Adjusting The Speaker - Sony HT-DDW750 Operating Instructions Manual
Hide thumbs
Also See for HT-DDW750:
- Operating instructions manual (52 pages) ,
- Speakers connection (2 pages) ,
- Manual (51 pages)
Table of Contents
Advertisement
Multi channel surround setup
Adjusting
the speaker
level
(continued)
•
Surround
speaker size (_
xxxxx)
• If you connect
large speakers
that will
effectively
leproduce
bass frequencies,
select
"LARGE".
Normally,
select
"LARGE".
However,
if the fi'ont speakm_
are set to
"SMALL",
you cannot
set the surround
speakers
to "LARGE".
• If the sound
is distorted,
or you IEel a lack of
s/_rround
effects
when
using nmhi
channel
surround
sound,
select
"SMALL"
to activate
the bass redirection
cirofitry
and output
the
s_rround
channel
bass fiequencies
from
the sub
woofer
or other "LARGE"
speakers.
• If you do not connect
surround
speakers,
select
-NO-
.3
Tip
*1 *3 correspond
to the following
Dolby Pro Logic
modes
*1 NORMAL
*2 PHANTOM
*3 3 STEREO
Tip
Internally,
the LARGE
and SMALL
settings
for each
speaker
detelxnine
whether
the internal
sound
processor
will cut the bass signal from that cllannel.
When the bass is cut t¥om a channel,
tile bass
redirection
ch_:uitry
sends tile corresponding
bass
frequencies
to the sub woot_r or other "LARGE"
speakers.
However,
since bass sounds
have a certain amount
of
directionality,
it is best not to cut [hem, if possible.
Therefore,
even when using small speakers,
you can
set them to "LARGE"
if you want to output the bass
frequencies
from that speaker.
On the other hand, if
you ale using a large speaker,
but prefer not Io have
bass frequencies
output
from that speaker,
set it to
"SMALL".
If the overall
sound level is lower than you pret_21; set
all speakers
to "LARGE".
If there is not enough
bass,
you can use the BASS parameter
in the TONE menu
to boost the bass levels. To adjust the bass, see page
27.
Use tim remote while seated in your listening
position
to adjust the level of each speaker.
Note
The l_ceiver
incorporates
a new test tone with a
frequency
centered
at 800 Hz for easier speaker
level
adjustment,
t
Press
I/_
on the remote
to turn
on the
receiver.
2
Press
TEST
TONE
on the remote.
"T. TONE" appears in the display and you
will
hear the test tone from
each
speaker
in
sequence.
Front (letl)
.-+ Center
"-4 Front
(right)
-+
Surround
(right)
_
Surround
(left)
Sub
woofer
Adjust
the speaker
level
and balance
using
the LEVEL
menu
so that the level
of the test
tone
sounds
the same
from
each
speaker.
For details
on the LEVEL
menu,
see page
26.
While
adjusting,
the test tone
is output
l¥om
the speaker
whose
adjustment
is performed.
4
Press
TEST
TONE
again
to turn
off the
test tone.
Tip
YOU can adjust the level (if all speakers
at the same
time. Press MASTER
VOL +/- on the remote or turn
MASTER
VOLUME
on the receiver.
Notes
• The adjusted
value ale shown
in the display
during
adjustmenh
• Although
these adjustments
can also be made via
the front panel using the LEVEL
menu (when the
test tone is outpul, the receiver switches
to the
LEVEL
menu automatically),
we _commend
you
_llow
the procedure
described
above and adjust the
speaker
levels from your listening
position using the
remote.
18 68
Advertisement
Table of Contents
