Advertisement
Quick Links
Quick Setup Guide
Congratulations on the purchase of your new Samsung TV.
Read this setup guide to get your TV up and running quickly.
1-800-SAMSUNG (1-800-726-7864)
STOP
Samsung Electronics America, Inc.
85 Challenger Road Ridgefield Park, NJ 07660-2112
Please do not return this unit.
Samsung Electronics Canada Inc.
55 Standish Court Mississauga, Ontario L5R 4B2
If you have problems operating your
Call Center hours of operation: Mon-Sun, 9:00 AM -12
TV, call:
AM EST.
1-800-SAMSUNG (1-800-726-7864)
To register this product, visit: www.samsung.com/
For web support please visit:
register.
www.samsung.com/support
Step 1
: Install the Stand
Follow the steps below to connect the TV to the stand.
✎
NOTE
x
Make sure to distinguish between the front and back of the Stand and
Guide Stand when assembling them.
x
Make sure that at least two persons lift and move the PDP TV.
x
Stand the product up and fasten the screws. If you fasten the screws with
the PDP TV placed down, it may lean to one side.
1
2
With your TV upright, connect the
Fasten the two screws (M4 X L16)
TV to the Stand as shown.
at position 1, and then fasten the
two screws (M4 X L16) at position
2.
Front
2
Rear
1
Step 2
: Install the Batteries into the Remote
To install batteries into your remote control,
follow these steps:
1. Lift the cover on the back of the remote
upward as shown in the figure to the
right.
2. Install two AAA batteries.
✎
Make sure to match the + and -
ends of the batteries to the diagram in the battery compartment.
3. Replace the cover.
Step 3
: Connect Power and Antenna or Cable
VHF/UHF Antenna
Connect Ant In to
• Wall cable jack
• VHF/UHF Antenna
or
• Cable or Satellite box
Ant or Cable Out
Best to use 75 ohm (round) cable.
Make sure the AC power cord is plugged in securely to
the wall outlet and the TV.
Antenna Cable (Not Supplied)
Step 4
: Connect External Devices
Connecting an AV device (DVD/ Blu-ray player, cable/satellite box, etc.)
Use one of the connections below to connect your TV to an external A/V device. We recommend using HDMI for the highest picture quality.
Audio Cable
(Not Supplied)
HDMI to DVI Cable
(Not Supplied)
Very Good Connection
HD connection (up to 720p/1080i)
Using a HDMI to DVI Cable
Device
AUDIO OUT
DVI OUT
Good Connection
Component connection (up to 720p/1080i)
Using a Component Cable
DVD / Blu-ray player / HD Cable Box / HD Satellite receiver (STB)
Device
COMPONENT OUT
AUDIO OUT
Audio Cable (Not Supplied)
Step 5
: Run Plug & Play
When you turn on your TV for the first time, it automatically launches the Plug &
Play function. With Plug & Play, you can select the On Screen Display language,
set the clock mode, and launch the TV's channel memorizing process.
It also displays connection instructions similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow
buttons on your remote. To make a selection, press the ENTERE button.
To skip a screen, press the
MENU
button. To turn on your TV, press the
button on the remote or on the TV. To run Plug & Play, follow these steps:
1
Plug & Play
Using your remote control,
Plug & Play
select the language for the On
Select Language of the OSD.
English
Screen Display (OSD), and then
Español
Language
press the ENTERE button.
Français
U Move E Enter
2
Plug & Play
Select Home Use, and then
press the ENTERE button. If
Select 'Home Use' when installing this TV in your home.
you select Store Demo, the TV
will reset your picture and audio
Store Demo
Home Use
settings every 30 minutes.
L Move E Enter
3
Select the Antenna Source
Plug & Play
to memorize. you must select
Select the Antenna source to memorize.
Antenna Source to same type
Air
as your cable system type. After
Cable
selecting source, select Start;
then press the ENTERE
Auto
button on your remote.
