hit counter script
Husqvarna R 214T Workshop Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Lawn Mower
  5. R 214T
  6. Workshop manual

Husqvarna R 214T Workshop Manual

Hide thumbs Also See for R 214T:
Table of Contents

Advertisement

Quick Links

Workshop manual
R 214T, R 214TC
English
1676 - 001 - 26.11.2021

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna R 214T

Summary of Contents for Husqvarna R 214T

  • Page 1 Workshop manual R 214T, R 214TC English 1676 - 001 - 26.11.2021...

  • Page 2: Table Of Contents

    Contents 1 Introduction 9 Repair instructions 1.1 General..............3 9.1 Chassis..............18 1.2 Document description..........3 9.2 Propulsion system..........24 1.3 Target group............3 9.3 Electrical system..........29 1.4 Revisions..............3 9.4 Fuel system............32 1.5 Safety..............3 9.5 Hydraulic system..........32 1.6 Servicing tools............3 9.6 Cutting system.............

  • Page 3: Introduction

    1 Introduction 1.1 General This publication covers Husqvarna ride-on lawn mowers R 214T, R214TC model year 2021. Workshop manual are available for models that are no longer sold. 1.2 Document description This manual gives a full description of how to do maintenance and repair on the product.

  • Page 4: Safety

    2 Safety 2.1 General safety instructions • Explosive gases can come from the battery. Do not smoke near the battery. Keep the battery away from WARNING: Read the warning instructions that open flames and sparks. follow before you use the product. 2.4 Risk of sparks The service center that repairs the product must have Sparks can occur when you do work on the battery and...

  • Page 5: Transport Safety

    Look out for ejecting objects and ricochets. Max. ethanol 10%. Never use the product if persons, especially children, or animals, are in the Cutting height. vicinity. The service position for the cutting height Look behind you before and while you lever.

  • Page 6: To Put Supports Below The Product

    WARNING: Always put supports on the 2 sides 3. Apply the parking brake. of the product to make it stable. 4. If the product has , lock the product with Husqvarna Connect. 1. Park the product on a hard and level ground.
  • Page 7 5. Put the rear supports below the rear transmission frame. 1676 - 001 - 26.11.2021 Safety - 7...

  • Page 8: Prepare And Do Servicing On The Product

    3 Prepare and do servicing on the product 3.1 Pre delivery inspection Complete the sales certificate and the customer records. Write the serial number in the operator's manual and confirm the delivery service in the service book. 8 - Prepare and do servicing on the 1676 - 001 - 26.11.2021 product...

  • Page 9: Assembly 4.1 Battery

    Charge the battery at 12V, maximum 3A for 4 hours. 1. Put the seat in the frame. Servicing Use a Husqvarna battery charger. Refer to 2. Install the 2 screws (A). tools on page 15 . 4.2 To assemble the steering wheel 1.
  • Page 10 4. Release the clip on the front cover with the tool 9. Put a wooden block between the equipment frame attached to the ignition key, and remove the cover. and the chassis. This makes sure that the cutting deck does not spring back when removed. 5.

  • Page 11: To Do A Check Of The Parallelism Of The Cutting Deck

    4.8 To do a check of the parallelism of the 7. The oil level must be between the marks on the dipstick. If the level is near the ADD mark, fill oil to cutting deck the FULL mark. 1. Make sure that the air pressure in the tires is correct. Wheels on page 9 .

  • Page 12: Function Test

    5 Function test 5.1 Operation conditions These conditions are necessary to start the engine: • The parking brake is applied. • The cutting deck is lifted. The engine must stop in these situations: • The parking brake is not applied and the operator lifts from the seat.

  • Page 13: Maintenance Schedule For The Service Center

    6 Maintenance schedule for the service center 1. PREPARE THE PRODUCT First serv- Maintenance interval icing in hours Do a check of the battery. Do a check of the blades. Do a check of the belts and pulleys. Do a check of the steering chain of the inner side of the frame tunnel. Do an inspection, lubricate and adjust all wires.
  • Page 14 4. CUTTING EQUIPMENT First serv- Maintenance interval icing in hours Clean the outer and inner surfaces of the cutting deck and the cutting deck cov- ers. Do a check of and adjust the cutting height. Do a check of and adjust the parallelism of the cutting deck. Refer to To do a check of the parallelism of the cutting deck on page 11 .

