Advertisement
Quick Links
ADP 6830
Programme selection button
On / Off button
Start button
Switches "on" when the dishwasher is
operating. Flashes when a fault occurs.
Switches off at the end of the programme.
Indicators
Add regeneration salt
Only add regeneration salt immediately
before starting a wash programme.
Add rinse aid
Programmes
Sensor Normal
Sensor Intensive
Pre-Rinse
Glass
Quickwash
Normal
1)
Reference programme for energy label in compliance with
EN 50242 regulations;
2)
Refer to "User instructions";
3)
Program data obtained in conformity with European
standard EN 50242. Values may vary in relation to usage,
e.g.: different loads, water temperatures - above or below
15°C - as well as water hardness and power supply
voltage, etc.
Important information for Test Laboratories:
For detailed information on the EN comparison test and other tests, contact the following address:
"nk_customer@whirlpool.com".
Whirlpool is a registered trademark of Whirlpool USA
Before using the dishwasher, read the user instructions!
Quick Reference Guide
Programme chart
Automatic programme recommended
5)
40-55°C
for routine washes, with no dried-on or
burnt food (not for EN 50242).
Automatic programme recommended
5)
for heavily soiled crockery with dried-
60-70°C
on or burnt food, for example pans and
saucepans.
cold
Crockery to be washed later.
Light soiling, for example glasses and
40°C
cups.
Lightly soiled crockery with no
40°C
dried-on food.
1) 5)
50°C
Normally soiled crockery.
Options
Time and failure display
Indicates in hours the time remaining until the start
of the wash cycle. Switches off when the
programme starts and indicates the time remaining
in hours and minutes.
"F ...." Identification of faults for service technician
"Delayed start" button
The wash cycle can be programmed to start after
1 - 24 hours. With each successive touch of the button,
the delayed start indicator increases by 1 hour, and
after 24 returns to 00. Then press the Start button.
The dishwasher will start at the set time.
Antibacterial rinse
This function adds an antibacterial rinse at the end of
the wash cycle, thereby guaranteeing a perfectly clean
and sanitized load. The lamp will light up when the
function is activated. If the temperature is not
maintained during the antibacterial cycle (e.g. if the
door is opened and remains open for a long time), the
lamp will start blinking to indicate that sanitation is
not guaranteed.
Detergent
Loading instructions
A
4)
The bacteria removal efficiency has been tested by the
Institut Pasteur de Lille (France), based on the NF
EN 13697 standard of November 2001.
5)
These programmes can be used with the Antibacterial
rinse option.
(We reserve the right to make technical modifications)
3)
4)
2)
Consumption
B
Litres
kWh
X
X
10.0-13.0 0.80-1.05
X
X
13.0-20.0 1.10-2.00 100-150
-
-
4.0
0.03
X
-
10.0
0.80
X
-
10.0
0.65
X
X
13.0
1.05
5019 396 91503
WH/I/B/GB
GB
3)
Minutes
60-120
14
55
30
120
Advertisement
Related Manuals for Whirlpool ADP 6830
Summary of Contents for Whirlpool ADP 6830
- Page 1 Important information for Test Laboratories: For detailed information on the EN comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”. 5019 396 91503 Whirlpool is a registered trademark of Whirlpool USA (We reserve the right to make technical modifications) WH/I/B/GB...
- Page 2 How to use the appliance Further indications are given in the single chapters and in the user instructions. Switch on the appliance Press the ON / OFF button. Compartment A: With each wash cycle. Fill the detergent dispenser Compartment B: For programmes with pre-wash only.
- Page 3 Dishwasher loading instructions and racks provided depending on the model Upper rack: Crockery holder (A): Depending on the position, for long-handles utensils, cups and plates. Glass holder (B): Long-stemmed glasses. Long-handled utensils (e.g. carving forks, knives) must be arranged with the sharp end facing in towards the appliance.
- Page 4 What to do if... If a fault occurs, before contacting our After-Sales Service, make the following checks to try and remedy the problem (* see also the corresponding chapter in the user instructions). Problem Cause Remedy The appliance is not •...