Advertisement
Quick Links
PREFACE
Thank you for buying Navis anemometer sensor. This manual provides information for the best performance and safe application of the
WS and WSD wind sensors. This manual does not cover the receiver/display unit, for which the manuals will come separately.
Read this manual carefully before starting the installation of the sensors. Keep this manual after installation for future reference.
Sensors are compatible with all actual NAVIS 868MHz display/receiver units: W410, W301, WL11, WL12, WR3B, W110, ...
PRODUCT LAYOUT (exploded view)
4.
1.
3.
2.
5.
Figure 1. WS sensor
ASSEMBLY
The sensor is supplied with a battery inserted and is ready for installation.
Before installation insert the cups on sensor. Place the cups on axe and
press the center part with moderate force to end position. To remove
the cups, grab them in the center part and pull from the
axle with moderate force.
WSD sensor - attaching the aluminum rod holder (Figure 3.):
1. Insert the aluminum holder into opening on sensor (step 1).
2. Insert (step 2) the screw into the assembly hole.
Check and adjust vertical alignment between sensor body
and aluminium tube (step 3).
3. Tighten (step 4) the screw into the assembly hole.
INSTALLATION
WS and WSD sensors to be mounted on 20 mm diameter vertical pool
as shown on Figure 4.
At WSD sensor turn the N mark to Nord.
Calibrating of North is possible also after installation, on display unit.
Mount sensor to highest possible position with unobstructed air flow.
Use self-leveling mounting assembly (optional) if vertical sensor position
can't be ensured with vertical holder (for example at mobile cranes).
For maximum range there should be a clear and unobstructed line of sight
between the sensor and antenna of display/receiver unit.
WIRELESS WIND SPEED / DIRECTION SENSOR
WS 010-1 (wind speed sensor, standard range)
WS 011-1 (wind speed sensor, extended range)
WSD 010-1 (wind speed/direction sensor, standard range)
WSD 011-1 (wind speed/direction sensor, extended range)
1.
3.
2.
6.
Figure 2. WSD sensor
MANUAL
Models:
4.
7.
8.
5.
1.
Figure 3. WSD sensor assembly
Figure 4. Sensor installation on vertical pool
1.
Wind cups
2.
Wind speed head with bearings
3.
PCB - Electronic driving circuitry
4.
Battery
5.
Sensor main body
6.
Aluminum bottom plug
7.
Wind direction head with bearings
8.
Wind vane
2.
4.
1.
2.
3.
3.
Advertisement
Summary of Contents for NAVIS WS 010-1
- Page 1 PREFACE Thank you for buying Navis anemometer sensor. This manual provides information for the best performance and safe application of the WS and WSD wind sensors. This manual does not cover the receiver/display unit, for which the manuals will come separately.
- Page 2 OPERATION Sensor switches “ON” automatically when the anemometer cups revolve. Wind speed or direction data are continuously measured and fresh data are transmitted every 2 seconds. Auto OFF function: In no wind condition the sensor switches “OFF” 6 hours after the anemometer cups have stopped rotating. Auto OFF can be disabled by the user.
- Page 3 Battery replacement: WS sensor WSD sensor Unscrew the aluminum bottom part by turning it Take off the cups (step 1). Unscrew the upper head with bearings by turning anticlockwise (step 1). Pull out the PCB with the it anticlockwise (step 2). Pull out the PCB with the battery (step 3) and insert battery (step 2) and insert a new battery (1x 3,6V a new battery (1x 3,6V AA Lithium battery).
- Page 4 WARRANTY (LIMITED) The warranty period of NAVIS products is one year after the date of purchase. During limited warranty period any defective product will be repaired or replaced with comparable product without charges. The claimed product will be repaired or replaced only when returned to the store where it was purchased together with original invoice.