  • Page 15: Servicing Tools

    7 Servicing tools 7.1 Servicing tools Counterhold – Belt pulley 506 89 92-01 Punch kit 535 41 32-01 Puller – Belt pulley 506 66 48-01 Battery charger (EU) 580 35 52-01 Tachometer 502 71 14-01 Tool for center spring 506 89 93-01 Hex key 506 79 06-01 Adjustment tool for wheel speed...

  • Page 16: Function Overview

    8.3 Engine The transmission serial number (B) is found behind the The product has an air-cooled Husqvarna engine. wheels on the left side of the product. Information about engine repairs are not given in the The product serial number (C) is found on the printed workshop manual.

  • Page 17: Transmission

    8.4 Transmission The turning radius with articulated steering is very small. At full lock the circle with grass that is not cut is only 20– The product has a hydrostatic transmission. Forward 30 cm/8"–12" for different models. and rearward pedals adjust the speed. The hydraulic pump is in the rear axle.

  • Page 18: Repair Instructions

    9 Repair instructions 9.1 Chassis 5. Remove the screws from the hinges. 9.1.1 To remove the covers 9.1.1.1 To open the engine cover 1. Fold the seat forward. 2. Release the clip on the engine cover with the tool attached to the ignition key. 6.
  • Page 19 9.1.1.5 To remove the left footrest plate 9.1.1.8 To remove the frame tunnel cover • Remove the 4 screws and remove the footrest plate. 1. Remove the 2 screws (A). 2. Push the frame tunnel cover rearward (B) and lift the front end of the frame tunnel cover (C).
  • Page 20 9.1.2.2 To adjust the throttle cable WARNING: Do not park the product on a grass slope when you do a check of the Note: The throttle cable looks different on different parking brake. engine models. 2. Push the parking brake pedal (A) down. 1.
  • Page 21 3. Remove the snap ring. 5. Remove the idler spring. 4. Pull off the wheel from the axle. 5. Collect the spacer sleeve and washers from the axle. 6. Remove the ball joint for the speed control (A). 6. Install in opposite sequence. 9.1.6 Rear axle 9.1.6.1 To disassemble the pivoting rear axle 1.
  • Page 22 11. Remove the rear belt from the idler pulley and 9.1.6.2 To replace the bushings on the pivoting rear axle remove the pulley. CAUTION: When the pivoting rear axle is removed, replace the bushings in the rear 12. Remove the snap ring (A) and washer from the frame.
  • Page 23 7. Install the rear belt. 4. Remove the inner snap ring (A) from the lower bearing. 8. Install the hydrostatic transmission fan. 9. Install the hydrostatic transmission cable. Make sure that the hydrostatic transmission is correctly To adjust the hydrostatic adjusted.

  • Page 24: Propulsion System

    9.2 Propulsion system 6. Loosen the clips that hold the throttle cable and, if attached, the choke cable. Disconnect the cables from the carburetor casing. 9.2.1 To remove and install the engine To remove the 1. Remove the engine cover. Refer to engine cover on page 18 2.
  • Page 25 9. Remove the transmission belt spring from the belt 13. Hold the belt pulley with a counterhold and remove tensioner. the Allen screw that holds the belt pulley and engine Servicing tools on page 15 together. Refer to 10. Lift the transmission belt from the tension pulley. 11.
  • Page 26 9.2.3 To replace the engine oil and oil filter Note: The belt pulley groove must align with the output shaft key. Make sure that the spacer pipe (A) If the engine is cold, start the engine for 1–2 minutes and shaft key (B) are attached to the engine shaft. before you drain the engine oil.
  • Page 27 4. Turn the oil drain plug counterclockwise and pull out 11. Lightly lubricate the rubber seal on the new oil filter to open it. with new oil. 12. Turn the oil filter clockwise by hand until the rubber seal is in position, then tighten the oil filter a half turn more.
  • Page 28 3. Make sure that the oil level in the transmission oil 4. Install in the opposite sequence. tank is between the 2 horizontal lines on the tank. 9.2.6 To examine and replace a spark plug 1. Open the engine cover. 2.

