Related Manuals for Dell dxcwrk1 - XPS - One
Summary of Contents for Dell dxcwrk1 - XPS - One
- Page 1 Dell XPS One 2710 Owner’s Manual Computer model: XPS One 2710 Regulatory model: W06C | Regulatory type: W06C001...
- Page 2 Microsoft Corporation in the United States and/or other countries; ® Bluetooth is a registered trademark owned by Bluetooth SIG, Inc. and is used by Dell under ® ™ license. Intel is a registered trademark and Intel SpeedStep is a trademark of Intel Corporation in the U.S.
-
Page 3: Table Of Contents
Contents Before You Begin ..... . . Turn Off Your Computer and Connected Devices Recommended Tools ..... Safety Instructions . - Page 4 10 Removing the System-Board Shield ..Prerequisites ......Procedure .
- Page 5 20 Removing the Hard Drive ....Prerequisites ......Procedure .
- Page 6 30 Removing the mSATA Mini-Card ..Prerequisites ......Procedure .
- Page 7 40 Removing the I/O Panel ....Prerequisites ......Procedure .
- Page 8 50 Removing the System Board ... . . Prerequisites ......Procedure .
- Page 9 60 Removing the Display Panel ... . . Prerequisites ......Procedure .
- Page 10 70 System Setup ......Overview ......Entering System Setup .
-
Page 11: Before You Begin
Before You Begin Turn Off Your Computer and Connected Devices CAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your computer. Save and close all open files and exit all open programs. Click Start and click Shut Down. -
Page 12: Safety Instructions
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. WARNING: Disconnect all power sources before opening the computer cover or panels. -
Page 13: After Working Inside Your Computer
After Working Inside Your Computer After you complete the replacement procedures, ensure the following: • Replace all screws and ensure that no stray screws remain inside your computer • Connect any external devices, cables, cards, and any other part(s) you removed before working on your computer •... - Page 14 After Working Inside Your Computer...
-
Page 15: Technical Overview
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Inside View of Your Computer... -
Page 16: System-Board Components
System-Board Components display-power cable connector camera-cable connector Infrared-module cable connector memory-module connector (DIMM 1) memory-module connector (DIMM 2) wireless mini-card connector mSATA mini-card connector CMOS jumper speaker-cable connector coin-cell battery socket power-button cable connector converter-board cable connector volume/display-settings controls I/O-board connector cable connector Technical Overview... - Page 17 password jumper TV-tuner mini-card connector hard-drive data-cable connector optical-drive data-cable connector optical-drive power-cable connector hard-drive power-cable connector main (8-pin) power-cable connector LVDS-cable connector processor socket touchscreen-cable connector processor (4-pin) power-cable connector processor heat-sink fan-cable connector Technical Overview...
- Page 18 Technical Overview...
-
Page 19: Removing The Back Cover
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure Place the computer face-down on a clean and flat surface. - Page 20 Removing the Back Cover...
-
Page 21: Replacing The Back Cover
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure Place the back cover over the inner frame and slide the back cover toward the bottom of the computer. - Page 22 Replacing the Back Cover...
-
Page 23: Removing The Converter Board
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the back cover. - Page 24 Removing the Converter Board...
-
Page 25: Replacing The Converter Board
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure Align the screw holes on the converter board with the screw holes on the computer base. - Page 26 Replacing the Converter Board...
-
Page 27: Removing The Optical Drive
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the back cover. - Page 28 Remove the screws that secure the optical-drive brackets to the optical drive. Remove the optical-drive brackets from the optical drive. screws (4) optical-drive brackets (2) optical drive Removing the Optical Drive...
-
Page 29: Replacing The Optical Drive
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure... - Page 30 Replacing the Optical Drive...
-
Page 31: Removing The System-Board Shield
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the back cover. - Page 32 Removing the System-Board Shield...
-
Page 33: Replacing The System-Board Shield
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure Align the screw holes on the system-board shield with the screw holes on the computer base. - Page 34 Replacing the System-Board Shield...
-
Page 35: Removing The Power-Supply Unit
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the back cover. - Page 36 Lift the power-supply unit off the computer base. power-supply unit screws (4) processor power-supply cable connector 4 main power-supply cable connector power-port cable power-supply indicator cable connector power-supply fan cable connector Removing the Power-Supply Unit...
