Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Asus ROG Flow Z13 Series
Summary of Contents for Asus ROG Flow Z13 Series
- Page 1 ASUS ROG Flow Z13 (GZ301Z) Series Service Guide...
- Page 2 LIMITATION OF LIABILITY Circumstances may arise where because of a default on ASUS’ part or other liability, you are entitled to recover damages from ASUS. In each such instance, regardless of the basis on which you are entitled to claim damages from ASUS, ASUS is liable for no more than damages for bodily injury (including death) and damage to real property and tangible personal property;...
- Page 3 Disclaimer ASUS is not responsible for direct, indirect, intentional or unintentional damages resulting from improper installation and operation. Safety precautions • Keep liquids or moisture away from your Notebook PC before installing or removing any components. • Ensure to place your Notebook PC on a stable surface before installing or removing any components.
-
Page 4: Table Of Contents
Table of Contents ⚫ Service Overview ⚫ ASUS ROG Flow Z13 (GZ301Z) Series Overview ⚫ Components Top View ⚫ Components Bottom View ⚫ Repair Overview ⚫ Appropriate Tools ⚫ Keyparts and Related Parts ⚫ Disassembly Steps : • KEYBOARD •... -
Page 5: Service Overview
Service Overview • Carefully read through this Service Guide for a look at various components of the device before performing any service and repairs. • To provide the best service, we have provided the below information for technicians from distributors and resellers to perform the complete device disassembly and assembly. -
Page 6: Asus Rog Flow Z13 (Gz301Z) Series Overview
ASUS ROG Flow Z13 (GZ301Z) Series Overview Front View Rear View ❶ Array microphones ❺ Microphone ❷ Camera ❻ Air vents ❸ Camera indicator ❼ Kickstand ❹ Touch screen panel ❽ MicroSD card slot ❶ Power Button TOP View RIGHT View ❷... -
Page 7: Components Top View
Components Top View BATTERY A COVER ASSY FRONT CAM FPC CAM CONNECTOR_BD CAMERA MODULE 8M HINGE VOL FPC LCD MODULE BATTERY SPONGE USB BD Antenna POGO FPC LCD EDP MAIN Vol key Sponge THERMAL MODULE LED_FPC TOUCH PANEL FFC THERMAL MODULE MAIN BOARD VOL KEY SPEAKER... - Page 8 Components Top View MB SSD GASKET FRONT CAMERA RUBBER MB GC CONN GASKET BEZEL SPONGE L BEZEL SPONGE R LCD TOUCH IC GASKET INDICATOR LENS FP POWER BUTTON LED FPC Gasket LED FPC GASKET HINGE SAFETY SPONGE GLASS CONDUCTIVE TAPE Back...
-
Page 9: Components Bottom View
Components Bottom View A COVER ASSY LCD EDP CAMERA MODULE 8M LCD CONN SPONGE LCD MODULE KICKSTAND ASSY THERMAL MODULE THERMAL MODULE MAIN BOARD CAM CONNECTOR_BD (For GZ301ZA SKU Only) SSD DOOR USB BD (SSD DOOR ABSORBER) Back... -
Page 10: Repair Overview
Repair Overview This chapter describes disassembly and assembly (Assemble document please look up from the last page), please follow the information provided in this section to perform the complete disassembly procedure. Precautions: Before you perform any service or repair on the notebook, please pay special attention to the cautions prevent any damages to the notebook. 1. -
Page 11: Appropriate Tools
Appropriate Tools Please prepare and select the appropriate tools to disassemble/assemble for the ASUS ROG Flow Z13 (GZ301Z) Series notebook. Screwdriver Alcohol 95% Glove Dust-free Cloth Please accord to different screw specification to choose different screwdriver and head. Plastic Blade PLASTIC CARD T=0.35mm... - Page 12 Appropriate Tools Please prepare and select the appropriate tools to disassemble/assemble for the ASUS ROG Flow Z13 (GZ301Z) Series notebook. ❶ ❼ ❷ ❸ ❺ ❹ ❻ Item Part Name Memo ❶ Silicone scraping pen Please store it in the environment of 10 ~ 40 ℃.
-
Page 13: Keyboard
KEYBOARD Disassembly Notice Please be sure to pull out adapter. Step 1 : Remove the Keyboard from device. Back... -
Page 14: Ssd
Disassembly Notice Please be sure to pull out adapter. Screws Spec Torque (kgf-cm) M2*4.8L (3.1,0.8) (K)+H #1 1.8±0.2 Step 1 : Turn on the KICKSTAND. Step 2 : Remove screw *1pc, and SSD DOOR. M2*2.5L (5,0.5) (K) #1 1.8±0.2 Step 3 : Remove screw *1pc, and SSD. Assembly Notice Open Step 1. -
Page 15: Lcd Module
LCD MODULE Disassembly Notice Please be sure to pull out adapter. Screws Spec Torque (kgf-cm) Step 1 : Turn on the KICKSTAND, and remove screws *4pcs. Step 2 : Using LCD Screen Opening to position on middle upper of panel. M1.6*8L (3.1,0.8) (K)+H T5 1.8±0.2 Step 3 : Clamp LCD Screen Opening to separate the panel from the frame, and creating a gap. - Page 16 LCD MODULE Assembly Notice Please be sure to pull out adapter and disconnect the battery. Sample pasted For BEZEL SPONGE R and BEZEL SPONGE L assembly, please For BEZEL ACETATE 1 assembly, please follow the location and alignment to paste the sponge. confirm the Green mark and follow the Red line to paste and clad on each snap.
-
Page 17: Battery
BATTERY Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Before disassembly battery connector, please be sure to pull out adapter and disconnect the battery more than ten seconds in order to IC damage. Step 1 : Check and disconnect the battery connector. Step 2 : Remove screws *6pcs. -
Page 18: Speaker
SPEAKER Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Disconnect SPEAKER connector. Screws Spec Torque (kgf-cm) Assembly Notice Step 2 : Release SPK ACERATE. M2*3L D3.5 (K) B-NI,NY 2.0±0.2 Step 3 : Remove screws *4pcs. When Speaker assembly, please follow the mark below Step 4 : Remove SPEAKER. - Page 19 CAMERA CONNECT BOARD & CAMERA MODULE 8M Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Disconnect FPC cable. Screws Spec Torque (kgf-cm) Step 2 : Remove screws *4pcs, and CAM Connect BD. Step 3 : Disconnect the Rear CAM Module 8M, then remove it.
-
Page 20: Camera Connect Board& Rear Camera Module 8M
CAMERA CONNECT BOARD & REAR CAMERA MODULE 8M Assembly Notice Please be sure to pull out adapter and disconnect the battery. When Camera Connect Board & Camera Module 8M assembly, When Rear Camera FPC & Rear Camera Module 8M assembly, If FFC is damage during disassembly, please follow the step below to assemble. -
Page 21: Fan
Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Disconnect Fan connector *2pcs. Screws Spec Torque (kgf-cm) Assembly Notice Step 2 : Remove screws *4pcs. M2*5L (K)B-ZN,NY 1.8±0.2 Step 3 : Tear off Mylar *2pcs. After the FAN assembled, please follow the mark below Step 4 : Remove Fan *2pcs. -
Page 22: Usb Board
USB BOARD Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Tear off HINGE MYLAR *2pcs. Screws Spec Torque (kgf-cm) Step 2 : Remove screws *11pcs, and then remove HINGE MASK MYLAR *2pcs and HINGE *2pcs. M2*3L D3.5 (K) B-NI,NY 2.0±0.2 Step 3 : Disconnect FPC cable *2pcs and remove screw *1pc. - Page 23 USB BOARD Assembly Notice Please be sure to pull out adapter and disconnect the battery. When HINGE assembly, please follow the location below to When HINGE MASK MYLAR assembly, please paste HINGE SAFETY MYLAR. follow direction below to position the Mylar. (The Mylar notch are both to the right) (HINGE L) (HINGE R)
-
Page 24: Thermal Module& Camera Hd Fix 3.3V Cr
THERMAL MODULE & CAMERA HD FIX 3.3V CR Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Screws Spec Torque (kgf-cm) Retention Screw 1.8±0.2 Step 1 : Please follow the reverse screw numbers to release screws *8pcs. Step 2 : Remove the THERMAL MODULE from MB. - Page 25 THERMAL MODULE & CAMERA HD FIX 3.3V CR Assembly Notice Please be sure to pull out adapter and disconnect the battery. Step-1 When thermal module assembly, please align it according to THERMAL MODULE Location:[VRAM/CHOKE/MOS] the positioning column below, and then put down vertically to Material: FCR-AS Grease assemble the thermal...
-
Page 26: Main Board
MAIN BOARD Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Release MB SSD Gasket *1pc, and LED FPC Gasket *2pcs. Screws Spec Torque (kgf-cm) Step 2 : Disconnect cable *3pcs, and remove screws * 9pcs M2*2L (6.6,0.55) (K) #1 1.8±0.2 Step 3 : Remove the Main Board. - Page 27 MAIN BOARD Assembly Notice Please be sure to pull out adapter and disconnect the battery. When Main Board assembly, please follow the mark below When Main Board assembly, please follow After POGO FPC and USB BOARD FPC assembled, please follow to fix MB GC CONN GASKET、MB SSD Gasket and LED FPC the mark below to fix HINGE SAFETY the location below to fix EC BRK KAPTON.
- Page 28 MAIN BOARD Mainboard connector placement FRONT CAM FPC REAR CAM FPC SPEAKER BATTERY CABLE USB BOARD FPC POGO FPC EDP CABLE TOUCH PANEL FFC Supports using JIG BOARD to refresh F1 BIOS Back...
- Page 29 MAIN BOARD Materials on mainboard NR2201ZE GPU BRACKET ASSY NR2201ZE MB BOT CPU ABSORBER NR2201ZE MB MIC MESH NR2201ZE MB TOP ABSORBER (For GZ301ZE/ZC) NR2201ZE MB BOT GPU ABSORBER NR2201ZE MB BOT RAM ABSORBER NR2201ZE MB BOT ACERATE NR2201ZE MB BOT LED SPONGE NR2201ZE EC BRK KAPTON NR2201ZE CPU BRACKET ASSY (For GZ301ZE/ZC)
- Page 30 MAIN BOARD Materials on mainboard NR2201ZE MB EMI GASKET NR2201ZE MB BOSS WASHER 1 (For GZ301ZE/ZC) NR2201ZE MB TOP GPU ABSORBER GROUNDSMD GASKET W5*H5.5*L6 (For GZ301ZE/ZC) NR2201ZE MB TOP GPU ABSORBER A NR2201ZE MB TYPE C GASKET (For GZ301ZE/ZC) NR2201ZE MBTOP KAPTON NR2201ZE MB TOP DDR ABSORBER A (For GZ301ZE/ZC) NR2201ZE MB TOP DDR ABSORBER...
-
Page 31: Wifi Antenna (With Side Key)
WIFI ANTENNA (with SIDE KEY) Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Remove screws *2pcs. Screws Spec Torque (kgf-cm) Step 2 : Remove WIFI Main and Aux Antenna. M1.6*4L (3.2,0.6) (K) #0 1.4±0.1 Step 3 : Remove screws *3pcs. - Page 32 WIFI ANTENNA (with SIDE KEY) Assembly Notice Please be sure to pull out adapter and disconnect the battery. When VOL KEY assembly, please follow the direction When WIFI Main and Aux Antenna& CAMERA HD FIX 3.3V CR (Green circle up) to assemble. assembly, please follow below location to tidy cables.
-
Page 33: A Cover
A COVER Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Remove INDICATOR LENS. Step 2 : Remove FP POWER BUTTON. Step 3 : Release LED FPC Gasket and remove LED FPC. Step 4 : Remove KICKSTAND ASSY from Cover. Push the MYLAR SPONGE Remove (FP POWER BUTTON) Remove(Yellow mark) - Page 34 A COVER Assembly Notice Please be sure to pull out adapter and disconnect the battery. Once inside of deco glass is with dust and dirt, please clean it When LED FPC & LED FPC Gasket assembly, please follow with alcohol and Dust-free Cloth. below location to fix.