Page 1
FILE NO. 810-200548 SERVICE MANUAL DIGITAL VIDEO DVD VIDEO RECORDER D-R350SB May, 2005...
Page 2
LASER BEAM CAUTION LABEL When the power supply is being turned on, you may not remove this laser cautions label. If it removes, radiation of a laser may be received. PREPARATION OF SERVICING Pickup Head consists of a laser diode that is very susceptible to external static electricity. Although it operates properly after replacement, if it was subject to electrostatic discharge during replacement, its life might be shortened.
CONTENTS SECTION 1 GENERAL DESCRIPTIONS 2. LOCATION OF MAIN PARTS 1. OPERATING INSTRUCTIONS 2-1. Location of Main Parts 2-2. Location of PC Boards SECTION 2 PART REPLACEMENT AND ADJUSTMENT PROCEDURES 1-2. PC Board Replacement 1. REPLACEMENT OF MECHANICAL PARTS 1-2-1. Digital PC Board 1-1.
SECTION 1 GENERAL DESCRIPTIONS 1. OPERATING INSTRUCTIONS Please refer to the owner's manual about the contents.
Page 5
2. LOCATION OF MAIN PARTS 2-1. Location of Main Parts RAM1 RAM DRIVE ZG45 FAN Fig. 1-2-1 2-2. Location of PC Boards EU05 Mother PC board EU01 Digital PC board EU02 Power PC board EU03B Front (L) PC board EU56 Front (LED) PC board EU55 Front Jack PC board EU03A Front (R) PC board...
SECTION 2 PART REPLACEMENT AND ADJUSTMENT PROCEDURES CAUTIONS BEFORE STARTING PART REPLACEMENT Electronic parts are susceptible to static electricity and may easily damaged, so do not forget to ground as required. Many screws are used inside the unit. To prevent the screws from missing or dropping, etc. always use a magnetized screwdriver in servicing.
1-1-2. Front Panel 1. Remove the top cover. (Refer to item 1-1-1.) 2. Remove the Digital PC board. (Refer to item 1-2-1.) 3. Disconnect three connectors (1). 4. Remove two screws (2) and four claws, then remove the front panel (3). Connector (1) Connector (1) Connector (1)
1-1-4. Rear Panel 1. Remove the top cover. (Refer to item 1-1-1.) 2. Peel of the tape (1). 3. Remove two screws (2) and seven screws (3). 4. Remove two claws, then remove the rear panel (4). 5. Remove two screws (5), then remove the fan (6). Note: •...
Page 9
1-2. PC Board Replacement 1-2-1. Digital PC Board 1. Remove the top cover. (Refer to item 1-1-1.) 2. Disconnect the flexible cable (1). 3. Remove four screws (2), then remove the Digital PC board (3). Note: • The Digital PC board (3) is connected to the Mother PC board (4) by three connectors (5). Take notice when removing. Flexible cable (1) Flexible...
Page 10
1-2-2. Mother PC Board 1. Remove the rear panel. (Refer to item 1-1-4.) 2. Remove the Digital PC board. (Refer to item 1-2-1.) 3. Disconnect three connectors (1). 4. Remove five screws (2) . 5. Pull out the Mother PC board (3) toward the rear side (indicated by the arrow). Screws (2) Connector (1) Connectors (1)
Page 11
1-2-3. Power PC Board 1. Remove the RAM drive. (Refer to item 1-1-3.) 2. Disconnect four connectors (1). 3. Remove four screws (2), then remove the Power PC board (3). Connectors (1) Connector (1) Screws (2) Connector (1) Power PC board (3) Fig.
Page 12
1-2-4. Front (R), Front (L), Front (LED) and Front Jack PC Boards 1. Remove the front panel. (Refer to item 1-1-2.) 2. Peel off the tape (1). 3. Remove four screws (2), then remove the stay (3). 4. Remove four screws (4) and two screws (5), then remove the Front (R) PC board (6) and Front (LED) PC board (7). 5.
Page 13
2. WIRING CONNECTION DIAGRAM After the servicing is complete, return the wiring to its original state by using the diagram below as a reference. Mother PC board Power PC board Digital PC board W051 W102 W101 Front panel W104 RAM drive W801 : Tape : Flexible cable...
SECTION 3 SERVICING DIAGRAMS 1. CIRCUIT SYMBOLS AND SUPPLEMENTARY EXPLANATION 1-1. Precautions for Part Replacement • In the schematic diagram, parts marked (ex. • Using the parts other than those specified shall violate the regulations, and may cause troubles such as F801) are critical part to meet the safety regulations, operation failures, fire etc.
Page 18
SECTION 4 PARTS LIST SAFETY PRECAUTION The parts identified by ! ( ) mark are critical for safety. Replace only with part number specified. The mounting position of replacement is to be identical with originals. The substitute replacement parts which do not have the same safety characteristics as specified in the parts list may create shock, fire or other hazards.
Page 19
1. EXPLODED VIEWS 1-1. Packing Assembly Z031 Z032 Z033 Z002 Z001 Z001A Note: A clamp filter (Z001A) is attached to a power cord (Z001). Refer to the figure below for the installation. Power supply cable Turn the power supply cable 2 round in the clamp filter.
Page 26
SPECIFICATIONS Power requirement during operation Power requirement at standby 3.1W Power supply 230V AC, 50Hz Mass 3.4kg External dimension Width 430 x Height 58 x Depth 325mm Tuner System: Frequency synthesizer Channel coverage: PAL l VHF: A-J, 11, 13, E2-E12 UHF: E21-E69 CATV: X, Y, Z,S1-S41,1-53 (48MHz to 464MHz, 8MHz steps)
Page 27
1 1, SHIBAURA 1 CHOME, MINATO KU, TOKYO 105 8001, JAPAN...
Page 28
FILE NO. 810-200548 SERVICE MANUAL DIGITAL VIDEO DVD VIDEO RECORDER D-R350SB May, 2005...
3. BLOCK DIAGRAMS 3-1. Overall Block Diagram Digital UNIT Audio LPF IC305 DVD RAM/RW Drive 6bit EEPROM ICX01 IC540 IC901 AUDIO Optical CV/SRGB in D/A Converter Digital out UPD61 75F1 PCM 755 AUDIO OUT AUDIO IN L/R FRAME SYNC 64M+32M ENCODE FLASH ROM ENCRIPT...
Page 30
4. CIRCUIT DIAGRAMS 4-1. Power Supply Circuit Diagram IC801 (Drain - GND) ON - MODE AC240 50Hz IN Ch1 - (Drain - Source) V = 100V / div H = 10us / div Fig. 3-4-1...
Page 31
• Table of the Terminal Voltage of the Power Supply Circuit Conditions : AC240V 50Hz IN IC801 IC821 IC822 PIN No, 5.85V 14.58V 2.49V 4.18V 17.36V 5.84V 14.33V 2.47V 4.23V 13.68V 4.42V 11.99V DVD-PLAY 5.84V 14.33V 2.47V 4.23V 13.68V 4.42V 11.99V IC823 IC824...
5-2. Front Jack PC Board Fig. 3-5-3 EU55 Front Jack PC Broad (Top side) Fig. 3-5-4 EU55 Front Jack PC Broad (Bottom side) 5-3. Front (L) PC Board Fig. 3-5-5 EU03B Front (L) PC Broad (Top side) Fig. 3-5-6 EU03B Front (L) PC Broad (Bottom side)
Page 52
5-4. Front (R) PC Board Fig. 3-5-7 EU03A Front (R) PC Broad (Top side) Fig. 3-5-8 EU03A Front (R) PC Broad (Bottom side)