-
Page 37: Replacing The Power-Supply Unit
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure... - Page 38 Replacing the Power-Supply Unit...
-
Page 39: Removing The Memory Module(S)
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the Back Cover. - Page 40 Use your fingertips to carefully spread apart the securing clips on each end of the memory-module connector until the memory module pops up. Remove the memory module from the memory-module connector. securing-clips (2) memory module memory-module connector Removing the Memory Module(s)
-
Page 41: Replacing The Memory Module(S)
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure Align the notch on the memory module with the tab on the memory-module connector. - Page 42 Replacing the Memory Module(s)
-
Page 43: Removing The Coin-Cell Battery
11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. WARNING: The battery may explode if installed incorrectly. Replace the battery only with the same or equivalent type. - Page 44 Removing the Coin-Cell Battery...
-
Page 45: Replacing The Coin-Cell Battery
11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. WARNING: The battery may explode if installed incorrectly. Replace the battery only with the same or equivalent type. - Page 46 Replacing the Coin-Cell Battery...
-
Page 47: Removing The Stand
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the Back Cover. - Page 48 Removing the Stand...
-
Page 49: Replacing The Stand
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure Insert the tab at the top of the stand into the slot on the computer base. - Page 50 Replacing the Stand...
-
Page 51: Removing The Hard Drive
11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. CAUTION: To avoid data loss, do not remove the hard drive while the computer is in Sleep or On state. - Page 52 Remove the screws that secure the straps to the hard drive and remove the straps from the hard drive. screws (4) hard drive straps (2) Removing the Hard Drive...
-
Page 53: Replacing The Hard Drive
11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. CAUTION: Hard drives are extremely fragile. Exercise care when handling the hard drive. - Page 54 Replacing the Hard Drive...
-
Page 55: Removing The Hard-Drive Cage
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the back cover. - Page 56 Removing the Hard-Drive Cage...
-
Page 57: Replacing The Hard-Drive Cage
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure Align the screw holes on the hard-drive cage with the screw holes on the computer base. - Page 58 Replacing the Hard-Drive Cage...
-
Page 59: Removing The Power-Supply Fan
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the back cover. - Page 60 Removing the Power-Supply Fan...
-
Page 61: Replacing The Power-Supply Fan
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure Route the power-supply fan cable under the I/O-board assembly and then connect the power-supply fan cable to the power-supply unit. - Page 62 Replacing the Power-Supply Fan...
-
Page 63: Removing The Tv-Tuner Mini-Card
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the back cover. - Page 64 Removing the TV-Tuner Mini-Card...
-
Page 65: Replacing The Tv-Tuner Mini-Card
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure Align the notch on the TV-tuner mini-card with the tab on the TV-tuner mini-card connector. - Page 66 Replacing the TV-Tuner Mini-Card...
-
Page 67: Removing The Wireless Mini-Card
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the back cover. - Page 68 Slide and remove the wireless mini-card out of the wireless mini-card connector. wireless mini-card connector wireless mini-card Removing the Wireless Mini-Card...
-
Page 69: Replacing The Wireless Mini-Card
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure CAUTION: To avoid damage to the mini-card, ensure that no cables are placed under the wireless mini-card. - Page 70 Replacing the Wireless Mini-Card...
-
Page 71: Removing The Msata Mini-Card
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the back cover. - Page 72 Removing the mSATA Mini-Card...
-
Page 73: Replacing The Msata Mini-Card
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure Align the notch on the mSATA mini-card with the tab on the mSATA mini-card connector. - Page 74 Replacing the mSATA Mini-Card...
-
Page 75: Removing The Processor Heat-Sink Fan
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the back cover. - Page 76 Removing the Processor Heat-Sink Fan...
-
Page 77: Replacing The Processor Heat-Sink Fan
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure... - Page 78 Replacing the Processor Heat-Sink Fan...
-
Page 79: Removing The Processor Heat-Sink
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the back cover. - Page 80 Removing the Processor Heat-Sink...
-
Page 81: Replacing The Processor Heat-Sink
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure NOTE: The original thermal grease can be reused if the original system board and heat sink are reinstalled together. - Page 82 Replacing the Processor Heat-Sink...
