Advertisement
Quick Links
Download this manual
See also:
User Manual
Quick Setup Guide
Congratulations on the purchase of your new Samsung TV.
Read this setup guide to get your TV up and running quickly.
STOP
1-800-SAMSUNG (1-800-726-7864)
Samsung Electronics America, Inc.
85 Challenger Road Ridgefield Park, NJ 07660-2112
Please do not return this unit.
Samsung Electronics Canada Inc.
55 Standish Court Mississauga, Ontario L5R 4B2
If you have problems operating your
Call Center hours of operation: Mon-Sun, 9:00 AM -12
TV, call:
AM EST.
1-800-SAMSUNG (1-800-726-7864)
To register this product, visit: www.samsung.com/
For web support please visit:
register.
www.samsung.com/support
Step 1
: Install the Stand
Follow the steps below to connect the TV to the stand.
✎
NOTE
x
Make sure to distinguish between the front and back of the Stand and
Guide Stand when assembling them.
x
Make sure that at least two persons lift and move the PDP TV.
x
Stand the product up fasten the screws. If you fasten the screws with the
with the PDP TV placed down, it may lean to one side.
Screws (M4 X L12)
Guide Stand
Stand
Screws (M4 X L12)
1
Connect the Guide Stand to the
Stand using four screws (M4 X L10)
as shown.
Rear
2
3
With your TV upright, connect the
Fasten two screws (M4 X L12) at
TV to the Stand.
position 1, and then fasten the
two screws (M4 X L12) at position
2.
2
1
Step 2
: Install the Batteries into the Remote
To install batteries into your remote
control, follow these steps:
1. Lift the cover on the back of the
remote upward as shown in the figure
to the right.
2. Install two AAA batteries.
✎
Make sure to match the + and -
ends of the batteries to the diagram in the battery compartment.
3. Replace the cover.
Step 3
: Connect Power and Antenna or Cable
VHF/UHF Antenna
Connect Ant In to
• Wall cable jack
• VHF/UHF Antenna
or
• Cable or Satellite box
Ant or Cable Out
Use a 75 ohm (round) cable.
Make sure the AC power cord is plugged in securely to
the wall outlet and the TV.
Step 4
: Connect External Devices
Connecting an AV device (DVD/Blu-ray player, cable/satellite box, etc.)
Use one of the connections below to connect your TV to an external A/V device. We recommend using HDMI for the highest picture quality.
HDMI to DVI Cable
(Not Supplied)
Audio Cable
(Not Supplied)
Very Good Connection
HD connection (up to 1080p)
Using an HDMI to DVI Cable
Device
AUDIO OUT
DVI OUT
Good Connection
Component connection (up to 1080p)
Using a Component Cable
Top view
DVD / Blu-ray player / HD Cable Box / HD
Satellite receiver (STB)
Blu-ray player
COMPONENT OUT
AUDIO OUT
Front
Rear
Component Cable
(Not Supplied)
Step 5
: Run Plug & Play
When you turn on your TV for the first time, it automatically launches the Plug &
Play function. With Plug & Play, you can select the On Screen Display language,
set the clock mode, and launch the TV's channel memorizing process.
It also displays connection instructions similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow
buttons on your remote. To make a selection, press the ENTERE button.
To skip a screen, press the
MENU
button. To turn on your TV, press the
button on the remote or on the TV. To run Plug & Play, follow these steps:
1
Using your remote control,
select the language for the On
Select Language of the OSD.
Screen Display (OSD), and then
Menu Language
press the ENTERE button.
2
Select Home Use, and then
press the ENTERE button. If you select Store Demo, the TV will reset your
picture and audio settings every 30 minutes.
3
Select Antenna Source and Channel Source. If Antenna Source is
Cable or Auto, you must select Channel Source to same type as your
cable system type. After selecting source, select Search; then press the
ENTERE button on your remote.
✎
Most cable systems are Standard(STD) systems, If you are not sure
about what kind of cable system you have, contact your cable company.
✎
If your TV is attached to a cable or satellite box, skip Steps 3 through 5.
After Plug & Play is complete, set your TV to Channel 3 or 4, according
to the directions for your cable or satellite box.
4
The TV memorizes the available channels. This process can take up to 45
minutes.
5
After the TV has memorized the channels, choose the Clock Mode. Select
Auto if you have a digital channel in your area. Select Manual if you don't, or
if you have a cable or satellite box. When done, press the ENTERE button.
✎
If you select Manual, the clock setting screen appears.
HDMI Cable (Not Supplied)
Audio Cable
(Not Supplied)
Audio Cable
(Not Supplied)
✎
When connecting to
AV IN 1
video cable (yellow) to the green jack next to the
The jack will not match the color of the video cable (yellow).