  • Page 29: Electrical System

    9.3 Electrical system 9.3.1 Electrical system overview 1. Battery 5. Safety switch for the lift lever 2. Main fuse 6. Ignition lock 3. Operator presence control (OPC) 7. Hour meter 4. Microswitch, parking brake 1676 - 001 - 26.11.2021 Repair instructions - 29...
  • Page 30 9.3.2 Electrical diagram Key position Position Function Contact Engine START L+B+S Cable side Hours Start key switch Start S M B L G motor Cable side Cable side White Power relay Brown Lift switch Yellow Blue Green Black Brown Cable side Cable side Battery P-Brake switch...
  • Page 31 9.3.3 To replace the main fuse 9.3.5 To remove and install the microswitch for the lift lever A blown fuse is identified by a burned connector. 1. Remove the right footrest plate and the right fender. 1. Open the engine cover. The main fuse is in a holder To remove the covers on page 18 Refer to in front of the battery.

  • Page 32: Fuel System

    9.4 Fuel system 4. Disconnect the fuel tank hose from the lower connection of the fuel filter. 9.4.1 To replace the fuel filter 5. Pull the hose through the frame. 1. Open the engine cover to get access to the fuel 6.
  • Page 33 11. Close the clutch valve. CAUTION: Do not operate the speed pedals when the controls for the clutch valves is disengaged. 1. Put the product on the adjustment tool for wheel Servicing tools on page 15 speed. Refer to Note: There are 2 valves on AWD products. 12.
  • Page 34 To remove 6. Remove the transmission belt. Refer to 9.5.4 To replace the shaft seals of the hydrostatic the transmission belt on page 45 . transmission 7. Remove the 5 screws that hold the rear transmission 9.5.4.1 To replace the input shaft seal of the hydrostatic and lower the rear transmission.
  • Page 35 8. Use the thick end of ¼ in extension to carefully tap 4. Wind insulating tape around the input shaft to down the seal. Move the extension around the seal prevent damage to the new seal from the keyway until the seal is level with the top edge of the shaft and the groove.
  • Page 36 10. Fill the transmission oil tank until the oil is at the 6. Remove the locking spring and the ball joint on the maximum level. The product must be level and the rear hydrostatic transmission cable from the arm. oil must have a temperature of approximately 20 °C. Remove the rear clamp.
  • Page 37 4. Attach the front cable clamp for the hydrostatic 11. Put the locking spring into the hole (A) and push it transmission. around the ball joint shaft (B). 12. Tighten the locknut for the rear ball joint. To remove 13. Attach the frame tunnel cover. Refer to the covers on page 18 .
  • Page 38 6. Make a mark at the position where the wheels start 3. Disconnect the ball joint from the hydrostatic to turn (C). transmission cable by removing the lock spring. 4. Make sure that the forward pedal is fully pushed. 5. Bend the arm to fully and do a check that the ball and the ball socket in the ball joint align.

  • Page 39: Cutting System

    9.6 Cutting system 3. Fold down the cutting deck and push it in until it stops. 9.6.1 To put the cutting deck in servicing position WARNING: The tension spring for the drive belt can break and cause injury. Use protective glasses.
  • Page 40 5. To make sure that no weight is applied on the 3. Turn the adjustment nut to extend the lifting rod or support wheels, put a wooden block between the make it shorter. Extend the lifting rod to lift the rear frame and the bathroom scale.
  • Page 41 9.6.6 To replace the blades 5. Loosen the 4 screws that hold the blade bearing and remove the bearing assembly from the cutting deck. To remove and 1. Remove the cutting deck. Refer to attach the cutting deck on page 9 . 2.

