Advertisement
Quick Links
Preparing the Machine
1. Park the machine on a level surface.
2. Disengage the PTO (if equipped) and lower the cutting units.
3. Engage the parking brake.
4. Shut off the engine and remove the key.
5. Wait for all movement to stop and allow the machine to cool.
Hot hydraulic fluid can cause severe burns.
Allow the hydraulic fluid to cool before performing any maintenance to the hydraulic
system.
6. Relieve all pressure from the hydraulic system; refer to the Service Manual for your
machine.
Hydraulic fluid escaping under pressure can penetrate the skin and cause injury.
• Ensure that all hydraulic fluid hoses and lines are in good condition and that all
hydraulic connections and fittings are tight before applying pressure to the
hydraulic system.
• Keep your body and hands away from pinhole leaks or nozzles that eject high-
pressure hydraulic fluid.
• Use cardboard or paper to find hydraulic leaks.
• Safely relieve all pressure in the hydraulic system before performing any work on
the hydraulic system.
• Get immediate medical help if fluid is injected into the skin.
7. Remove the hood from the machine; refer to the Operator's Manual for your machine.
© 2024—The Toro
®
Company
8111 Lyndale Ave So
Bloomington, MN 55044
3WD Kit
Reelmaster ® 3105-D or Groundsmaster® 3505-D
Traction Unit
Model No. 03229
Register at
www.Toro.com
Installation Instructions
WARNING
DANGER
Original Instructions (EN)
Printed in the USA
All rights reserved
3463-204A
*3463-204* A
Advertisement
Related Manuals for Toro 03229
Summary of Contents for Toro 03229
- Page 1 3463-204A 3WD Kit Reelmaster ® 3105-D or Groundsmaster® 3505-D Traction Unit Model No. 03229 Installation Instructions Preparing the Machine 1. Park the machine on a level surface. 2. Disengage the PTO (if equipped) and lower the cutting units. 3. Engage the parking brake.
- Page 2 Lifting the Back of the Machine Lift the back of the machine; refer to the Operator’s Manual or Service Manual for your machine. Removing the Rear Wheel and Hub Assembly 1. Remove and discard the 4 lug nuts that secure the wheel to the wheel-hub assembly and remove the wheel from the machine.
- Page 3 Installing the Hydraulic Motor, Hub, and Rear Wheel Parts Required Hydraulic-motor assembly Hydraulic fitting Bolt (1/2 x 2-3/4 inches) Locknut (1/2 inch) Wheel-hub assembly Lug nut Locknut (1-1/2 inches) 1. Secure the hydraulic-motor assembly to the steering fork with 4 bolts (1/2 x 2-3/4 inches) and 4 locknuts (1/2 inch) 2.
- Page 4 5. Slide the wheel hub on the hydraulic-motor assembly . Ensure that the groove in the hub is aligned with the key on the motor. 6. Install the hub locknut (1-1/2 inches) until it is lightly seated against the hub. G495908 7.
- Page 5 Removing the Hydraulic Hose Remove and discard the existing upper hydraulic hose routed between the piston pump and the upper front hydraulic tube G494354 3463-204A Page 5...
- Page 6 Installing the Hydraulic Hoses Parts Required Hydraulic hose (70 inches) Hydraulic hose (129 inches) Clamp Clamp case Bolt (5/16 x 2-3/4 inches) Locknut (5/16 inch) Cable tie Note: Before installing any hydraulic hoses, ensure that the correct O-rings are in position and lubricated with hydraulic fluid.
- Page 7 3. On the rear frame tab on the machine, install the 2 hose clamps and clamp case using 2 bolts (5/16 x 2-3/4 inches) and 2 locknuts (5/16 inch) . Ensure that the hydraulic hoses are routed between the hose clamps as shown. G494604 4.