Related Manuals for Racing RACD314T-2
Summary of Contents for Racing RACD314T-2
- Page 1 ORIGINAL INSTRUCTIONS >EN PETROL BRUSH CUTTER & GRASS TRIMMER RACD314T-2 USER GUIDE CAUTION: Read this manual before using this machine!
-
Page 2: Table Of Contents
CONTENTS 1. SAFETY INSTRUCTIONS........................3 2. YOUR PRODUCT..........................7 3. ASSEMBLY............................10 4. FILLING FUEL TANK AND OIL TANK................... 13 5. OPERATION............................15 6. MAINTENANCE AND STORAGE....................17 7. DECLARATION OF CONFORMITY....................19 8. WARRANTY............................20 9. PRODUCT FAILURE.......................... 21 10. WARRANTY EXCLUSIONS......................22... -
Page 3: Safety Instructions
1. SAFETY INSTRUCTIONS WARNING! When using this type of tool, basic precautions should always be followed to reduce the risk of fire and injury. Read all instructions carefully before attempting to use this product and retain these instructions. Be familiar with all the operations described in these operating instructions. This product must be operated by experienced users. - Page 4 Keep firm footing and balance during operation. Always use the harness provided. Have a correct working posture; stay stand, do not lean. The working positions should be changed regularly. Always inspect the machine before and after operation. If the tool is damaged or faulty, stop using the tool and bring it to an authorized service for inspection and repair.
- Page 5 When the machine is placed in storage for a long time, drain fuel from the fuel tank and carburetor, clean the parts, move the machine to a safe place and confirm that the engine is cooled down. Fuel Handling Be very careful when handling fuels. They are flammable and the vapors are explosive. Use only an approved container.
- Page 6 There are harmful health consequences resulting from the emission of vibrations if the product is used for long periods of time or not managed adequately and properly maintained. The vibrations can produce the so-called “white finger” disease. If any of the symptoms of "white finger"...
-
Page 7: Your Product
Caution! Risk of rebound. Keep bystanders away at least 15m. Caution! The tool can contact to a voluminous material. Loss of control and injuries can be created. Cutting attachment(Brush cutter) speed. Cutting attachment(Grass trimmer) speed. Guarantee sound power level Be careful of the cutting attachment! 2. - Page 8 5. Harness 6. Oil cup 7. 3 teethes blade 8. Wrench 9. Metal lock pin/ wrench 10. Nylon cutting head 11. Bar assembly 12. Bracket (handle part support) 13. Handle 14. Handle with throttle trigger, ON/OFF switch and throttle trigger lockout 15.
- Page 9 b. Technical data Engine displacement 31cm³ Maximum engine speed Brush cutter: 9300min-¹ Grass trimmer: 8000min-¹ Maximum power 0,7kW Mass Empty tank: 7,3kg Empty tank with specified attachment: 8kg Full tank and specified attachment: 8,5kg Volume of fuel tank 0,7l Volume of oil tank 0,08l Cutting diameter Grass trimmer: 480mm...
-
Page 10: Assembly
3. ASSEMBLY a) Installation of the tube on the tool Unscrew the bolt (1) and remove the screw cap (2). See Fig 1. Insert the attachment into the connector (Fig 2). Make sure to fix the pin into the hole of the tube. Put back the screw cap (2) and screw the bolt on it (3). - Page 11 c) Installation of the carter of protection Remove the screws which are on the carter of protection (fig7). Install the tube on the carter of protection. Make sure that you have installed it in the correct position (Fig 8). Screw the carter on the tube with the two screws (Fig 9). d) Installation of the nylon cutting head (for grass trimmer operation) Insert a metal locking tool into the hole on the side of the drive gear and on the tool drive (Fig 10).
- Page 12 e) Installation of metal blade (for brush cutter operation) Insert a metal locking tool into the hole on the side of the drive gear and on the tool drive (Fig 10). Remove cover bell and the holding nut from the shaft (Fig 11). Install, in the following order, on the shaft: the blade, the cover bell and then the holding nut (Fig 13).
-
Page 13: Filling Fuel Tank And Oil Tank
NOTE: After installation, always check if the installation is correct. If blade is not well install, it will vibrate excessively and can cause injury. When operation, if there is abnormal vibration, immediately stop the tool and check the installation. 4. FILLING FUEL TANK AND OIL TANK a) Fuel ... - Page 14 components (carburation, adjustment of spark plugs, control of exhaust opening and closing times) in the absence of accessories or a catalyst during combustion. Filling the tank Unscrew the tank cap. Fill the tank to 80% of its capacity. Screw the fuel cap back on. Clean the fuel tank cap and the area around after filling the fuel tank.
-
Page 15: Operation
5. OPERATION a) Starting the tool Move the ON/OFF switch to “ON” position (I). Pull the recoil starter until engine starts. For the operation, push and hold the throttle trigger lockout (1) and then push the throttle trigger (2). b) Stopping the tool Release the throttle trigger and the throttle trigger lockout. - Page 16 Tilt the head slowly to direct debris away from you. If cutting up to a barrier such as fence, wall or tree, approach from an angle where any debris ricocheting off the barrier will fly away from you, Move the line head slowly until the grass is cut right up the barrier, but do not jam (overfeed) the line into the barrier.
-
Page 17: Maintenance And Storage
Scything weeds This is cutting by swinging the blade in a level arc. It can quickly clear areas of field grass and weeds. Scything should not be used to cut large, tough weeds or woody growths. Scything can be done in both directions, or just in one way which results in the debris being thrown away from you. - Page 18 f) Blade Always clean and grind the blade, check whether the blade is firmly installed before use, and check whether the blade is damaged if it encounters obstacles. If it is not used for a long time, clean the blade surface and apply lubricant to avoid rust. g) Grass trimmer Replacement of the cutting string Push the tab which is on the housing cutting string and turn the cover to open it (see the...
-
Page 19: Declaration Of Conformity
32 rue Aristide Bergès - Z.I. du Casque - 31270 Cugnaux - France Tel : +33 (0)5.34.502.502 Fax : +33 (0)5.34.502.503 declares that the machine: PETROL BRUSH CUTTER & GRASS TRIMMER RACD314T-2 Serial No: 20230400001-20230402100 have been designed in compliance with the following standards: EN ISO 11806-1:2022... -
Page 20: Warranty
8. WARRANTY WARRANTY The manufacturer guarantees the product against defects in material and workmanship for a period of 2 years from the date of the original purchase. The warranty only applies if the product is for household use. The warranty does not cover breakdowns due to normal wear and tear. The manufacturer agrees to replace parts identified as defective by the designated distributor. -
Page 21: Product Failure
9. PRODUCT FAILURE WHAT TO DO IF MY MACHINE BREAKS DOWN? If you bought your product in a store: a) Empty the fuel tank if your product has one. b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case, the repairer will refuse the machine. -
Page 22: Warranty Exclusions
10. WARRANTY EXCLUSIONS THE WARRANTY DOES NOT COVER: • Start-up and setting up of the product. • Damage resulting from normal wear and tear of the product. • Damage resulting from improper use of the product. • Damage resulting from assembly or start-up not in accordance with the user manual. •... - Page 23 BUILDER SAS 32 rue Aristide Bergès - Z.I. du Casque - 31270 Cugnaux - France MADE IN PRC 2023...