  • Page 42: Equipment Frame

    8. Make a mark on one end of the shaft. Push out the 6. If the blade rotates, remove material with the file at shaft with a puller. Tap out the bearing and remove the end of the blade that points down. Do this until the spacer.

  • Page 43: Steering

    9.8 Steering 9.8.2 To replace the steering cable 9.8.1 To examine and adjust the steering cables The tension of the steering cables can decrease after a period of time. This causes the adjustment of the steering to change. Examine and adjust the steering as follows: CAUTION: Do not tighten the cables too much.

  • Page 44: Belts

    3. Remove the screw (A) and the washer (B). 3. Put the cables below the steering cable rollers (E) below the tunnel cover. 4. Tension and adjust the steering cables. Refer to examine and adjust the steering cables on page 43 . 4.
  • Page 45 3. Remove the snap ring and remove the cooling fan. Engine pulley to Transmission Belt 1 transmission pul- belt Engine pulley to Belt 2 Main belt intermediate pul- Intermediate pul- Belt 3 Equipment belt ley to cutting deck 4. Disengage the spring on the belt tensioner. 9.9.2 To lubricate the belt adjuster The belt adjuster must be lubricated regularly with a good quality molybdenum disulphide grease.
  • Page 46 7. Remove the belt guide for the main belt. 3. Put the transmission belt on the hydrostatic transmission pulley and on the belt tensioner. 4. Attach the cooling fan and the snap ring for the cooling fan. 8. Pull the main belt from the engine pulley and put it to the side.
  • Page 47 9.9.5 To remove and attach the main belt 9.9.6 To replace the equipment belt 1. Remove the rear belt guide for the main belt. Note: Remove the equipment belt when you attach a snow blade on the product. 1. Lower the cutting deck. To remove the 2.
  • Page 48 8. Install in opposite sequence. 9.9.7 To replace the belt on the cutting deck To remove and 1. Remove the cutting deck. Refer to attach the cutting deck on page 9 . 2. Remove the 4 screws and lift the frame. 3.

  • Page 49: Troubleshooting

    10 Troubleshooting 10.1 Troubleshooting schedule Fault Possible cause Steps Troubleshooting Procedure The start motor Cutting deck Make sure that the lift lever is in the top position. Move the lift lev- does not start lowered. er to the top po- when the key sition if it is nec- switch is turned...
  • Page 50 Fault Possible cause Steps Troubleshooting Procedure The start motor Wiring fault. Do a check that the yellow cable to the engine gets Repair the cable operates cor- voltage from the battery when the key switch is in ig- or replace the rectly but the nition position.

  • Page 51: Technical Data

    11 Technical data 11.1 Technical data R 214T R 214TC Dimensions Length without cutting deck, mm 1942 1942 Width without cutting deck, mm Length including cutting deck , mm 2227 2227 Width including cutting deck , mm Height, mm 1131...
  • Page 52 R 214T R 214TC Electrical system Type 12V, negative grounded 12V, negative grounded Battery 12V, 24Ah 12V, 24Ah Spark plugs Husqvarna HQT-7 Husqvarna HQT-7 Electrode gap, mm/inch 0.75 / 0.030 0.75 / 0.030 Cutting deck Type Combi 94 Combi 94...

  • Page 53: Control Points And Play

    11.2 Control points and play Control points Parallelism cutting deck with cutting height in position 1 ± 2 mm / ± 0.079 in Control of cutting height in position 1 25 ± 2 mm / 0.98 ± 0.079 in Distance between support plate and drive belt 3-6 mm /1/8 in -1/4 in Distance belt tensioner lever arm and belt guide, disen- 17 ±...
  • Page 54 54 - Technical data 1676 - 001 - 26.11.2021...
  • Page 55 1676 - 001 - 26.11.2021 Technical data - 55...
  • Page 56 114 27 2021-12-02...

This manual is also suitable for:

R 214tc

Table of Contents