Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
1.1.
ELECTRICAL SAFETY
FWARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other
connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices.
A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a Residual Current
Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply which is not protected
by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1. The Electricity at Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2.
and use a Portable Appliance Tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all
connections to ensure that none is loose.
1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7. DO NOT pull or carry the appliance by the power cable.
1.1.8. DO NOT pull the plug from the socket by the cable.
1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When an ASTA/BS approved UK
3 pin plug is damaged, cut the cable just above the plug and dispose of the plug safely.
Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer insulation
extends beyond the cable restraint and that the restraint is tight.
Double insulated products, which are always marked with this symbol
To rewire, connect the wires as indicated above - DO NOT connect either wire to the earth terminal.
1.1.10. Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure that a
suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket with your electrician.
1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance
plugged into it will be protected. The cable core section is important and should be at least 1.5mm
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use of
2.5mm
section cable. If extension reel is to be used outdoors, ensure it is marked for outdoor use.
2
1.2.
GENERAL SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
F
Familiarise yourself with the application and limitations of the product, as well as the specific potential hazards peculiar to the polisher.
!
WARNING! Disconnect from the mains power before changing accessories, servicing or performing any maintenance.
F
WARNING! Disconnect from the mains power and ensure the disc is at a complete standstill before changing accessories, servicing or
F
performing any maintenance.
Maintain the polisher/sander in good condition (use an authorised service agent).
!
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be
!
dangerous and will invalidate the warranty.
WARNING! Keep all guards and holding screws in place, tight and in good working order.
F
Check regularly for damaged parts.
A guard or any other part that is damaged must be repaired/replaced before the tool is next used.
Locate polisher/sander in a suitable working area, keep area clean and tidy and free from unrelated
!
materials. Ensure there is adequate lighting.
Keep the polisher/sander clean for best and safest performance.
!
Before each use check all abrasive attachments for condition. If worn or damaged replace immediately.
!
Ensure there are no flammable or combustible materials near the work area.
!
WARNING! Wear approved safety eye protection, ear defenders and, if dust is generated,
F
respiratory protection.
INSTRUCTIONS FOR:
POLISHER -
SANDER/POLISHER -
, are fitted with live (brown) and neutral (blue) wires only.
ER1800PD
ER2000PD
Yellow & Green
Earth Wire
Blue
Neutral
Wire
FUSE RATING 13 AMP
, but to be absolutely sure that the
2
ER1800PD/2000PD - 4 - 190503
Brown
Live
Wire
Cable
Restraint
Advertisement
Related Manuals for Sealey ER1800PD
Summary of Contents for Sealey ER1800PD
- Page 1 Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply which is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer.
- Page 2 INTRODUCTION The ER1800PD Heavy Duty polisher is a single speed unit with hardened bevel gears and tough outer casing. Features stop-lock spindle for simple pad/disc loading and unloading. Trigger type power operation with power lock control. Supplied with 170mm backing pad and side handle.
- Page 3 6.2. The motor brushes must only be changed by an authorised Sealey service agent. 6.3. After each 500 hours of use gear head grease should be replaced, by an authorised Sealey service agent. DECLARATION OF CONFORMITY Declaration of Conformity Heavy Duty Polisher - ER1800PD...