-
Page 83: Removing The Processor
11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. CAUTION: Processors are extremely fragile. Handle the processor only by the edges and do not touch the metal pins. - Page 84 Removing the Processor...
-
Page 85: Replacing The Processor
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure Ensure that the release lever on the processor socket is fully extended in the open position. -
Page 86: Postrequisites
Postrequisites Replace the processor heat-sink. See "Replacing the Processor Heat-Sink" on page 81. Replace the system-board shield. See "Replacing the System-Board Shield" on page 33. Replace the back cover. See "Replacing the Back Cover" on page 21. Replacing the Processor... -
Page 87: Removing The Trim Cover
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the back cover. - Page 88 Removing the Trim Cover...
-
Page 89: Replacing The Trim Cover
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure Insert the tabs at the bottom of the trim cover into the slots on the inner frame. - Page 90 Replacing the Trim Cover...
-
Page 91: Removing The I/O Panel
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the back cover. - Page 92 Removing the I/O Panel...
-
Page 93: Replacing The I/O Panel
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure Align the slots on the I/O panel with the ports on the I/O assembly. - Page 94 Replacing the I/O Panel...
-
Page 95: Removing The Inner Frame
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the back cover. - Page 96 Removing the Inner Frame...
-
Page 97: Replacing The Inner Frame
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure Align the screw holes on the inner frame with the screw holes on the computer base. - Page 98 Replacing the Inner Frame...
-
Page 99: Removing The I/O-Board
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the back cover. - Page 100 Remove the TV-in port cable and the infrared-emitter port cable from their routing guides. Lift the I/O-board assembly off the computer base. power-supply light cable power-port cable TV-in port cable infrared-emitter port cable I/O-board assembly Push the securing tabs outward to release the I/O board and then lift the I/O board away from the I/O-board bracket.
-
Page 101: Replacing The I/O Board
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure Slide the power-port cable and power-supply light cable through the slot on the I/O-board bracket. - Page 102 Replacing the I/O Board...
-
Page 103: Removing The Tv-In Port
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the back cover. - Page 104 Removing the TV-In Port...
-
Page 105: Replacing The Tv-In Port
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure Slide the TV-in port cable through the slot on the I/O-board bracket. - Page 106 Replacing the TV-In Port...
-
Page 107: Removing The Infrared-Emitter Port
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the back cover. -
Page 108: Procedure
Procedure Remove the nut that secures the infrared-emitter port to the I/O-board bracket. Remove the infrared-emitter port and the infrared-emitter port cable from the I/O-board assembly. Infrared-emitter port infrared-emitter port cable Removing the Infrared-Emitter Port... -
Page 109: Replacing The Infrared-Emitter Port
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure Slide the infrared-emitter port through the slot on the I/O-board bracket. - Page 110 Replacing the Infrared-Emitter Port...
-
Page 111: Removing The System Board
11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. NOTE: Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in system setup after you replace the system board. -
Page 112: Procedure
Procedure Disconnect the following cables from the system board: • Speaker cable • Power-button cable • Converter cable • Volume/Display-settings control cable • Hard-drive data cable • Hard-drive power cable • Optical-drive data cable • Optical-drive power cable • Main and processor power-supply cables •... -
Page 113: Replacing The System Board
11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. NOTE: Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the system setup after you replace the system board. -
Page 114: Postrequisites
Postrequisites Replace the processor. See "Replacing the Processor" on page 85. Replace the processor heat-sink. See "Replacing the Processor Heat-Sink" on page 81. Replace the wireless mini-card. See "Replacing the Wireless Mini-Card" on page 69. Replace the mSATA mini-card. See "Replacing the mSATA Mini-Card" on page 73. Replace the TV-tuner mini-card. -
Page 115: Removing The Speakers
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the back cover. - Page 116 Removing the Speakers...
-
Page 117: Replacing The Speakers
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure Align the screws holes on the speakers with the screw holes on the computer base. - Page 118 Replacing the Speakers...
-
Page 119: Removing The Power-Button Assembly
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the back cover. - Page 120 Removing the Power-Button Assembly...
