Related Manuals for D-Link 1016T - DGS Switch
Summary of Contents for D-Link 1016T - DGS Switch
- Page 1 DGS-1016T ® D-Link DGS-1024T 16/24-Port 10/100/1000Mbps Gigabit Ethernet Switch Manual Building Networ ks for People RECYCLABLE (July 2009)
-
Page 2: Fcc Warning
Reproduction in any manner whatsoever without the written permission of D-Link Corporation is strictly forbidden. Trade marks used in this text: D-Link and the D-LIN K logo are trade marks o f D-Link Corporation; Microsoft and W indows are registered trademarks o f Microsoft Corporation. -
Page 3: Table Of Contents
CONTENTS PREFACE ..............O TES O TICES AUTIO NS ..................AFETY NSTRUCTIO NS Safety Cautions....................v General Precautions for Rack-Mountable Products ......vii Protecting Against Electrostatic Discharge..........ix INTRODUCTION ..................10 WITCH ESCRIPTIO N Switch Features ...................11 Gigabit Ethernet Technology..............12 802.1P and QoS ..................13 ...........14 REEN TH ERNET... -
Page 4: Preface
D-Link DGS-1016T/DGS-1024T Unmanaged Gigabit Ethernet Switch Preface The DGS-1016T/DGS-1024T Manual is divided into sections that describe the system installation and operating instructions with examples. Section 1, Introduction - A description of the physical features of the Switch, including LED indicators, ports and panel descriptions. -
Page 5: Safety Instructions
D-Link DGS-1016T/DGS-1024T Unmanaged Gigabit Ethernet Switch Safety Instructions Use the following safety guidelines to ensure your own personal safety and to help protect your system fro m potential damage. Throughout this safety section, the caution icon ( ) is used to indicate cautions and precautions that you need to review and follow. - Page 6 D-Link DGS-1016T/DGS-1024T Unmanaged Gigabit Ethernet Switch Safety Instructions (continued) • Operate the product only from the type of external power source indicated on the electrical ratings label. If you are not sure of the type of power source required, consult your service provider or local power company.
-
Page 7: General Precautions For Rack-Mountable Products
D-Link DGS-1016T/DGS-1024T Unmanaged Gigabit Ethernet Switch Safety Instructions (continued) • Move products with care; ensure that all casters and/or stabilizers are firmly connected to the system. Avoid sudden stops and uneven surfaces. General Precautions for Rack-Mountable Products • Observe the following precautions for rack stability and safety. Also refer to the rack installation documentation accompanying the system and the rack for specific caution statements and procedures. - Page 8 D-Link DGS-1016T/DGS-1024T Unmanaged Gigabit Ethernet Switch Safety Instructions (continued) • Always load the rack from the bottom up, and load the heaviest item in the rack first. • Make sure that the rack is level and stable before extending a component from the rack.
