Summary of Contents for Sony FD Trinitron KV-29XL70E
Page 1
All manuals and user guides at all-guides.com SERVICE MANUAL AE-6B CHASSIS MODEL MODEL COMMANDER DEST CHASSIS NO. COMMANDER DEST CHASSIS NO. KV-29XL70E KV-29XL71E RM-944 SCC-Q81X-A RM-934 SCC-Q81W-A KV-29XL70K KV-29XL71K RM-944 OIRT SCC-Q82M-A RM-934 OIRT SCC-Q82N-A RM-934 KV-29XL70/71 RM-944 - 1 -...
PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE TANCE CRITIQUE POUR LA SÈCURITÈ DU FONCTIONNEMENT, NE LES REMPLACER QUE PAR DES COMPSANTS SONY DONT THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN LE NUMÈRO DE PIÈCE EST INDIQUÈ...
Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics. For more information on the use of Lead Free Solder, please refer to http://www.sony-training.com - 3 -...
All manuals and user guides at all-guides.com 21 pin connector Pin No Signal Signal level Audio output B Standard level : 0.5V rms (right) Output impedence : Less than 1kohm* Audio input B Standard level : 0.5V rms (right) Output impedence : More than 10kohm* Audio output A Standard level : 0.5V rms (left)
All manuals and user guides at all-guides.com AE-6B SELF DIAGNOSTIC SOFTWARE The identification of errors within the AE-6B chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous flashing LED) and then communicate with each device in turn to establish if a device is faulty.
All manuals and user guides at all-guides.com SECTION 2 DISASSEMBLY 2-1. Rear Cover Removal 2-2. Speaker Connector Disconnection => => Remove the rear cover fixing screws indicated and pull the Before completely removing the rear cover disconnect the rear cover backwards away from the set. speaker connector which is located on the inside of the set.
All manuals and user guides at all-guides.com 2-4. Service Position 2-5. G Board Removal Clips To remove the G Board release the clips circled and ease the To place the chassis in the service position, remove the H board gently away from the support bracket. bracket and stand the chassis as shown above.
All manuals and user guides at all-guides.com 2-8. Picture Tube Removal WARNING: BEFORE REMOVING THE ANODE CAP High voltage remains in the CRT even after the power is disconnected. To avoid electric shock, discharge CRT before attempting to remove the anode cap.
All manuals and user guides at all-guides.com SECTION 3 SET-UP ADJUSTMENTS • When complete readjustment is necessary or a new picture tube Carry out the adjustments in the following order : is installed, carry out the following adjustments. 3-1. Beam Landing. •...
All manuals and user guides at all-guides.com Fig.3-4 Align both Purity Purity magnets Purity control magnets magnets to the vertical position Align pips on each magnet 3-2. Convergence (1) Screen centre convergence [Static convergence] Input a dot pattern signal from the pattern generator. Normalize the picture setting.
Page 19
All manuals and user guides at all-guides.com Correction for HMC [Horizontal mis-convergence] and VMC HTIL correction can be performed by adding a THL correction [Vertical mis-convergence] by using the BMC [Hexapole] assembly to the Deflection yoke. magnet. a). HMC correction by BMC [Hexapole] magnet and movement of the electron beam.
All manuals and user guides at all-guides.com Layout of each control 3-3. Focus Adjustment Receive a television broadcast signal. Normalize the picture setting. Purity magnet Adjust the focus control located on the flyback transformer to BMC (Hexaploe) magnet obtain the best focus at the centre of the screen. V STAT convergence magnet Bring only the centre area of the screen into focus, the magenta- Y-splitting axis correction magnet...
All manuals and user guides at all-guides.com SECTION 4 CIRCUIT ADJUSTMENTS 4-1. Electrical Adjustments Service adjustments to this model can be performed using the supplied remote Commander RM-944 (KV-29XL70) or RM-934 (KV-29XL71). How to enter into the Service Mode Turn on the main power switch and enter into the stand-by mode.
Page 22
All manuals and user guides at all-guides.com Sub Brightness Adjustment Input a Monoscope pattern. Set the TV set or operation in Service Mode. [ See Page 21 ]. Select ‘Service’ from the on screen menu display and press ‘Right Arrow’. The ‘Service’...