-
Page 121: Replacing The Power-Button Assembly
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure Place the power-button assembly in the computer base and ensure that the power button fits in the slot on the computer base. - Page 122 Replacing the Power-Button Assembly...
-
Page 123: Removing The Side I/O-Board
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the back cover. -
Page 124: Procedure
Procedure Remove the screws that secure the side I/O-board shield to the computer base. Remove the side I/O-board shield. grounding cable side I/O-board screws (2) side-I/O-board shield Gently lift the side I/O-board starting from the inner edge and then ease the ports on the side I/O-board out of the slots on the computer base. -
Page 125: Replacing The Side-I/O Board
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure... - Page 126 Replacing the Side-I/O Board...
-
Page 127: Removing The Middle Cover
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the back cover. -
Page 128: Procedure
Procedure Disconnect the display-backlight cable from the display assembly. Remove the screw that secures the grounding cable to the computer base. Remove the plastic shield above the LVDS and display-power cables. Press the securing clips and disconnect the LVDS cable from the display assembly. Disconnect the touchscreen cable from the display assembly. - Page 129 Remove the following cables from the routing guides on the middle frame: • LVDS cable • Display-power cable • Infrared-receiver cable • Camera cable • Hard-drive power and data cable • Optical-drive power and data cable • Converter cable • Power-button cable •...
- Page 130 Removing the Middle Cover...
-
Page 131: Replacing The Middle Cover
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure Place the middle cover on the computer base and route the cables through their slots on the middle cover. -
Page 132: Postrequisites
Postrequisites Replace the side I/O-board. See "Replacing the Side-I/O Board" on page 125. Follow step 1 to step 3 in "Replacing the System Board" on page 113. Replace the converter board. See "Replacing the Converter Board" on page 25. Replace the power-supply unit. See "Replacing the Power-Supply Unit" on page 37. Replace the power-supply fan. -
Page 133: Removing The Display Panel
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the back cover. - Page 134 Remove the plastic shield and remove the display-power, LVDS, and touchscreen cables from their routing guides. LVDS cable display-power cable touchscreen cable camera cable infrared-module cable wireless mini-card wireless-antenna cables (2) volume/display-settings controls cable Disconnect the display-backlight cable from the display assembly. Remove the screw that secures the grounding cable to the processor cooling vents.
- Page 135 Remove the screws that secure the side I/O-board shield to the computer base and remove the side I/O-board shield. processor cooling-vents grounding cable grounding-cable screw side I/O-board shield screws (2) system-board screws (2) side I/O-board shield system board grounding-cable screw speaker grounding cable display-backlight cable Removing the Display Panel...
- Page 136 WARNING: The middle cover is heavy when the components are attached to it. It is recommended that two people remove and replace the middle cover while the components are attached to it. Using the hard-drive cage, gently lift the middle-cover assembly along with the components and ease the cables out of the slots.
- Page 137 Push the tabs and disconnect the ribbon cables from the display assembly. Peel off the tapes securing the ribbon cables to the display assembly. tabs ribbon cables (6) tape Remove the screws that secure the display assembly to the computer base. Lift the display assembly from the computer base.
- Page 138 Remove the screws that secure the display brackets to the display panel. Remove the display brackets from the display panel. display panel display brackets (2) screws (4) Removing the Display Panel...
-
Page 139: Replacing The Display Panel
11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. WARNING: The middle cover is heavy when the components are attached to it. It is recommended that two people remove and replace the middle cover while the components are attached to it. -
Page 140: Postrequisites
Route the display-power, LVDS, and touchscreen cables through their routing guides and replace the plastic shield. Route the camera and infrared-module cables through their routing guides and connect the cables to the system board. Route the wireless-antenna cables through their routing guides and connect the antenna cables to the wireless mini-card. -
Page 141: Removing The Camera Module
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the back cover. -
Page 142: Procedure
Procedure Remove the screws that secure the camera assembly to the computer base. Gently lift the camera assembly and disconnect the camera cable from the camera assembly. screws (2) camera assembly camera cable Loosen the captive screw that secures the camera module and the grounding cable to the camera assembly. -
Page 143: Replacing The Camera Module
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure Slide the camera module into the camera assembly. - Page 144 Replacing the Camera Module...