-
Page 9: Protecting Against Electrostatic Discharge
D-Link DGS-1016T/DGS-1024T Unmanaged Gigabit Ethernet Switch Protecting Against Electrostatic Discharge Static electricity can harm delicate components inside your system. To prevent static damage, discharge static electricity from your body before you touch any of the electronic components, such as the microprocessor. You can do so by periodically touching an unpainted metal surface on the chassis. -
Page 10: Introduction
SECTION 1 Introduction Switch Description Switch Features D-Link Green Ethernet Technology Ports Front-Panel Components LED Indi cators Power Input on Rear Panel Switch Description The 16-port DGS-1016T and 24-port DGS-1024T Switches provide dedicated 10, 100 or 1000 Mbps Ethernet bandwidth on each port. The ports will automatically detect the speed, duplex and MDI/M DIX status of the device it is connecting to, and adjust these settings accordingly. -
Page 11: Switch Features
• Sixteen (DGS-1016T) or twenty-four (DGS-1024T) 10/ 100/1000Mbps Ethernet ports • Cable d iagnostics function at Switch boot up • D-Link Green Ethernet Technology • Auto-Negotiation for 10/100/ 1000Mbps and duplex mode • Auto-MDI/MDI-X for each port • Supports Full/ Half-duplex transfer mode for 10 and 100Mbps •... -
Page 12: Gigabit Ethernet Technology
Gigabit Ethernet Technology Gigabit Ethernet is an extension of IEEE 802.3 Ethernet utilizing the same packet structure, format, and support for C SMA/CD protocol, full duplex, flow control, and management objects, but with a tenfold increase in theoretical throughput over 100-Mbps Fast Ethernet and a hundredfold increase over 10-Mbps Ethernet. -
Page 13: 802.1P And Qos
802.1P and QoS The DGS-1024T and DGS-1016T Switches support 802.1p priority queuing Quality of Service. The imp lementation of QoS (Quality of Service) and benefits of using 802.1p priority queuing are described here. Advantages of QoS QoS is an implementation of the IEEE 802.1p standard that allows network administrators a method of reserving bandwidth for important functions that require a large bandwidth or have a high priority, such as VoIP (voice-over Internet Protocol), web browsing applications, file server applications or video... -
Page 14: D-Link Green Ethernet Technology
The Switch uses strict priority for Scheduling. Strict priority-based scheduling, any packets residing in the higher priority queues are transmitted first. D-Link Green Ethernet Technology D-Link Green Ethernet imp lements special power-saving features under speed at 1000Mbps that detect cable length and link status and adjust power usage accordingly. - Page 15 Method 2: D-Lin k Green Ethernet detects the length of connected Ethernet cable and adjusts power usage accordingly without affecting performance. This way, a port connected to a 10m cable only uses as much power as it needs, instead of using full power, wh ich is only needed for 100m cables.
-
Page 16: Front-Panel Components
Front-Panel Components Note: The Switch illustrations used for this manual depict only the model DGS-1016T Switch. On the front panel of the Switch you will see the following. • LED status indicators • 16 Auto-Negotiating 10/ 100/ 1000Mbps ports on the DGS-1016T •... -
Page 17: Cable Diagnostics
Cable Diagnostics Upon booting up the Switch, a Cable Diagnostics is used to detect two problems that may prevent successful connection. This feature operates only on ports that are connected to 1000Mbps devices. If there are problems on a port connected to a Gigabit Ethernet device (1000Mbps), try restarting the Switch and watch the speed (100/ 1000Mbps) LED indicators to determine is the problem is a fault in the cable or connecting hardware. - Page 18 LED Indicator Description Power This lights green while the Switch is receiving power. Link/Act A steady green light indicat es the corresponding port is connected and a valid link is established. This will blink green when there is activity on the port. 100Mbps/1000Mbps The speed indicator will light green if the corresponding port is connected and...
-
Page 19: Power Input On Rear Panel
Power Input on Rear Panel The power cable connection is located on the rear panel of the Switch. Rear panel view of the Switch Switch power input is provided by and internal universal power supply (100-240VA C : 12V/ 3.3A). The AC power connector is a standard three -pronged connector that supports the power cord. -
Page 20: Installation
SECTION 2 Installation Package Contents Before You Connect to the Network Installing the Switch Power On Package Contents Open the shipping carton of the Switch and carefully unpack its contents. The carton should contain the follo wing items: • One DGS-1016T 16-Port/DGS-1024T 24-Port 10/ 100/1000BASE-T Gigab it Ethernet Switch •... -
