Samsung SHS-H505 - Digital Door Lock Manual

Convenient Opening

• User friendly access with cards and password

Graphic Interface

• Shows the operation status of the doorlock

Double Authorization

• Requires card & password combination to open

Double Locking

• Prevents opening from outside (Do not disturb)

Built-in Fire Detection

• Generates alarm in case of a fire

Security Function

• Prevents intrusion from the outside

www.samsungsds-nss.com/en

Safety Cautions

This section contains important information to ensure the user's safety and prevent potential damage to property. Please, read this section carefully and use the product accordingly.

• The user shall not install or repair the product without authorization.
• Do not install the product in the place where the gap between the door and the frame is 5mm or more.
• Make sure that no unauthorized person has the access to the password.
• Do not operate the product with wet hands, and keep liquids such as water or drinks away from the product, or the product may malfunction or be damaged.
• Do not use the excessive force or sharp objects to push the lockbuttons, as this can damage the product.
• Make sure that the door is completely closed when going outside. The manufacturer does not assume the responsibility for any harm caused by engagement of the lock on an improperly closed door.
• Please do not hang on the product or pull it.
• Be sure to correctly match the poles (+/-) when installing the batteries. Install the batteries with the correct poles (+/-).
• Replace all batteries immediately after they run out of power, and never mix new batteries with used ones.
• Do not use water, benzene or alcohol when cleaning the product, as these fluids can cause product malfunction.
• Replace the batteries within 1 week after the battery replacement alarm sounds.

※ In order to safely use the product, please read "Safety Precautions".

※ The features of this product and the contents of the user guide may be changed without notice for quality improvement.

Product Components

The product components used may vary depending on the installation environment.

Key Tag
Key tail
User Manual
'AA' Batteries (LR6)
Emergency Key(5EA)
Handle Shaft
Handle Shaft Spring

• Support Panel and Inner Body Fastening Bolts
• Support Panel and Outer Body Fastening Bolts
• Inner Fastening Bolts
• Strike Fastening Bolts

Outer Body Parts

Inner Body Parts

Mortise

Menu Table

Initialization

Registration

Deletion

Other function

Opening the Door from Outside with a Password

When purchased, the product is set to Multi-leveled Security Code Entry Mode initially. Please refer to "Multi-leveled Security Code Entry Mode setting" for Common Mode setting.

※ Silent Mode
Before entering the password, press the [] button and enter the password, then both the sound of the key entering and the door opening will be suspended. It is a useful function if you do not want to disturb neighbors when you go in and out at night.

Touching [Number Pad] will light up the number pad.

When two arbitrary buttons are lighted, press the buttons in order.

When the numbers on the number pad are lighted, enter the password and press the [] button.

Success: DING DONG DENG
Fail: DING DONG DING DONG

• If the security mode is changed as 'common mode', second step will be skipped.

Note

• Password must be entered after the light is on, and if does not, touch [Number Pad] and re-enter.
• To cancel, press [] button and re-enter.
• If the password is wrong 5 times, "peep" warning alarm will sound 20 times and the system will shut-down for about 3 minutes. When malfunction happens, "beep" will sound every 10 seconds, and stop mode will be turned off automatically after 3 minutes with multiple 'beeps'.

Opening the Door from Outside with a Card or Key Tag

The door can be opened from outside using a card or key tag. Place the registered card or key tag on the card reader.

1. Touch [Number Pad]
   
   Touching [Number Pad] will light up the number pad.
2. Placing the Card or Key Tag on the Card Reader
   
   Success: DING DONG DENG
   Fail: DING DONG DING DONG
   Place the card or key tag on the card reader. The door will be opened after 1 second.

Opening the Door from the Inside

Pulling down the Door Lock Handle

Rotate the door lock handle of the inner body downward.

Rotating the Manual Open/Close Lever to the Right or Left

Rotate the manual Open/Close lever to the right or left to lock the door or release the locking.

Closing the Door from the Inside

Closing the Door from the Inside

The door is automatically locked 2 seconds after the door is closed.

In the Manual Locking Mode

The door is locked when the [Close] button is pressed, or the manual Open/Close lever is rotated.

