Advertisement
Quick Links
Catalyst 9300/X/L-M Series Installation Guide
About this Guide
This guide provides instruction on how to install and configure your Catalyst 9300/X/L-M series switches in the Meraki-
managed mode.
Product Overview
Models
Model number
C9300-24T-M
C9300-24P-M
C9300-24U-M
C9300-24UX-M
C9300-48T-M
C9300-48P-M
C9300-48U-M
24 port Gbe Data Only
24 port Gbe Data with 30W PoE+
24 port Gbe Data with 60W UPOE
24 port mGig Data with 60W UPOE
(10G/5G/2.5G/1G/100M)
48 port Gbe Data Only
48 port Gbe Data with 30W PoE+
48 port Gbe Data with 60W UPOE
Description
Uplink Config
Modular U
Modular U
Modular U
Modular U
Modular U
Modular U
Modular U
1
Advertisement
Related Manuals for Cisco Meraki Catalyst 9300 Series
Summary of Contents for Cisco Meraki Catalyst 9300 Series
- Page 1 Catalyst 9300/X/L-M Series Installation Guide About this Guide This guide provides instruction on how to install and configure your Catalyst 9300/X/L-M series switches in the Meraki- managed mode. Product Overview Models Model number Description Uplink Config C9300-24T-M Modular U 24 port Gbe Data Only C9300-24P-M Modular U 24 port Gbe Data with 30W PoE+...
- Page 2 48 port Cisco UPOE, 36 ports 100M/1G/2.5G + 12 ports Multigigabit C9300-48UXM-M Modular U (10G/5G/2.5G/1G/100M) C9300-48UN-M 48 port 5Gbps Multigigabit UPOE ports (5G/2.5G/1G/100M) Modular U C9300-24S-M 24 port 1Gbe SFP Modular U C9300-48S-M 48 port 1Gbe SFP Modular U C9300X-12Y-M...
- Page 3 Note: For Japan, the recommendation is to deploy the switch with 200V+ outlets. The 1100/1900W power supplies will not operate on 100V. Please see the following chart for the appropriate 250VAC power cable. https://www.cisco.com/c/en/us/td/doc...e-powercords-1 Technical Specifications • Each model has 1 dedicated management interface (local status page access) •...
- Page 4 36 x 100M/1G/2.5G + 218.5 / 785.5 C9300-48UXM-M UPoE/802.3bt 490W Yes, Dual 12 x 100M/1G/2.5G/ 5G/10G 48 x 100M/1G/2.5G/ 157.9 / 843.8 C9300-48UN-M UPoE/802.3bt 645W Yes, Dual 84.6 / 124.3 C9300-24S-M 24 x 1GbE SFP Yes, Dual 88.9 / 158.3 C9300-48S-M 48 x 1 GbE SFP Yes, Dual...
- Page 5 Uplink 24 x 1GbE RJ45 C9300L-24P-4X-M PoE+/802.3bt 63.70 / 607 W 505W Yes, Dual 4 x 1G/10G SFP+ Uplink 48 x 1GbE RJ45 C9300L-48P-4X-M PoE+/802.3bt 67.40 / 598 W 505W Yes, Dual 4 x 1G/10G SFP+ Uplink 48 x 1GbE RJ45 67.38 / C9300L-48PF-4X-M PoE+/802.3bt...
- Page 6 Front Panel Components Inactive components: The following front panel components are used only when the device is being managed by DNAC of via CLI, and remain inactive in the Meraki-managed mode 1. STAT, Duplex, Speed, Stack, PoE, XPS and Console LEDs. 2.
- Page 7 LED Indicators in the Meraki-managed mode Blue Beacon System status System LED Switch is powered off or not receiving power. Switch if powered on and is loading the bootstrap firmware. Solid amber Switch is loading the operating system. Blinking green System error: Switch failed to load operating system or Blinking amber bootstrap firmware.
- Page 8 Back Panel Components Inactive components: When operating in the Meraki-managed mode, the C9300 will disable the RJ45 console port. Item Component Description Status Management Interface (Aux Connected, used for easy access to the local status Green Port) page Stack Ports Stack Cables are connected here Redundant Fans Green...
- Page 9 Catalyst 9300-M Deployment Best Practices Before powering on devices or connecting an uplink port to the LAN, ensure to follow the steps outlined below or watch this short video. The above video will link to a MS390 but the steps and information are the same for the C9300-M. Configure your Dashboard Network To add devices to your Meraki dashboard network please refer to the Creating a Dashboard Account and Organization...
- Page 10 Note: To utilize any VLANs outside of 1-1000 on a Catalyst Meraki C9300, the switch or switch stack must have ALL of its trunk interfaces set to an allowed vlan list that contains a total that is less than or equal to 1000 VLANs, including any of the module interfaces that are not in use.
- Page 11 Static IP via DHCP Reservations Instead of associating each Meraki switch individually to configure static IP addresses, an administrator can assign static IP addresses on the upstream DHCP server. Through “DHCP reservations,” IP addresses are “reserved” for the MAC addresses of the Meraki switches. Please consult the documentation for the DHCP server to configure DHCP reservations.
- Page 12 Installation Instructions 1. Attach the rack mount bracket to both sides of the switch as shown below: 2. Align the rack mount brackets on the sides of the switch onto the rack.
- Page 13 3. Secure and screw in the rack mount bracket on to the rack. 4. Insert the Uplink module. Note: The C9300/X uplink modules are hot-swappable and can be inserted/removed while powered.
- Page 14 (clockwise direction). Make sure the Cisco logo is on the top side of the connector. • Connect the other end of the cable to the port on the other switch and finger-tighten the screws. Avoid over tightening the screws.
- Page 15 If you are still experiencing hardware issues, please contact Cisco Meraki support by logging in to dashboard and using the Help option near the top of the page, then opening and email case or calling using the contact information on that page.
- Page 16 • The equipment is subject to installation and maintenance by specialists with the appropriate qualifications, sufficient specialized knowledge, and skills. • Rules and conditions for the sale of equipment are determined by the terms of contracts concluded by Cisco or authorized Cisco partners with equipment buyers.