Related Manuals for D-Link DSS-5+
Summary of Contents for D-Link DSS-5+
- Page 1 D-Link DSS-5+ 5-port 10/100 Ethernet Switch Manual Rev. 101404w Building Networks for People...
-
Page 2: Table Of Contents
DSS-5+ ... 9 DSS-5+... 9 UB TO DSS-5+ TO OTHER DEVICES & D PEED UPLEX MOUNTING THE SWITCH ON A WALL... 11 TECHNICAL SPECIFICATIONS... 12 RJ-45 PIN SPECIFICATION ... 14 WARRANTY ... 15 ... 2 ... 2 ... 9 ... 10... -
Page 3: About This Guide
BOUT UIDE Congratulations on your purchase of the D-Link DSS-5+. This device integrates 100Mbps Fast Ethernet and 10Mbps Ethernet network capabilities in one high-performance, easy-to-use solution. Purpose This manual will familiarize you with the DSS-5+ and guide you through the installation process. -
Page 4: Introduction
LAN. If an Ethernet network begins to display symptoms of congestion, low throughput, slow response times, and high rates of collision, installing a switch to a network can preserve much or all of the existing network's cabling and workstation interface card infrastructure, while still greatly enhancing the throughput for users. - Page 5 When two switching nodes are communicating, they are connected with a dedicated channel between them, so there is no contention for network bandwidth with other nodes. As a result, the switch reduces considerably, the likelihood of traffic congestion.
-
Page 6: Features
The DSS-5+ is scalable, allowing two or more DSS-5+s to be cascaded together. Since all ports support 200Mbps, any one of its five ports may be used to cascade to an additional switch to open a Full-Duplex Fast Ethernet pipe. - Page 7 Auto-MDI/MDI-X function supports automatic MDI/MDI-X crossover detection, giving true ‘plug and play’ capability—Crossover or Straight-Through CAT5 cables can be plugged into any port. Nway Auto-negotiation for any port. This allows for auto-sensing of speed (10/100Mbps), providing an automatic and flexible solution for the network.
-
Page 8: Unpacking And Setup
Setup The setup of the DSS-5+ can be performed using the following steps: The power outlet should be within 1.82 meters (6 feet) of the Switch. Visually inspect the DC power jack and make sure that it is fully secured to the power adapter. -
Page 9: Identifying External Components
This green indicator light is on when the DSS-5+ is receiving power; otherwise, it is off. Collision : As collision occur on any port of the Switch it will blink. Collisions are normal in an Ethernet network. 100Mbps Link/Activity, 10Mbps Link/Activity Indicator... -
Page 10: Rear Panel
DSS-5+ 10/100Mb Fast Ethernet Switch Auto MDI/MDI-X Ports: All ports support automatic MDI/MDI-X crossover detection. The AutoMDI/MDI-X function makes it simple to connect to the switch—just plug either a Crossover or Straight-Through CAT5 cable into any port. DC Power Jack: Power is supplied through an external DC power adapter. -
Page 11: Connecting The Switch
DSS-5+. DSS-5+ to other devices The DSS-5+ can be connected to another switch or other devices (routers, bridges, etc.) via a two-pair Category 3, 4, 5 UTP/STP Straight-Through or Crossover cable. -
Page 12: Port Speed & Duplex Mode
Port Speed & Duplex Mode After plugging the selected cable to a specific port, the system uses auto- negotiation to determine the transmission mode, auto-detecting the network speed (10Mbps or 100Mbps) for any new twisted-pair connection. If the attached device does not support auto-negotiation or has auto- negotiation disabled, an auto-sensing process is initiated to select the speed and half-duplex mode is selected. -
Page 13: Mounting The Switch On A Wall
The DSS-5+ can also be mounted on a wall. Two mounting slots are provided on the bottom of the switch for this purpose. Please make sure that the front panel is exposed in order to view the LEDs. Please refer to the illustration below: A.) Mounting on a cement wall... -
Page 14: Technical Specifications
ECHNICAL General Standards Protocol Data Transfer Rate Topology Network Cables Number of Ports Physical and Environmental DC inputs Power Consumption Temperature Humidity Dimensions (W x H x D) EMI: PECIFICATIONS IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet CSMA/CD Ethernet: 10Mbps (half duplex) 20Mbps... - Page 15 Performance Transmission Method: RAM Buffer Filtering Address Table Packet Filtering / Forwarding Rate: MAC Address Learning: Store-and-forward 512Kbits per device 2K entries per device 10Mbps Ethernet: 14,880/pps 100Mbps Fast Ethernet: 148,800/pps Automatic update...
-
Page 16: Pin Specification
RJ-45 P PECIFICATION The following diagram and tables show the standard RJ-45 receptacle/connector and their pin assignments. RJ-45 Connector pin assignment Contact Media Direct Interface Signal Tx + (transmit) Tx - (transmit) Rx + (receive) Not used Not used Rx - (receive) Not used Not used RJ-45 pin assignment... -
Page 17: Warranty
D-Link’s sole obligation shall be to repair or replace the defective Hardware during the Warranty Period at no charge to the original owner or to refund at D-Link’s sole discretion. Such repair or replacement will be rendered by D-Link at an Authorized D-Link Service Office. - Page 18 Expedited shipping is available if shipping charges are prepaid by the customer. D-Link may reject or return any product that is not packaged and shipped in strict compliance with the foregoing requirements, or for which an RMA number is not visible from the outside of the package.
- Page 19 D- Link; Products that have been purchased from inventory clearance or liquidation sales or other sales in which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product. Repair by anyone other than D- Link or an Authorized D-Link Service Office will void this Warranty.
- Page 20 D-Link Corporation/D-Link Systems, Inc., as stipulated by the United States Copyright Act of 1976. Contents are subject to change without prior notice. Copyright© 2002 by D-Link Corporation/D-Link Systems, Inc. All rights reserved. CE Mark Warning: This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.