6
Select the daylight savings time setting: Off or On, and then press the
ENTERE button
7
Select the time zone in which you live, and then press ENTERE button.
8
After the time zone screen, The connection method for best HD screen
quality is displayed. Press Right arrow button on your remote to view each
screen in succession. Press the Blue button to skip this section.
POWER
9
The Enjoy your TV. screen appears. Then press the ENTERE button.
Plug & Play
Changing the Screen Size
English
Español
:
Your TV has several screen size options, each designed to work best with specific
Français
types of video input. If you have a cable box or satellite receiver, it may have its own
U Move E Enter
set of screen sizes as well.
To change the screen size, press the
P.SIZE
you press it, your TV displays the current setting. Thereafter, each time you press
the
P.SIZE
button, you change the size of the picture on the screen.
The following sizes are available:
16:9 Wide screen
4:3 Standard screen
Zoom 1
Zoom 2
✎
Screen Fit: Displays the full image without any cut-off when HDMI (720p /
1080i / 1080p) or Component (1080i / 1080p) signals are inputted.
Connecting an audio device (Home Theater, etc.)
Connect your TV to your Home Theater or other audio device to enjoy enhanced
Sound quality.
Best Connection
HD connection (up to 1080p)
Using an HDMI Cable
DVD / Blu-ray player / HD Cable
Box / HD STB (Set-Top-Box)
Optical Cable (Not Supplied)
satellite receiver
DVD
HDMI OUT
Connecting a PC
Video Cable (Not Supplied)
Connect your TV to a PC to use it as a Monitor.
Audio Cable (Not Supplied)
Lowest Quality Connection
HDMI to DVI Cable (Not Supplied)
Audio/Video connection (480i only)
Using an Audio/Video Cable
DVD, Blu-ray player, cable box,
STB satellite receiver, VCR
Device
AUDIO OUT
VIDEO OUT
on the back of your TV, attach the
D-Sub Cable
AV IN 1
label.
(Not Supplied)
Audio Cable (Not Supplied)
Changing the Picture Mode
Your TV has four preset Picture Modes with factory adjusted settings, each
designed to give you an excellent picture under specific conditions.
To change the Picture mode, press the
time you press it, your TV displays the current setting. Thereafter, each time you
press the
P.MODE
button, you change the mode of the picture on the screen.
The Picture Modes are listed and described in the table below:
Mode
Description
Dynamic
Brightens picture. For a vibrant, enhanced image in brightly lit or
sunny room.
For a bright, detailed picture in a normally lit room.
Standard
For a studio quality cinema picture in a dimly lit or dark room.
Movie
To change the Picture Mode, follow these steps:
1. Turn on your TV, press the
The Tools menu appears.
button on your remote. The first time
2. Using the ▲ or ▼ on your remote, select Picture mode.
3. On the Picture mode menu, use the ◄ or ► on your remote to select the
Picture mode you want.
4. Press the
EXIT
button to exit the menu.
Setting the Clock
Before you can use your TV's On/Off Timer, you must set the clock. To set the
Wide Fit
clock, follow these steps:
1. Turn on your TV, press the
Time.
2. Select Clock Mode, and then press the ENTERE button.
3. Choose Auto or Manual.
Screen Fit
x
If you select Auto, the current time will be set automatically using the time
from a digital channel.
x
If you select Manual, you can set the Month, Day, Year, Hour, Minute
and am/pm directly by pressing up, down, left and right arrow button on
your remote.
4. Press the
RETURN
Analog Audio connection
Using an Audio Cable
Audio Cable
Amplifier / DVD
(Not Supplied)
home theater
AUDIO IN
Digital Audio connection
Using an Optical Cable
Digital Audio System
OPTICAL
HD connection
Using a DVI to HDMI Cable
AUDIO OUT
DVI OUT
Using an D-Sub Cable
PC OUT
AUDIO OUT
P.MODE
button on your remote. The first
TOOLS
button on your remote.
MENU
button on your remote, then select Setup →
button on your remote when done.
Advertisement
Related Manuals for Samsung PN50C675G6F
Summary of Contents for Samsung PN50C675G6F
-
Page 1: Quick Setup Guide
Quick Setup Guide Step 4 Congratulations on the purchase of your new Samsung TV. Read this setup guide to get your TV up and running quickly. Connecting an AV device (DVD/Blu-ray player, cable/satellite box, etc.) STOP 1-800-SAMSUNG (1-800-726-7864) Use one of the connections below to connect your TV to an external A/V device. We recommend using HDMI for the highest picture quality. - Page 2 LAN Cable (Not Supplied) If Pure High-throughput (Greenfield) 802.11n mode is selected and the Encryption type is set to WEP, TKIP or TKIPAES (WPS2Mixed) for your AP, Samsung TVs will not support a connection in compliance with new Wi-Fi certification specification...