 second intervals.
2-5. F BRACKET REMOVAL 2-7. REPLACEMENT OF PARTS For replacement of the Control Button and Light Guide, unscrew them, exchange 4 Two screws (+BVTP 3 × 12) with the new parts, and fix them with screws (+BVTP) respectively. 5 F bracket 2-7-1.
2-12. H3 BOARD REMOVAL 2-14. PICTURE TUBE REMOVAL NOTE : The picture tube for OCE model is upside-down, and the position for the 6 One screw (+BVTP 3 × 12 with washer) anode-cap and tension spring is changed accordingly. !¡ Four DGC clip 3 Two connectors !™...
Page 29
• REMOVAL OF ANODE-CAP NOTE : After removing the anode, short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield or carbon paint on the CRT. • REMOVING PROCEDURES 1 Turn up one side of the rubber cap in the direction indicated by the arrow a. 2 Using a thumb pull up the rubber cap firmly in the direction indicated by the arrow b.
KV-XF29M35/XF29M63/XF29M93 SECTION 3 RM-954 SET-UP ADJUSTMENTS • The following adjustments should be made when a complete Perform the adjustments in the following order : realignment is required or a new picture tube is installed. 1. Beam Landing • These adjustments should be performed with rated power 2.
KV-XF29M35/XF29M63/XF29M93 RM-954 3-2. CONVERGENCE Preparation : • Before starting this adjustment, adjust the focus, horizontal size and vertical size. • Minimize the brightness setting. Purity • Provide dot pattern. BMC (Hexapole) (1) Horizontal and Vertical Static Convergence Purity Center dot V.
Page 32
KV-XF29M35/XF29M63/XF29M93 RM-954 BMC (Hexapole) Magnet. Blue Neck assy Neck assy If the red, green and blue dots are not balanced or aligned, then use the BMC magnet to adjust in the manner described below. Blue VM board VM board Note 1.
KV-XF29M35/XF29M63/XF29M93 RM-954 Rotate TLV-2 VOL (29”, 34”) on DY 3-3. FOCUS ADJUSTMENT Rotate TLV VOL (25”) on DY Adjust FOCUS control on the flyback transformer for the best XCV Rotate XCV Adj core on DY focus. YCH Rotate YCH VOL on DY...
KV-XF29M35/XF29M63/XF29M93 RM-954 2. WHITE BALANCE ADJUSTMENT 3-4. G2 (SCREEN) AND WHITE BALANCE 1) Set to Service Mode (Refer Section 4-1: ADJUSTMENTS ADJUSTMENTS WITH COMMANDER). 1. G2 (SCREEN) ADJUSTMENT 2) Input white raster signal. 1) Set the PICTURE to normal. 3) Set the PICTURE to minimum.
KV-XF29M35/XF29M63/XF29M93 SECTION 4 RM-954 CIRCUIT ADJUSTMENTS 4-1. ADJUSTMENTS WITH COMMANDER Service adjustments are made with the RM-954 that comes with this unit. 1, 4 Select the adjustment item. ↓ a. ENTERING SERVICE MODE 3, 6 Raise/lower the data value. With the unit on standby ↓...
KV-XF29M35/XF29M63/XF29M93 RM-954 4-2. ADJUSTMENT METHOD Item Number 00 of device GEO Use the same method for all Items. Use 1 and 4 to select the This explanation uses H-Position as an example. 1. Select “GEO 00 HPS” with the 1 and 4 buttons.
Page 37
Adjustment Item Table Device Functionality Note Data Range Function Note for Register Slava RAM Address Name Name Different Data No. (bit) Address (bit) H Position 50/60HZ 12 (7-2) CXA2130S(88H) 96 (7-2) H Size 50/60HZ 11 (7-2) 95 (7-2) Pin Amp 50/60HZ 13 (7-2) 97 (7-2)
Page 38
Adjustment Item Table Device Functionality Note Data Range Function Note for Register Slava RAM Address Name Name Different Data No. (bit) Address (bit) H Drive Pulse Width Switch 00 (6) 54 (6) AFC Gain Control TV/Video 0F (1-0) A1 (1-0) H Oscillation 0C (7-4) 60 (7-4)
Page 39
Adjustment Item Table Device Functionality Note Data Range Function Note for Register Slava RAM Address Name Name Different Data No. (bit) Address (bit) SECAM BELL f0 1C (7-2) CXA2060AS(8AH) 85 (7-2) H Oscillation 0C (7-4) 80 (7-4) Sub Hue Control 05 (7-2) Sub Color Control 04 (7-2)
When replacing IC003 (MEMORY), be sure to change IC001 (µ- COM) to the following new IC at the same time. IC001(µ-CON): VB1 VB2 VB3 VB4 CXP86461-608S (KV-XF29M35) VB2 = VB3 = VB4 CXP86461-602S (KV-XF29M63/XF29M93) 1. Enter to Service Mode. SUB HUE ADJUSTMENT 2.
5-3. CIRCUIT BOARDS LOCATION 5-4. SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS Note: • All capacitors are in µF unless otherwise noted. • All electrolytic capacitors are rated at 50V unless otherwise noted. • All resistors are in ohms. kΩ = 1000Ω, MΩ = 1000kΩ •...
(1) Schematic Diagram of A Board (1/2) CN204 CN203 CN102 TO B3 BOARD CN1405 TO H3 BOARD CN201 :BTOB TO B3 BOARD CN3603 CN608 CN1407 CN303 CN106 CN101 :S-MICRO CN105 CN104 :S-MICRO TO B3 BOARD CN205 CN302 TO B3 BOARD TO B3 BOARD :MINI CN1406...
