CRAFTSMAN CMXZDCG440 - Wireless Keypad with All Weather Cover Manual

INTRODUCTION

Compatible with garage door openers manufactured after January 1, 1993. Make sure the garage door opener has a working light bulb because it is a programming indicator.
Install the battery and program the keypad prior to installation.

This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

REFER TO GARAGE DOOR OPENER MANUAL FOR DETAILED INSTALLATION, ADJUSTMENTS, AND SAFETY INFORMATION.
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:

• Install keypad within sight of the garage door, out of reach of children at a minimum height of 5 feet (1.5 m), and away from ALL moving parts of door.
• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote controls.
• Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.

PREPARE

Locate the Learn button on the garage door opener.

NOTE: Your garage door opener may look different.

OR

OR

PROGRAM INITIAL PIN

1. Press and hold the * and # buttons until the lights on the keypad stop blinking.
   
   
2. Enter a 4-digit personal identification number (PIN) of your choice:
   ? ? ? ?
   Then press the # button.
   
   
3. Press and release the Enter button on the keypad a number of times that corresponds with the garage door opener type:

   # of Presses	Garage Door Opener Type
   1	Security+ 2.0® (Yellow Learn Button)
   2	Security+® (Purple Learn Button)
   3	Security+® (Red/Orange Learn Button)
   4	Billion Code (Green Learn Button)

   
   
   
4. Once the garage door opener type is selected, press the 0 button.
   
   
5. Press and release the Learn button on the garage door opener.
   
   The Learn LED will light. Within 30 seconds...
   
6. Enter your 4-digit PIN, then press and release the ENTER button until the garage door opener lights flash or two clicks are heard.
   
   
7. To test, enter your PIN, then press the ENTER button.
   
   The garage door opener will activate.

To program the keypad to more than one garage door opener, repeat the steps above using a new PIN for each additional garage door opener.

CHANGE AN EXISTING PIN*

1. Press the programmed PIN that you want to change.
   
   
2. Press and hold the # button until...
   
   ...the light bulb blinks twice.
   
3. Enter the new 4-digit PIN of your choice, then press the ENTER button:
   
   The light bulb will blink once:
   
   
4. To test, press the new PIN, then the ENTER button. The garage door opener will activate.
   

* For garage door openers that have a green Learn button or an external receiver repeat "Program Initial PIN" to change the existing PIN.

PROGRAM A TEMPORARY PIN

NOTE: This feature is not available on garage door openers that have a green Learn button or an external receiver.

A temporary 4-digit PIN can be programmed to allow access to visitors. Each programmed PIN can program one temporary PIN. The temporary PIN can be set for a number of hours or a number of door openings. The temporary PIN cannot be the same as any previously programmed PIN.

1. Press any programmed PIN, then press and hold the * button until...
   
   ...the light bulb blinks 3 times.
   
2. Enter the temporary 4-digit PIN of your choice, then press the ENTER button.
   
   The light bulb will blink 4 times.
   
3. NUMBER OF HOURS
   Press the number of hours the temporary PIN will work (up to 255).
   +
   Then press the * button.
   

OR

3. NUMBER OF OPENINGS
   Press the number of openings the temporary PIN will work (up to 255).
   +
   Then press the # button.
   

To test, press the temporary PIN, then press the ENTER button. The garage door opener will activate. If the temporary PIN was set for a number of openings, the test will use up one opening.

To clear the temporary PIN, repeat steps 1-3 above, setting the number of hours or openings to 0 in step 3.

INSTALLATION

1. Select a location to mount the keypad at a minimum height of 5 feet (1.5 m) out of the reach of children.
2. Remove battery cover and battery.
3. Mark the top mounting hole and drill 1/8 inch (3.2 mm) pilot hole.
4. Install the top screw, allowing 1/8 inch (3.2 mm) to protrude above the surface. Position the keypad over the top screw.
5. Mark the bottom hole and drill 1/8 inch (3.2 mm) pilot hole. Install the bottom screw. Do not overtighten to avoid cracking the plastic housing.
6. Reinstall battery and replace cover.
   

OPERATION

The garage door opener activates when the PIN and ENTER button are pressed. The keypad will blink for 15 seconds, during that time the ENTER button can be used to stop, start or reverse the door.

If the wrong number is accidentally pressed, press the correct PIN then the ENTER button. The keypad will transmit only the last four digits that were pressed before the ENTER button.

ONE BUTTON CLOSE: The keypad has a feature that allows the door to be closed using the ENTER button instead of a PIN.

NOTE: This feature is not available on garage door openers manufactured prior to 2006 or an external receiver.

To deactivate the one button close feature:

1. Press and hold the 1 and 9 buttons for 10 seconds.
2. The keypad will blink four times when the one button close feature is deactivated.

To activate the one button close feature:

1. Press and hold the 1 and 9 buttons for 10 seconds.
2. The keypad will blink twice when the one button close feature is activated.

REPLACEMENT PARTS

9V Battery: 10A25
Keypad cover: 41D621
Battery cover: 41D541

BATTERY

To prevent possible SERIOUS INJURY or DEATH:

• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.

Replace the battery when the keypad becomes dim or does not light after a button is pressed. Dispose of old battery properly.

NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

This device complies with Part 15 of the FCC rules and IC RSS-210. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

Call: 888-331-4569
www.craftsman.com

Documents / Resources

References

• http://www.p65warnings.ca.gov
• Home | CRAFTSMAN® | CRAFTSMAN

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download CRAFTSMAN CMXZDCG440 - Wireless Keypad with All Weather Cover Manual