All manuals and user guides at all-guides.com Deflection System Adjustment 4-2. TEST MODE 2: Set the TV set or operation in Service Mode. Test Mode 2 is available by setting the TV for operation in Service [ See Page 21 ]. Mode [ As shown on Page 21 ] , OSD ‘TT’...
All manuals and user guides at all-guides.com 5-1. BLOCK DIAGRAMS (1) IC7300 VIDEO OUT (RED) CN2912 CN7301 HP L J7375 HP R J2901 TO A BOARD POWER CN2502 SWITCH HEADPHONES KEY 1 Q7355 S0900 - S0905 KEY 2 CN6400 CN6401 IC7325 F6400 AC IN...
All manuals and user guides at all-guides.com 5-1. BLOCK DIAGRAMS (2) DF DRIVE Q8851 M PIN DY ASSY CONTROL CN8810 CN8611 Q8805 COMPARATOR IC8103 V STAT V- DY+ DF DRIVE V- DY- TO A BOARD (1/ V DY H CENTRE BUFFER H LIN CN5002...
All manuals and user guides at all-guides.com 5-1. BLOCK DIAGRAMS (3) 5-2. CIRCUIT BOARD LOCATION Reference Information IC0004 RESISTOR : METAL FILM COMPARATOR (AV-LINK CIRCUIT) : SOLID C Board FPRD : NON FLAMMABLE CARBON FUSE : NON FLAMMABLE FUSIBLE : NON FLAMMABLE METAL OXIDE IC0003 IC0001 RESET CIRCUIT...
All manuals and user guides at all-guides.com TO H6 BOARD CN2912 A . . - 2 9 X L 7 0 / 7 1 VIDEO A 2/6 MUTE A 2/6 TO F1 BOARD CN0891 +9V REG +5V REG SCART AUDIO A 2/6 +3.3V REG +1.8V REG...
Page 28
All manuals and user guides at all-guides.com A . . - 2 9 X L 7 0 / 7 1 COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL MUTE A 1/6 M S P 3 4 1 1 G - Q A - B 1 1 82PF 8.2UH 82PF...
Page 29
All manuals and user guides at all-guides.com A . . - 2 9 X L 7 0 / 7 1 COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL MICRO A 1/6 DEFLECTION CONTROL CCT 7.5K VIDEO A 1/6 2 7 K MMDL914T1 2 .
Page 30
All manuals and user guides at all-guides.com A . . - 2 9 X L 7 0 / 7 1 COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL VERTICAL DEFLECTION & ROTATION COIL A 3/6 3 . 3 K A 3/6 VDP-OUT VDN-OUT...
Page 31
All manuals and user guides at all-guides.com A..-29XL70/71 VIDEO A 1/6 6 8 P F 1 0 0 0 . 1 V S P 9 4 0 2 A - V K - B 1 3 G VSYNC A 6/6 S D A 9 4 8 8 X - B 2 3 G E G HSYNC A 6/6...
Page 32
All manuals and user guides at all-guides.com A..-29XL70/71 +5V REG MICRO A 1/6 VIDEO RF A 5/6 +3.3V REG 100PF 3 3 K RESET A 5/6 VSYNC A 5/6 HSYNC A 5/6 T O M B O A R D CVBS TXT A 5/6 INTERFACE...
Page 33
All manuals and user guides at all-guides.com TUNER COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL ~ A Board Schematic Diagram [ Tuner ] Page 7/7 ~ - 33 -...
All manuals and user guides at all-guides.com ~ A Board IC Voltage Table ~ ~ A Board Semiconductor Voltage Table ~ ~ A Board Waveforms ~ 2ms/div 10us/div 5ms/div 5ms/div 5ms/div 20us/div 264 mVp-p (H) 272 mVp-p (H) 744 mVp-p (V) 53 Vp-p (V) 1.4 Vp-p (H) 688 mVp-p (H)
All manuals and user guides at all-guides.com ~ F1 Board Schematic Diagram [ Power Switch, Fuse, SIRCS and Stand-By LED ] ~ ~ H6 Board Schematic Diagram [ Front AV Input, Headphone and Control Switches ] ~ F1.-29XL70/71 A BOARD A BOARD CN2502 CN2000...
