Page 1
33ML400 37ML400 SERVICE MANUAL SY9T733ML400/ COLOR TELEVISION Chassis No. SN-92 33ML400 37ML400 MODELS In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used.
Page 2
33ML400 37ML400 Ref. No. Part No. Description Code PARTS LIST PACKING PARTS PARTS REPLACEMENT (NOT REPLACEMENT ITEM) Replacement parts which have these special safety characteristics SPAKC0645MEZZ – Packing Case — identified in this manual; electrical components having such features (33ML400) å...
(EIA, Channel Plan U.S.A.) Color Sub-Carrier Frequency ........42.17 MHz Specifications are subject to change without (Nominal) prior notice. This document has been published to be used for after sales service only. SHARP CORPORATION The contents are subject to change without notice.
32L-S400, 36L-S400 CL32S40, CL36S40 IMPORTANT SERVICE SAFETY PRECAUTION Ë Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the servicing guidelines which follow: WARNING X-RADIATION AND HIGH VOLTAGE LIMITS 1. For continued safety, no modification of any circuit 1.
Page 5
32L-S400, 36L-S400 CL32S40, CL36S40 IMPORTANT SERVICE SAFETY PRECAUTION (Continued) • Connect the resistor connection to all exposed metal BEFORE RETURNING THE RECEIVER parts having a return to the chassis (antenna, metal (Fire & Shock Hazard) cabinet, screw heads, knobs and control shafts, escutcheon and etc.) and measure the AC voltage Before returning the receiver to the user, perform drop across the resistor.
Page 6
32L-S400, 36L-S400 CL32S40, CL36S40 PRECAUTIONS A PRENDRE LORS DE LA REPARATION Ë Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux conseils suivants. AVERTISSEMENT LIMITES DES RADIATIONS X ET DE LA HAUTE TENSION 1.
Page 7
32L-S400, 36L-S400 CL32S40, CL36S40 PRECAUTIONS A PRENDRE LORS DE LA REPARATION (Suite) • Toucher avec la sonde d'essai les pièces métalliques VERIFICATIONS CONTRE L'INCEN-DIE ET exposées qui présentent une voie de retour au LE CHOC ELECTRIQUE châssis (antenne, coffret métallique, tête des vis, Avant de rendre le récepteur à...
32L-S400, 36L-S400 CL32S40, CL36S40 INSTALLATION AND SERVICE INSTRUCTIONS Note: (1) When performing any adjustments to resistor controls and transformers use non-metallic screwdrivers or TV alignment tools. (2) Before performing adjustments, the TV set must be on at least 15 minutes. HIGH VOLTAGE CHECK CIRCUIT PROTECTION The receiver is protected by a 5.0A fuse (F701),...
Page 10
32L-S400, 36L-S400 CL32S40, CL36S40 For adjustments of this model, the bus data is converted to various analog signals by the D/A converter circuit. Note: There are still a few analog adjustments in this series such as focus and master screen voltage. Follow the steps below whenever the service adjustment is required.
Page 11
32L-S400, 36L-S400 CL32S40, CL36S40 DATA SERVICE ADJUSTMENT ITEM ADJUSTMENT CONTENTS NUMBER RANGE INITIAL VALUE PICTURE 00-7F TINT 00-7F COLOR 00-7F BRIGHTNESS 00-7F SHARPNESS 00-3F Must be set to "24" Vert. PHASE 00-07 Must be set to "00" Hor. PHASE 00-1F RF AGC 00-3F Vert.
Page 12
32L-S400, 36L-S400 CL32S40, CL36S40 Ë SERVICE ADJUSTMENT VCO Adjustment White Balance Adjustment 1. Connect a digital voltmeter between pin (44) of IC201 1. Receive a good local channel. and ground. 2. Enter the service mode and select the service 2. Receive a good local channel. adjustment "S03"...
Page 13
32L-S400, 36L-S400 CL32S40, CL36S40 Sub-Brightness Adjustment 3.58MHz Trap Adjustment 1. Receive a good local channel. 1. Receive a good local channel. 2. Make sure the customer brightness control is set to 2. Enter the service mode and select the service center position.
Page 14
32L-S400, 36L-S400 CL32S40, CL36S40 Ë MTS ADJUSTMENT Ë P-IN-P ADJUSTMENT MTS Level Adjustment P-IN-P Y LEVEL Adjustment 1. Feed the following monaural signal to pin (14) of 1. Receive a good local channel. 2. Enter the service mode and select the service IC3001.
32L-S400, 36L-S400 CL32S40, CL36S40 DESCRIPTION OF SCHEMATIC DIAGRAM WAVEFORM MEASUREMENT CONDITIONS: NOTES: 1. Photographs taken on a standard gated color bar 1. The unit of resistance "ohm" is omitted. (K=k Ω =1000 Ω , M=M Ω ) signal, the tint setting adjusted for proper color. The wave shapes at the red, green and blue cathodes of 2.
4. DESCRIPTION in USA: Contact your nearest SHARP Parts Distributor to order. in CANADA: Contact SHARP Electronics of Conada Limited For location of SHARP Parts Distributor, Please call Toll- Phone (416) 890-2100 Free; 1-800-BE-SHARP MARK: SPARE PARTS-DELIVERY SECTION MARQUE: SECTION LIVRAISON DES PIECES DE RECHANGE ç...
GCABB1134MEKA M Rear Cabinet 36L-S400, CL36S40 CCABA1301MES1 M Front Cabinet Ass'y Not Available – Front Cabinet — GCOVA1039MEKA M Cover for R/C HBDGB1010MESA M Badge, "SHARP" JBTN-1105MEKA M Button, Power, Vol-up/down, CH-up/down GCABB1137MEKA M Rear Cabinet SUPPLIED ACCESORRIES TGAN-1006MEZZ M Guarantee Card...
32L-S400, 36L-S400 CL32S40, CL36S40 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PACKING OF THE SET Polyethylene Bag Operation Manual Registration Card Infrared R/C Unit Batteries Polyethylene Mat Buffer Material FRONT Packing Case Use 22 staples fix the packing case.