Initialization (Password, Card, Key Tag)

All registered data (password, card, key tag) are deleted. After initialization, the password is set to '1234', and the registered card, key tag data are erased. Please register a new password after initialization.

1. Pressing the [Register] Button (from the inside)
   
   Press and hold the [Register] button for 5 seconds
2. Entering the Numbers for Initialization (from the outside)
   
   When the number pad is lighted, enter '4560852580' and then press the [] button.

Password Change

The password can be 4~12 digits number. Only one password can be registered.

1. Pressing the [Register] Button (from the inside)
   
   Press the [Register] button briefly.
2. Entering the Current Password (from the outside)
   
   Enter the current password when the number pad is lighted, and press the [] button.
3. Entering a New Password (from the outside)
   
   Enter the new password (4 to 12 digits) and press the [] button.
4. Checking New Password Operation (from the outside)
   
   To make sure the password has been properly registered, check the new password and close the door.

• Manage your password with care so that unauthorized people will not have access to it. Regularly changing your password can reduce the risk of it being leaked.

Card and Key Tag Registration

Up to 30 cards, including the key tag and user password, can be registered.

1. Pressing the [Register] Button (from the inside)
   
   Open the battery cover of the inner body and briefly press the [Register] button.
2. Entering the Current Password (from the outside)
   
   Enter the current password ('1234' after initialization) when the number pad is lighted, and press the [] button.

[Card and Key Tag Registration Without ID number]

3. Placing the Card or Key Tag on the Card Reader (from the outside)
   
   Place the card or key tag to be registered on the card reader of the outer body. You will know the card or key tag has been registered when "DING DONG DENG" sounds.
4. Confirming Card or Key Tag Registration (from the outside)
   
   Place the registered card or key tag to the card reader on the outer body

• To register multiple cards or key tags, lightly place another card or key tag to the card reader within 20 seconds after registering the previous card or key tag.
• ID number is given automatically in order of the registration.

[Card and user password registration with ID number]

3. Enter 2 digits ID number
   
   Input ID between 01 and 30, and press [Ü].
4. Enter new user password
   
   Enter new user password(4 to 12 digits) and press [].
   OR
   Placing the Card or Key Tag on the Card Reader (from the outside)
   
   Place the card or key tag to be registered on the card reader of the outer body. You will know the card or key tag has been registered when "DING DONG DENG" sounds.
5. Confirming Card or Key Tag Registration (from the outside)
   
   Place the registered card or key tag to the card reader on the outer body.

• User password is only for the user, so other functions such as registering cards are not available with this password.
• One ID has only one password or card.

Deleting Registered Cards

You can delete individual or all registered cards.

1. Pressing the [Register] Button (from the inside)
   
   Press the [Registration] button for 3 seconds.
2. Entering the Current Password (from the outside)
   
   Enter the current password when the number pad is lighted, and press [] button.
3. [Deleting Cards]
   Reading the card to be deleted
   
   If you want to delete all cards data, press [88] + [] after step 2.
   OR
   [Deleting ID information]
   Enter ID number to delete
   
   Enter 2 digits ID number, then the card or user password of it will be deleted.

Double Authorization Mode Setting

Double authorization mode requires both card and password to open the door, ensuring more security.

Briefly press the [Register] button on the inner body.

Press the [] button after pressing the [4] or [6] button, and the authorization mode will be set.

Note

• The setup of double authorization mode only works when the door is open.
• When purchased, the product is not set to double authorization mode initially.
• To setup the double authorization mode, more than 1 card must be registered.
• Double authorization mode will automatically be turned off when all cards are deleted.

Automatic/Manual Locking Setting

The Automatic Locking mode allows for automatic locking of the door when it is closed.

Set the [Automatic/Manual Locking] toggle switch of the Inner Body to the 'A'/'M' position.

• Automatic: The door is automatically locked 2 seconds after being closed.
• Manual: The door does not lock automatically, and [CLOSE] button must be pressed from the inside, touch [Number Pad] to close the door.

Intrusion Detection Function

This function generates the alarm sound when an attempt is made to forcefully open the door from the inside or the outside.