-
Page 145: Removing The Microphone Modules
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the back cover. -
Page 146: Procedure
Procedure Disconnect the microphone cables from the microphone modules. Using a plastic scribe, pull the securing tabs and slide the microphone module upward. microphone cable microphone modules (2) securing tab Remove the microphone module out of the microphone-module socket. Removing the Microphone Modules... -
Page 147: Replacing The Microphone Modules
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure Align the microphone modules with the microphone-module socket and insert the microphone modules into the microphone-module socket. - Page 148 Replacing the Microphone Modules...
-
Page 149: Removing The Infrared (Ir) Module
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the back cover. -
Page 150: Procedure
Procedure Lift the securing tab and slide the IR receiver out of the IR-receiver socket. Ease the IR-activity light out of the IR-activity light socket. Remove the IR module from the computer base. IR receiver IR-receiver cable IR-activity light IR-activity light cable Removing the Infrared (IR) Module... -
Page 151: Replacing The Infrared (Ir) Module
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure With the sensor side facing toward the front of the computer, slide the IR receiver into the IR-receiver socket till the IR receiver locks in place. - Page 152 Replacing the Infrared (IR) Module...
-
Page 153: Removing The Antenna Module(S)
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Prerequisites Remove the back cover. -
Page 154: Procedure
Procedure Disconnect the wireless-antenna cables from the wireless mini-card. Note the routing of the antenna cables and remove the cables from the routing guides. Peel the antennas modules off the computer base. Lift the antenna modules out of the computer base. antenna modules (2) wireless mini-card wireless-antenna cables (2) -
Page 155: Replacing The Antenna Module(S)
"Before You Begin" on page 11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Procedure Align the antenna modules with the alignment posts on the computer base and adhere the antenna modules to the computer base. - Page 156 Replacing the Antenna Module(s)
-
Page 157: System Setup
Entering System Setup Turn on (or restart) your computer. During POST, when the DELL logo is displayed, watch for the F2 prompt to appear and then press <F2> immediately. NOTE: The F2 prompt indicates that the keyboard has initialized. This prompt can appear very quickly, so you must watch for it, and then press <F2>. -
Page 158: System Setup Screens
System Setup Screens The system setup screen displays current or changeable configuration information for your computer. Information on the screen is divided into three areas: the setup item, active help screen, and key functions. Setup Item — This field appears on the left Help Screen —... - Page 159 Main → Processor Information Displays the processor type. Processor Type Displays the processor identification code. Processor ID Displays the number of processor cores in your Processor Core Count computer. Displays the processor’s total L1 cache size. Processor L1 Cache Displays the processor’s total L2 cache size. Processor L2 Cache Displays the processor’s total L3 cache size.
- Page 160 If enabled, will allow your computer to use Executive CPU XD Support Display (XD) to hinder software that exploits buffer overflows. If enabled, limits the maximum value the processor Limit CPUID Value CPUID function will support. If enabled, allows your computer to use all cores Multi Core Support available in the processor.
- Page 161 Power If enabled, will wake the system using a network Wake Up by Integrated message LAN/WLAN Allows you to select the action the computer takes AC Recovery when power is restored. Allows you to configure the DeepSx mode. DeepSx Power Policies Allows you to charge USB devices when the USB PowerShare in S4/S5 computer is in S4/S5 state.
-
Page 162: Changing Boot Sequence
Changing Boot Sequence for the Current Boot You can use this feature to change the current boot sequence, for example, to boot from the optical drive to run Dell Diagnostics from the Drivers and Utilities disc. The previous boot sequence is restored at the next boot. -
Page 163: Clearing Forgotten Passwords
11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Remove the back cover. See "Removing the Back Cover" on page 19. -
Page 164: Clearing Cmos Settings
11. After working inside your computer, follow the instructions in "After Working Inside Your Computer" on page 13. For additional safety best practices information, see the Regulatory Compliance Homepage at dell.com/ regulatory_compliance. Remove the back cover. See "Removing the Back Cover" on page 19. -
Page 165: Flashing The Bios
• Choose from My Products and Services List • Choose from a list of all Dell products Click Continue and follow the instructions on the screen. A list of results appears on the screen. Click BIOS. Click Download File to download the latest BIOS file. - Page 166 Flashing the BIOS...