Page 47
(2) Schematic Diagram of A (2/2) Board CN507 R501 :S-MICRO NS ROT :CHIP TO C BOARD NS MUTE R500 CN1801 135V 135V R596 135V 135V 135V 135V 135V 135V POWER SUPPLY,HV,MICON 135V L516 R502 L517 C500 R544 L515 3W :RS :DCC NS ROT C514...
Page 48
(3) Schematic Diagram of B Board A BOARD N OT E : The circuit indicated at left contains high voltage of over D004 [COMB FILTER] [POWER SUPPLY, HV, MICON, Y/C JUNGLE] D615 D005 600 Vp-p. Please pay attention when inspecting or repair- D616 IC001 B-10...
Page 49
(4) Schematic Diagrams of H and VM Boards TO B3 BOARD TO B3 BOARD TO A BOARD TO SP TO J2 BOARD TO B3 BOARD TO A BOARD TO F BOARD TO A BOARD CN6204 CN6202 CN904 CN3451 CN1400 CN104 CN4602 CN5901 CN601...
Page 50
(5) Schematic Diagram of B Board CN1400 TU1401 :S-MICRO C1461 R1411 C1460 D1415 470p :CHIP AUDIO(R) CH:CHIP F:CHIP UDZSTE-179.1B R/L/Y/S/C/CV R3272 6.8k R IN :CHIP R1420 C1450 C1453 R1412 R1409 C1462 JR1409 R1474 220k F:CHIP :CHIP JW1481 C1437 C1463 :CHIP R3211 L IN AUDIO(L)
BOARD IC3201 NJM2187L PRINTED WIRING BOARD Lch out Lch in [AUDIO PROSESSOR, AV SWITCH] BYPASS FIL 1 3D–STEREO Rch in Rch out SPACE VR 3D–STEREO BYPASS CENTER VR FIL 2 – B Board – Schematic diagram board...
Page 52
(6) Schematic Diagram of F Board C BOARD IC701 STV5112 BLUE FEEDBACK (RED FEEDBACK, GREEN FEEDBACK) (CISPR) BLUE OUTPUT CN4601 T4602 F4601 (RED OUTPUT, VDR461 JW4603 250V GREEN OUTPUT) T4601 :FUSE AC IN AC OUT JW4604 R4601 AC IN AC OUT 1/2W BLUE CATHODE CN4602...
SECTION 6 EXPLODED VIEWS NOTE: • • Items marked " ∗ " are not stocked since Items with no part number and no The components identified by description are not stocked because they are seldom required for routine shading and mark ! are critical they are seldom required for routine ser vice.
Page 56
KV-XF29M35/XF29M63/XF29M93 SECTION 6 RM-954 EXPLODED VIEWS NOTE: • • Items marked " ∗ " are not stocked since Items with no part number and no The components identified by description are not stocked because they are seldom required for routine...
Page 63
IC CXP86461-602S (KV-XF29M63/XF29M93) L905 1-414-856-11 INDUCTOR 10UH IC002 8-759-371-21 IC MM1319AFBE IC003 8-759-370-34 IC ST24C08FB6 IC100 8-759-042-02 IC S-80743AL-A7-S (KV-XF29M35 ONLY) <PHOTO COUPLER> PH600 ! 8-749-924-35 IC301 8-752-088-39 IC CXA2130S PHOTO COUPLER ON3171-R IC502 8-759-700-07 IC NJM2903M IC503 8-759-980-58 IC TDA8172...
Page 64
KV-XF29M35/XF29M63/XF29M93 RM-954 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK R008 1-216-065-91 RES,CHIP 4.7K 1/10W R113 1-216-025-91 RES,CHIP...
Page 67
KV-XF29M35/XF29M63/XF29M93 RM-954 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK C1422 1-164-346-11 CERAMIC CHIP C3259 1-125-798-91 ELECT 0.47MF...
Page 68
KV-XF29M35/XF29M63/XF29M93 RM-954 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK C6221 1-125-798-91 ELECT 0.47MF D1411 8-719-158-35 DIODE RD9.1SB...
Page 69
KV-XF29M35/XF29M63/XF29M93 RM-954 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK <IC LINK> R1459 1-216-025-91 RES,CHIP 1/10W R1460 1-216-033-00...
Page 70
KV-XF29M35/XF29M63/XF29M93 RM-954 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK R3242 1-216-081-00 RES,CHIP 1/10W R6205 1-216-073-00 RES,CHIP 1/10W...
Page 71
! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK * A-1331-872-A C BOARD, COMPLETE (KV-XF29M35) D720 8-719-911-19 DIODE 1SS119-25 ******************** D721 8-719-911-19 DIODE 1SS119-25...
Page 72
RES, ADJ, CARBON 47K <IC> IC2801 8-759-700-07 IC NJM2903M *********************************************************************** IC2803 8-759-701-59 IC NJM78M09FA IC2805 8-759-998-98 IC LM358D * A-1343-586-A D1 BOARD, COMPLETE (KV-XF29M35) ********************* <CHIP CONDUCTOR> * A-1343-640-A D1 BOARD, COMPLETE (KV-XF29M63/XF29M93) ********************* JR2803 1-216-295-91 SHORT JR2804 1-216-295-91 SHORT JR2815...
Page 73
! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK <RESISTOR> * A-1241-346-A F BOARD, COMPLETE (KV-XF29M35) ******************** R2801 1-216-081-00 RES,CHIP 1/10W * A-1241-361-A F BOARD, COMPLETE (KV-XF29M63/XF29M93) R2803 1-216-057-00 RES,CHIP 2.2K...
Page 75
! are critical for safety. Replace only with part number specified. 1 (KV-XF29M35 ONLY) REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK * A-1347-155-A V1 BOARD, COMPLETE (KV-XF29M35 ONLY) JR807 1-216-295-91 SHORT ********************* JR808 1-216-295-91 SHORT <TRANSISTOR>...