(This is a basic function of the lock, and cannot be separately set or released.) If the door is forcefully opened while locked, the door opening sensor detects it and generates the alarm sound.

Sound Setting and Releasing

The sound that is generated when the number buttons are pressed, when the door is locked or when the locked door is unlocked, can be set according to the user's preference. The product is set to generate all sounds at the factory.

Open the battery cover on the inner body.


Put the [Sound Control] switch on one of [0], [1], or [2], and close the battery cover.
[0]: Mute [1]: Normal [2]: Loud

Multi-leveled Security Code Entry Mode Setting

You can set the security mode suitable for your use when you open the door using a password.

Briefly press the [Register] button on the inner body.

Press the [] button after pressing the [7] or [9] button, and the security mode will be set.

Setting the Double Locking

The double locking function prevents opening of a locked door from outside.

Setting Double Locking

Press the [Close] button for 2 seconds or longer from the inside while the door is locked.

Activating Double Locking

Inside: The double locking sound is generated when the [Close] button is pressed.

Outside: The double locking sound is generated, the double locking display LED is lighted, and the door cannot be opened when touch [number pad], or a card is applied.

Releasing Double Locking

The double locking function is released when the inner body handle is rotated downward, or the manual Open/Close lever is rotated to the right or left.

Setting the Security Function

Setting the Security Function

1. When the door is closed [] of the outside body's number pad will light up.
2. Press and hold the [] button on the outer body for 3 seconds while the door is locked.

Releasing the Security Function

After touching the Number Pad, contact a registered card, or enter the password and then press the [] button.

Note

• The security function is automatically released when the locked door is opened from outside by entering the registered password or applying the card or key tag to the card reader.

Alarm Sound (Prank Prevention Function)

This function generates an alarm sound and deactivates lock operation when it is improperly handled from the outside.

This alarm will sound if an attempt is made to open the door with an invalid card, or if a wrong password is entered five times in a row.

The alarm sound is generated, and the lock is deactivated for 3 minutes. While the door is in this inactive mode, a single "DING" sound is generated every 10 seconds and seven consecutive "DINGS" will sound after 3 minutes. Following this, the lock is released from inactive mode.)

Releasing the Alarm

Inside Press the [Register] button.

Outside Get a registered card authorized or enter the password and then press the [] button.

Replacing the Batteries

Battery Replacement Alarm Generation

If the melody of "Blues for Elise" sounds when opening the door with the password or a card (key tag), it is time to replace the batteries. (The low battery indicator is lighted when the melody sounds.)

Replacing the Battery

Replace all 8 batteries within a 1 week of the first alarm sound.

• If the poles of the batteries are not placed properly, the lock will not operate normally.
• Liquid leaks from batteries can damage the product. Check the batteries regularly (every 6 months).
• After the battery replacement alarm has sounded, password/card information cannot be registered, changed, deleted, initialized or configured until the batteries are replaced.
• The unit will stop operating suddenly if the batteries are not replaced.

Using the Emergency Battery

If the batteries are not replaced after their replacement time comes, they will be completely discharged and the lock will not operate.

Opening the Door Using an Emergency Battery

Purchase an emergency battery (9V) at the nearest store.

• As the alkaline batteries offer longer life, they are recommended over the manganese batteries or rechargeable ones.

Place the card or key tag on the card reader, or enter the password, while the 9V battery is connected to the external power port of the outer body.

Built-in Fire Detection Function

This function generates the alarm sound when fire is detected so that the residence can quickly respond. The built-in fire detection function is a basic function of the lock, and cannot be released by the user. Fire detection function is operational at about 75 ℃ ± 10 ℃; this can vary depending on the installation environment.

When fire occurs, the temperature sensor detects it and flashes the [Close] button while generating the alarm sound. The door is automatically opened after the alarm sound has stopped. (The lock resumes normal operation if the inside temperature returns to a normal level.) The built-in fire detection function is activated when the temperature rises around 60°C, which may differ depending on the installation environment.

Product Specifications

• The contents of this user guide are subject to change without prior notice to the user in order to enhance performance of the product.