All manuals and user guides at all-guides.com ~ G Board Semiconductor Location Table ~ ~ G Printed Wiring Board Conductor side ~ ~ H6 Printed Wiring Board Conductor side ~ Note : Portions of the circuit contained within the marked areas as shown have high voltages present.
All manuals and user guides at all-guides.com ~ D Printed Wiring Board Conductor side ~ ~ D Board Waveforms ~ ~ D Board IC Voltage Table ~ ~ D Board Semiconductor Voltage Table ~ 10us/div 10us/div 10us/div 10us/div 10us/div 2.44 Vp-p (V) 148 Vp-p (V) 2.36 Vp-p (H) 152 Vp-p (H)
All manuals and user guides at all-guides.com ~ C Printed Wiring Board Conductor side ~ ~ M Printed Wiring Board Conductor side A ~ ~ C Board Waveforms ~ 10us/div 10us/div 2.16 Vp-p (H) 2.0 Vp-p (H) 10us/div 10us/div ~ M Printed Wiring Board Conductor side B ~ 1.9 Vp-p (H) 6.8 Vp-p (H) 10us/div...
All manuals and user guides at all-guides.com 5-5 IC BLOCK DIAGRAMS A BOARD IC6202/IC6205 BA033T/BA12T REFERENCE VOLTAGE A BOARD IC2500 TDA7497 VOLUME OP AMP MUTE/STBY PROTECTIONS VOLUME OP AMP G BOARD IC6001 MCZ3001D Remote Internal Driver DVLD ref 5v Sel=34v 15v/8v Reg.
Page 49
All manuals and user guides at all-guides.com A BOARD IC2000 MSP3411G SBUS Interface I2C Interface DEMODULATOR IDENT SCART Switching Facilities G BOARD IC6003 SE135N-LF4 A BOARD IC5301/IC5302 LA6393DLL A BOARD IC5400 STV9379 A BOARD IC5300 LM358N FLYBACK GENERATOR POWER AMPLIFIER THERMAL PROTECTION - 49 -...
All manuals and user guides at all-guides.com SECTION 6 EXPLODED VIEWS NOTE : Items with no part number and no description are not Items marked “*” are not stocked stocked because they are seldom required for routine since they are seldom required for routine service.
All manuals and user guides at all-guides.com SECTION 7 ELECTRICAL PARTS LIST PARTS LISTING TABLE OF CONTENTS Page H6 BOARD COMPLETE Parts List : ....................53 C BOARD COMPLETE Parts List : ....................53 F1 BOARD COMPLETE Parts List : ....................
Page 59
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK D3008 8-719-109-89 DIODE RD5.6ESB2 < IC > D3009 8-719-929-15 DIODE HZS9.1NB2 D3011 8-719-929-15 DIODE HZS9.1NB2 IC1001 6-704-747-01 IC TDA9886TS/V4B D3013 8-719-929-15 DIODE HZS9.1NB2 IC2000 6-701-031-11 IC MSP3411G-QA-B11 D3015 8-719-929-15...
Page 60
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK L2501 1-535-303-00 LEAD, JUMPER (5.0MM) Q2002 8-729-010-29 TRANSISTOR MSD601-RST1 L3000 1-216-295-91 SHORT CHIP Q2003 8-729-010-29 TRANSISTOR MSD601-RST1 L3004 1-216-295-91 SHORT CHIP Q2004 8-729-010-29 TRANSISTOR MSD601-RST1 L3005 1-216-295-91 SHORT CHIP...
Page 61
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK Q7018 8-729-010-05 TRANSISTOR MSB709-RT1 R1037 1-216-829-11 METAL CHIP 4.7K 5% 1/10W Q7019 8-729-010-29 TRANSISTOR MSD601-RST1 R1038 1-216-833-11 METAL CHIP 1/10W R1039 1-216-801-11 METAL CHIP 1/10W <...
Page 62
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK R2068 1-216-049-11 RES-CHIP 1/10W R2930 1-216-295-91 SHORT CHIP R2069 1-216-837-11 METAL CHIP 1/10W R2933 1-216-295-91 SHORT CHIP R2070 1-216-833-11 METAL CHIP 1/10W R2936 1-216-295-91 SHORT CHIP R2071 1-216-839-11 METAL CHIP...
