hit counter script
Toro 22911 Operator's Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Compact Loader
  5. 22911
  6. Operator's manual

Toro 22911 Operator's Manual

Compact utility loaders
Hide thumbs Also See for 22911:
Table of Contents

Advertisement

Quick Links

Download this manual
Form No. 3364-936 Rev A
Vibratory Plow
Compact Utility Loaders
Model No. 22911—Serial No. 310000001 and Up
To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com.
Original Instructions (EN)

Advertisement

Table of Contents
loading

Related Manuals for Toro 22911

Summary of Contents for Toro 22911

  • Page 1 Form No. 3364-936 Rev A Vibratory Plow Compact Utility Loaders Model No. 22911—Serial No. 310000001 and Up To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com. Original Instructions (EN)

  • Page 2: Table Of Contents

    Serial No. The vibratory plow is an attachment designed for use on Toro compact utility loaders to pull flexible pipe and cable into and through soil. It is designed to be used by This manual identifies potential hazards and has...

  • Page 3: Safety

    Safety Gauging Plow Depth..........7 Transporting the Plow .......... 8 Removing the Plow from the Traction Improper use or maintenance by the operator or Unit..............8 owner can result in injury. To reduce the potential Operating Tips ............. 8 for injury, comply with these safety instructions and Maintenance...............

  • Page 4: Stability Ratings

    Stability Ratings WARNING If you do not fully seat the attachment locking To determine the degree of slope you can traverse with pins in the attachment mount plate holes, the the plow installed on a traction unit, find the stability attachment could fall off of the traction unit severely rating for the hill position you want to travel in the injuring the operator or bystanders.

  • Page 5: Vibration Level

    Vibration Level Hand-Arm Vibration Measured vibration level = 7 m/s Uncertainty Value (K) = 2.8 m/s Measured values were determined according to the procedures outlined in EN 1032. 100-4650 Whole Body Vibration 1. Crushing hazard of hand—keep bystanders a safe distance from the machine.

  • Page 6: Product Overview

    Important: Always use the traction unit to lift and move the attachment. Installing a Blade Toro offers several different blades and pullers. Purchase a blade and puller from your Toro dealer. Figure 3 WARNING 1. Vibratory plow body 4. Gauge rod assembly The blade is sharp and can swing during 2.

  • Page 7: Plowing

    Plowing CAUTION 1. Move the lynch pins to the outside holes on the When plowing on a hill, the plow can swing spring rods to allow the plow to move from side down hill when raised out of the soil. Due to to side (Figure 5).

  • Page 8: Transporting The Plow

    Removing the Plow from the Traction Unit Refer to your traction unit Operator’s Manual for complete instructions on removing attachments from the traction unit and disconnecting hydraulic hoses. 1. With the plow raised above the ground, stop the engine. 2. Remove the lower click pin and clevis pin securing the blade to the plow (to completely remove the Figure 7 blade, remove both the upper and lower click and...
  • Page 9 Figure 9 1. Hairpin cotters • To reduce wear on the traction unit drive chain (if your model has one), tighten the chain so there is only 2 inches (5 cm) of slack on the upper span (refer to your traction unit Operator’s Manual for instructions).

  • Page 10: Maintenance

    Maintenance Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Grease the plow. Before each use or daily • Check the gear lube level. Every 25 hours • Change the gear lube. Every 200 hours • Grease the plow. • Check the gear lube level. Before storage •...

  • Page 11: Servicing The Gear Lube

    Changing the Gear Lube Service Interval: Every 200 hours 1. Position the traction unit and plow on a level surface and lower the attachment lift so that the plow is on the ground. 2. Stop the engine and remove the key. 3.

  • Page 12: Storage

    Storage 1. Before long term storage, wash the attachment with mild detergent and water to remove dirt and grime. 2. Grease the plow. 3. Check gear case lubrication. 4. Check and tighten all bolts, nuts, and screws. Repair or replace any damaged or worn part. 5.

  • Page 13: Troubleshooting

    Troubleshooting Problem Possible Cause Corrective Action The plow does not operate. 1. The hydraulic coupler is not completely 1. Check and tighten all couplers. connected 2. A hydraulic coupler is damaged. 2. Check the couplers and replace any that are damaged. 3.
  • Page 14 Notes:...
  • Page 15 Notes:...
  • Page 16 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor’s service or have difficulty obtaining guarantee information, contact the Toro importer.

Table of Contents