U Move E Enter m Skip
Best Connection
HD connection (up to 720p/1080i)
Using an HDMI Cable
HDMI Cable
DVD / Blu-ray player / HD Cable Box / HD STB
(Not Supplied)
(Set-Top-Box) satellite receiver
HDMI OUT
Audio Cable (Not Supplied)
Video Cable (Not Supplied)
Lowest Quality Connection
Audio/Video connection (480i only)
Using an Audio/Video Cable
DVD, Blu-ray player, cable box, STB
satellite receiver, VCR
VIDEO OUT
✎
When connecting to
AV IN
on the back of your TV, attach the
Component Cable (Not Supplied)
video cable (yellow) to the green jack next to the
The jack will not match the color of the video cable (yellow).
✎
Most cable systems are Standard(STD) systems, If you are not sure about
what kind of cable system you have, contact your cable company.
✎
If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After
Plug & Play is complete, set your TV to Channel 3 or 4, according to the
directions for your cable or satellite box.
4
POWER
The TV memorizes the available
channels. This process can take
Auto Program in Progress.
up to 45 minutes.
DTV Air : --
DTV Cable : --
5
After the TV has memorized the
channels, choose the Clock Mode.
Set the Clock Mode.
Select Auto if you have a digital
channel in your area. Select Manual
Clock Mode
if you don't, or if you have a cable or
satellite box. When done, press the
ENTERE button.
✎
If you select Manual,
the clock setting screen
appears.
6
Start
Select the daylight savings
time setting: Off, On or Auto
Set to daylight saving time.
Start
and then press the ENTERE
Start
DST
button.
Connecting an audio device (Home Theater, etc.)
Connect your TV to your Home Theater or other audio device to enjoy enhanced
Sound quality.
Audio Cable (Not Supplied)
Device
Optical Cable (Not Supplied)
Connecting a PC
Connect your TV to a PC to use it as a Monitor.
Audio Cable (Not Supplied)
HDMI to DVI Cable (Not Supplied)
Device
AUDIO OUT
label.
AV IN
7
Select the time zone in which you live, and then press ENTERE.
8
After the time zone screen, The connection method for best HD screen
quality is displayed. Press Right arrow button on your remote to view each
screen in succession. Press the Blue button to skip this section.
9
Plug & Play
The Enjoy your TV. screen appears. Then press the ENTERE button.
If You Want to Rerun Plug & Play
Air : --
1. Press the
SOURCE
button on your remote, then select TV mode.
Cable : --
Cable : 35
48%
2. Press the
MENU
button on your remote to display the menu.
3. Press the ▲ or ▼ button to select Setup, and then press the ENTERE
Stop
button.
E Enter m Skip
4. Press ENTERE again to select Plug & Play.
Plug & Play
Auto
Manual
U Move E Enter m Skip
Plug & Play
Auto
On
Auto
U Move E Enter m Skip
Analog Audio connection
Using an Audio Cable
Amplifier / DVD Home Theater
AUDIO IN
Digital Audio connection
Using an Optical Cable
Digital Audio System
OPTICAL
HD connection
Using a HDMI to DVI Cable
AUDIO OUT
DVI OUT
BN68-02608A-02
Advertisement
Related Manuals for Samsung BN68-02608A-02
Summary of Contents for Samsung BN68-02608A-02
-
Page 1: Quick Setup Guide
Quick Setup Guide Step 4 Congratulations on the purchase of your new Samsung TV. Read this setup guide to get your TV up and running quickly. Connecting an AV device (DVD/ Blu-ray player, cable/satellite box, etc.) 1-800-SAMSUNG (1-800-726-7864) STOP Use one of the connections below to connect your TV to an external A/V device. We recommend using HDMI for the highest picture quality. - Page 2 S.MODE SLEEP P.MODE P.SIZE Use these buttons in Media Play and Anynet+ modes. (�: Controls recording on Samsung recorders that have the Anynet+ feature) Changing Channels and Adjusting the Volume Adjust the volume by pressing the Volume button ✎ You can also change the channels by pressing the z button on the front panel of your TV and adjust the volume by pressing the y button.