Page 63
All manuals and user guides at all-guides.com H5 D2 REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK R3230 1-216-025-11 RES-CHIP 1/10W R5203 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R3233 1-216-821-11 METAL CHIP 1/10W R5204 1-216-809-11 METAL CHIP 1/10W R3234 1-216-821-11 METAL CHIP 1/10W R5206...
Page 64
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK R5320 1-216-833-11 METAL CHIP 1/10W R5871 1-216-850-11 METAL CHIP 270K 5% 1/10W R5321 1-216-837-11 METAL CHIP 1/10W R5872 1-216-073-91 RES-CHIP 1/10W R5322 1-216-820-11 METAL CHIP 1/10W R5873 1-216-073-91...
Page 65
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK R7079 1-216-041-00 RES-CHIP 1/10W < CONNECTOR > R7080 1-216-043-91 RES-CHIP 1/10W R7081 1-216-817-11 METAL CHIP 1/10W CN0001 * 1-793-497-11 CONNECTOR, BOARD TO BOARD 40P R7082 1-208-782-11 METAL CHIP 0.5% 1/10W...
Page 66
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK R0014 1-216-081-00 RES-CHIP 1/10W R0073 1-216-809-11 METAL CHIP 1/10W R0016 1-216-025-11 RES-CHIP 1/10W R0074 1-216-809-11 METAL CHIP 1/10W R0017 1-216-093-91 RES-CHIP 1/10W R0075 1-216-025-11 RES-CHIP 1/10W R0018 1-216-025-11...
Page 67
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK C6034 1-162-968-11 CERAMIC CHIP 0.0047UF 10.00% 50V FB6005 1-535-303-00 LEAD, JUMPER (5.0MM) C6035 1-136-497-81 FILM 0.1UF 5.00% 50V FB6006 1-535-303-00 LEAD, JUMPER (5.0MM) C6036 1-136-479-11 FILM 0.001UF 5.00% 100V...
Page 68
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK * A-1640-432-A D Board Complete R6020 1-216-820-11 METAL CHIP 1/10W R6021 1-216-362-11 METAL OXIDE 0.27 5% R6022 1-216-833-11 METAL CHIP 1/10W 4-382-854-01 SCREW (M3X8), P, SW (+) R6024 1-216-615-11 METAL CHIP...
Page 69
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK C8815 1-117-835-11 FILM 6200PF 3.00% 1.5KV D8128 8-719-081-97 DIODE MMDL914T1 C8816 1-162-964-11 CERAMIC CHIP 0.001UF 10.00% 50V D8129 8-719-081-97 DIODE MMDL914T1 C8817 1-125-893-11 FILM 680PF 3.00% 1.5KV D8132 8-719-081-97...
Page 71
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK R8175 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W R8817 1-216-361-00 METAL OXIDE 0.22 5% R8176 1-216-838-11 METAL CHIP 1/10W R8818 1-249-405-11 CARBON 1/4W R8177 1-216-830-11 METAL CHIP 5.6K 5% 1/10W R8819...
Page 72
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK * A-1300-626-A VM Board Complete Q7403 8-729-119-78 TRANSISTOR 2SC2785-HFE Q7404 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R 4-382-854-01 SCREW (M3X8), P, SW (+) Q7405 8-729-026-39 TRANSISTOR 2SA933AS-QT Q7406 8-729-045-05 TRANSISTOR 2SA2005 <...
Page 73
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK MISCELLANEOUS £ 1-571-433-21 SWITCH, PUSH (AC POWER) £ 1-823-853-11 CORD, POWER 1-424-855-11 COIL, CHOKE 29MMH 8-598-623-10 TUNER FSS BTP-AC421 £ 1-453-340-41 TRANSFORMER ASSY, FLYBACK (NX-4522//Z2B4) 1-529-408-11 SPEAKER (4.2X24CM) 1-910-000-50 WOOFER LS £...
Page 74
• User programmable Functional Check through Infrared • Fast and documented Test Mode setting of all Sony TV chassis Additional features such as Adjustments and Troubleshooting are available in chassis-dependent software modules. Please contact your local Sony Service organisation for the latest information.