Page 21: Before You Connect To The Network
Before You Connect to the Network The site where you install the Switch may great ly affect its performance. Please follow these guidelines for setting up the Switch. • Install the Switch on a sturdy, level surface that can support at least 3 kg (6.6 lbs) of weight. -
Page 22: Mounting The Switch On A Rack
Mounting the Switch on a Rack The DGS-1016T/1024T can easily be mounted on a rack. Two mounting ears are provided for this purpose. Make sure that the front panel is exposed in order to view the LEDs. Please refer to the following illustrations: Mounting the Switch to a Rack Attach the ears to each side of the Switch, using the screw-holes located on the side of the device. -
Page 23: Attaching The Rubber Feet
Attaching the Rubber Feet Use rubber feet provided. Position and apply rubber feet to the underside of the DGS-1016T/1024T Switch. Attaching the Rubber Feet Provide for Adequate Ventilation CAUTION: Do not place any device on top of S witch, or place the Switch on top of any devic e or object that will block the free flow of air through the ventilation slots on the sides, top, and bottom of the S witch’s case. -
Page 24: Power On
Power On To power on the Switch, Plug-in the female connector of the provided power cord into this socket, and the male side of the cord into a suitable power source. After the Switch is powered on, the LED indicators will blink briefly while the system resets. -
Page 25: Connecting The Switch
Section 3 Connecting the Switch Connect to End Node Connect to Hub or Switch Connect to Network Backbone or S erver NOTE: All Ethernet ports auto-det ect MDI-II/MDI-X, port speed (10, 100, 1000Mbps) and duplex of the devic e connected to the Switch. Cable Quality For all connections to the Switch, use these rules to determine the •... -
Page 26: Connect To End Node
Connect to End Node End nodes include PCs outfitted with a 10, 100 or 1000 Mbps RJ-45 Ethernet/Fast Ethernet Net work Interface Card (NIC) and Ethernet ready routers. Use standard Ethernet cable to connect the Switch to end nodes. Switch ports will auto matically adjust to the hardware characteristics (MDI-II/MDI-X, speed, duplex) of the device to which it is connected. -
Page 27: Connect To Hub Or Switch
Connect to Hub or Switch Connect to another switch or hub Observe the guidelines for cable quality stated at the beginning of th is section. The Link/Act LEDs fo r each port lights green when the link is valid. -
Page 28: Connect To Network Backbone Or Server
Connect to Network Backbone or Server Any port may be used to uplink the Switch to a network backbone or network server. When linking to a 1000BASE-T device the port operates in full duplex mode. Connection to a Server Observe the guidelines for cable quality stated at the beginning of th is section. The Link/Act LEDs fo r each port lights green when the link is valid. -
Page 29: Technical Specifications
Appendix Technical Specifications General IEEE 802.3 10BASE-T Standards: IEEE 802.3u compliance IEEE 802.3ab compliance IEEE 802.1p compliance Half or Full-Duplex operations at 10/100Mbps Full-Duplex operations at 1000Mbps IEEE 802.3x Flow Control supports for Full Duplex Support back pressure for Half-Duplex operation Protocol: CSMA/CD Data Transfer... -
Page 30: Physical And Environmental
Physical and Environmental 100~240V AC; 50/60Hz AC Inputs: Internal universal power supply DGS-1024T: 19.1 Watts Power Consumption: DGS-1016T: 13.4 Watts Operating 32°F ~ 104F ° (0 °C ~ 40 ºC) Temperature: Storage Temperature: 14°F ~ 158°F (-10°C ~ 70°C) Humidity: 5% ~ 90% RH, non-condensing 19-inch, 1U Rack-mount size Dimensions:... -
Page 31: Glossary
Glossary 1000BASE-T - 1000BASE-T - Known as IEEE 802.3ab which is a standard for Gigabit Ethernet over copper wiring. 100BASE-TX – 100Mbps Ethernet implementation over Category 5 and Type 1 T wisted Pair cabling. 10BASE-T – The IEEE 802.3 specification for Ethernet over Unshielded T wisted Pair (UTP) cabling. - Page 32 Data center switching – The point of aggregation within a corporate network where a switch provides high-performance access to server farms, a high-speed backbone connection, and a control point for network management and security. Ethe rnet – A LAN specification developed jointly by Xerox, Intel, and Digital Equipment Corporation.
- Page 33 RPS – Redundant Power System. A device that provides a backup source of power when connected to the Switch. Serve r farm – A cluster of servers in a centralized location serving a large user population. SLIP – Serial Line Internet Protocol. A protocol that allows IP to run over a serial line connection.