Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear a face
instruction
shield
manual
1. SAFETY
Familiarise yourself with the applications, limitations and hazards of the press.
9
Maintain the press in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Keep the press clean for best and safest performance.
9
Locate the press in a suitable work area, on a surface that is stable, level, dry, not slippery, and capable of sustaining the load.
9
Keep area clean and tidy and free from unrelated materials, and ensure there is adequate lighting.
9
WARNING! Always wear approved eye or face protection when operating the press.
‰
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery, and contain long hair.
9
Keep hands and body clear of the work table when operating the press.
9
Maintain correct balance and footing. DO NOT over reach. Ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the working area.
9
DO NOT use the press for a task it is not designed to perform.
8
DO NOT adjust or tamper with the safety valve, or make any modifications to the press.
8
DO NOT exceed the rated capacity of the press. Avoid applying excessive force, use the pressure gauge to determine the applied load.
8
DO NOT apply off-centre loads. Ensure that workpiece is centrally loaded and correctly secured before operating the press.
8
DO NOT allow the workpiece or the arbor plates to fall from the press work bench.
8
DO NOT get the press wet or use in damp or wet locations or areas where there is condensation.
8
DO NOT operate the press when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT climb upon the press.
8
DO NOT use if bent, broken, cracked, leaking or otherwise damaged, or if press has been subjected to a shock load.
8
DO NOT operate the press if any parts are missing as this may cause failure and/or possible personal injury.
8
DO NOT use the press to compress a spring or any other item that could disengage and cause a potential hazard.
8
DO NOT stand directly in front of loaded press and never leave loaded press unattended.
8
DO NOT allow untrained persons to operate the press.
8
▲
DANGER! This model is purpose designed to withstand greater loads than the hydraulic unit can develop. For safety reasons, always
ensure the workpiece and press tools are secured on the table and will not flex or suddenly give way, causing danger to operator or
the workpiece.
WARNING! DO NOT use brake fluid, or any fluid other than a good quality jack oil, such as SEALEY HYDRAULIC JACK OIL, as
‰
this may cause serious damage to the press and will invalidate the warranty.
When not in use, release pressure from the pump and clean the press. Stand or store the arbors in a safe, childproof location.
9
2. INTRODUCTION
Heavy-duty steel frame construction with handle operated hydraulic pump unit. Screw adjustable ram and adjustable work area with removable
tray. Frame head fitted with ram pressure gauge. Storage for press pins included in frame. Supplied with press pins, flat pressing plate/V-blocks.
Suitable for workshop use or by the serious motoring enthusiast.
3. SPECIFICATION
Model No:................................................................ PPB15S
Capacity: ................................................................... 15tonne
Maximum Height - Ram to Table: ............................... 385mm
Minimum Height - Ram to Table: .................................. 45mm
Overall Height: ........................................................... 855mm
Ram Diameter: .......................................................... Ø78mm
Ram Stroke: ................................................................. 95mm
Screw Extension: ......................................................... 75mm
Table Aperture: ........................................................... 147mm
Total Ram Travel: ....................................................... 170mm
Type: ................................................................... Bench Type
Working Table Depth: ................................................. 163mm
Working Table Width: ................................................. 565mm
© Jack Sealey Limited
15TONNE PREMIER HYDRAULIC PRESS -
BENCH TYPE
MODEL NO:
Wear protective
Wear safety
gloves
footwear
Original Language Version
PPB15S
Wear protective
Beware
clothing
crushing of
hands
No reaching in
Piston rod
should face
workpiece
PPB15S
Issue 1
Place V block
correctly
18/02/22
Advertisement
Related Manuals for Sealey PPB15S
Summary of Contents for Sealey PPB15S
- Page 1 WARNING! DO NOT use brake fluid, or any fluid other than a good quality jack oil, such as SEALEY HYDRAULIC JACK OIL, as ‰...
- Page 2 6.1.3. Open release valve fig.6 by turning 180° counter clockwise. 6.1.4. Pump handle ten times. 6.1.5. Close release valve by turning handle clockwise. 6.1.6. Press is ready to use. PPB15S Issue 1 18/02/22 Original Language Version © Jack Sealey Limited...
- Page 3 7.3. To check hydraulic oil level, open the right hand top cover, and remove the oil filler plug fig.6.1. If oil needs replacing, use only Sealey hydraulic jack oil. DO NOT use brake fluid. Contact your local Sealey stockist for details). Replace oil filler plug and purge system of air.
- Page 4 Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk...