Advertisement
2. TECHNICAL SPECIFICATION
Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V, 130W
Speed Range. . . . . . . . . . . . . . . . . . . . . 8000 to 30000 rpm
Speed Settings. . . . . . . . . . . . . . . . . . . . . . Stepless Control
Collet Sizes. . . . . . . . . . . . . . . . .1.5mm, 2.3mm, 3.3mm (x2)
For kit contents, refer to the Parts List.
3. OPERATING INSTRUCTIONS
3.1
Connection
3.1.1
Ensure that the ON/OFF switch is in the OFF position
before connecting to the mains supply. Refer to fig.1,
'OFF' is shown as '0' on the switch.
3.2
Fitting Accessories Direct to Rotary Tool
3.2.1
Ensure that the tool is switched OFF.
3.2.2
Press the spindle lock button, refer to fig.1, and
slowly turn the collet nut until the spindle lock
engages.
3.2.3
Retain the pressure on the spindle lock button and
anticlockwise to open the collet (fig.3)
NOTE: Never press the spindle lock button when the tool is running.
3.2.4
The required bit may now be fitted into the collet. Fully insert the bit shaft to reduce the risk of bending in use. Tighten the collet nut
firmly. Finally, release the spindle lock button.
3.2.5
To change collets, proceed as 3.2.1 to 3.2.3 but continue to unscrew the collet nut until it can be removed from the spindle. Change
collets and replace the collet nut.
3.2.6
Select the speed required on the variable speed control. Small accessories require high
speed and large accessories low speed. If in doubt, start on a low setting and gradually
increase speed until best performance is obtained.
3.2.7
Check that the ON/OFF switch is at OFF and then connect the tool to the mains power
supply. Turn the ON/OFF switch to ON.
DO NOT switch ON with the tool bit touching the workpiece. Always allow the bit
to reach full speed before applying it to the workpiece.
3.3
Attaching Flex Drive and Bits.
Ensure that the tool is switched OFF and remove plastic collar (fig.1)
3.3.1
Press the spindle lock button, refer to fig.1 or fig.2A, and slowly turn the collet nut until the spindle lock engages.
3.3.2
Retain the pressure on the spindle lock button and turn the collet nut anticlockwise to loosen the collet.
3.3.3
Extract the flex drive from the centre of the shaft (fig.2B).
3.3.4
Insert the flex drive into the collect inside the spindle and tighten by holding in the spindle locking button and tighten with the
wrench (fig.2).
3.3.5
Slide the flex drive back up into the shaft and secure by screwing the rotary shaft connector onto the rotary tool (fig.2).
3.3.6
At the other end of the flex drive shaft pull back the outer casing and turn the collet nut anticlockwise to loosen.
3.3.7
Replace the collet with one the correct size for the task at hand.
3.3.8
Replace the collet nut and insert a bit. Tighten the collet nut firmly.
4.
MAINTENANCE
4.1.
Cleaning
4.1.1
Keep the tool ventilation slots clean and free from obstructions. If available blow compressed air into the vents to clear any
internal dust (safety goggles must be worn when undertaking this process).
4.1.2
Keep the outer case of the tool clean and free from grease.
4.1.3
Wipe down with a damp cloth.
DO NOT wash with water or use solvents or abrasives.
4.2.
Servicing
To service the tool contact your local Sealey service agent.
5.
DECLARATION OF CONFORMITY
Declaration of Conformity
Multipurpose Rotary Tool
Model E5188
2006/95/EC Low Voltage Directive
2004/108/EC EMC Directive
93/68/EEC CE Marking
2006/42/EC Machinery Directive
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including
We, the sole importer into the UK, declare that the product listed here is in conformity with the following standards and directives.
The construction files for this product is held by the Manufacturer and may be inspected, by a
national authority, upon request to Jack Sealey Ltd.
For Jack Sealey Ltd. Sole importer into the UK of Sealey Power Tools.
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
turn the collet nut
Signed by Tim Thompson
01284 757500
01284 703534
fig.1
fig.2
fig.3
Date 8th October 2006
postcode.
www.sealey.co.uk
Web
sales@sealey.co.uk
email
E5188 - 2 - 081007
Advertisement
