hit counter script

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Summary of Contents for Barco R9001490

  • Page 9: Safety Instruction Related To Elm Projectors

    Safety SAFETY INSTRUCTION RELATED TO ELM PROJECTORS 5976072 BARCOELM R12 05052000...
  • Page 10 Safety 5976072 BARCOELM R12 05052000...
  • Page 11: Packaging And Dimensions

    Packaging and Dimensions PACKAGING AND DIMENSIONS Pull To open 3 7 9 5976072 BARCOELM R12 07012000...
  • Page 12: Front View

    Packaging and Dimensions FRONT VIEW Protects sides while turning over the projector Shaft for lifting Dual stack interlocking AIR OUT AIR IN Adjustable feet fork-lift slots (nominal) IR-receiver (both in front and at the rear of the projector) 5976072 BARCOELM R12 07012000...
  • Page 13: Side View

    Packaging and Dimensions SIDE VIEW 1420 190,5 Fasteners left and right Dual stack Interlocking 1314 TOP VIEW AIR OUT Zone needed for Side Panel removal (Both Left AND Right) Mains Input & Local Keypad Digital & Analog Inputs Power Switch &...
  • Page 14 Packaging and Dimensions 5976072 BARCOELM R12 07012000...
  • Page 16 Front/Ceiling Rear/Ceiling Rear/Table Front/Table...
  • Page 17 Table/Top side facing ceiling Table/Top side facing floor Projector SIDE VIEW SIDE VIEW Projector Screen Optical axis projection lens Screen Optical axis projection lens Floor Floor CD = SH/2 + B + A - 554mm CD = SH/2 + B - A Screen Screen TOP VIEW...
  • Page 18 AIR IN IR OUT Safety area for air in & out...
  • Page 22 é ê...
  • Page 23 3 1 0 a .D R W...
  • Page 26 Connections CONNECTIONS D i a g n ost i c C od e I R - Re cei ver G r e en Op era ti o n R ed S t and - b y S T A ND B Y E X I T T w o w a y ha rdw i r e d...
  • Page 27 Connections REMAINING LAMP RUN TIME 30 hours WARNING Lamp run time is 500 hours Operating the lamp longer than 500 hours may damage the projector. Please replace the lamp <ENTER> to continue WARNING Lamp run time is 400 hours. The light output of the lamp is less than 50% of its initial value.
  • Page 28 Connections Input Source Connection Diagnostic Code IR-Rec eiver Green Operation Red Stand-by Two way hardwired Hardwired remote remote CTRL 2 O U T O U T CTRL 3 Sync OK Har dwired remote RS232/422 IN RS232/422 OUT COMM PORT TRIGGER OUT CTRL 1 H / C H / C...
  • Page 29 Connections Diagnostic Code IR-Rec eiver Green Operation Red Stand-by Two way hardwired Hardwired remote remote O U T O U T CTRL 2 CTRL 3 Sync OK Hardwired remote RS232/422 IN RS232/422 OUT COMM PORT TRIGGER OUT CTRL 1 H / C H / C H / C High Bandwi d th RGB ANALOG INPUT...
  • Page 30: Installation

    Connections Diagnostic Code IR-Receiver Green Operation Red Stand-by Two way Hardwired hardwired rem ote rem ote CTRL 2 O U T O UT CTRL 3 Sync OK Hardwired rem ote RS232/422 IN RS232/422 OUT COM M PO RT TRIGGER OUT CTRL 1 H / C H / C...
  • Page 31 Connections Diagnostic Code IR-Rec eiver Green Operation Red Stand-by Two way hardwired Hardwired remote remote CTRL 2 CTRL 3 Sync OK Hardwired remote RS232/422 IN RS232/422 OUT COMM PORT TRIGGER OUT CTRL 1 H / C H / C H ig h B a n d w idt h 5 C A B LE I NP UT H ig h B a nd w id th R G B A N A LO G I N PU T é...
  • Page 32 Connections S -VID E O V ID E O A U D IO Diagnostic Code IR-Receiv er Green Operation Red Stand-by Two way hardwired Har dwired remote remote O U T O U T CTRL 2 CTRL 3 Sy nc OK Hardwired remote RS232/422 IN...
  • Page 33 Connections é ê é ê é ê ADJUSTMENT MODE INSTALLATION INPUT SLOTS Slot Module type [Config] Select a path from below : INPUT SLOTS 800 PERIPHERAL 1. RGB-SS [CV] CONFIGURATION 2. RGB-SOG RANDOM ACCESS OSD COLOR 3. Video [Video] INSTALLATION INTERNAL PATTERNS 4.
  • Page 34 Connections H / C Diagnostic Code IR-Receiver Green Operation Red Stand- by Two way hardwired Hardwired remote remote O U T O U T CTRL 3 CTRL 2 Sync OK Hardwired remote RS232/422 OUT COMM PORT TRIGGER OUT RS232/422 IN CTRL 1 H / C H / C...
  • Page 35 Connections INSTALLATION ADJUSTMENT MODE INPUT SLOTS INPUT SLOTS Slot Module type [Config] Select a path from below : 800 PERIPHERAL CONFIGURATION 1. RGB-SS [CV] OSD COLOR 2. RGB-SOG RANDOM ACCESS INTERNAL PATTERNS 3. Video [Video] INSTALLATION NO SIGNAL 4. Component Video SERVICE LENS 5.
  • Page 36 Connections R -Y B -Y Diagnostic Code IR-Receiver Green Operation Red Stand-by Two way hardwired Hardwired remote remote O U T O U T CTRL 3 CTRL 2 Sy nc OK Hardwired remote RS232/422 IN RS232/422 OUT COMM PORT TRIGGER OUT CTRL 1 H / C H / C...
  • Page 37 Connections Ay‚h‡vtÂ…Á ‚Ãsy‚h‡v tÃvƒˆ‡ Non-Floating Floating T’pÆryrp‡v‚ U …vyr‰ryÃT’p H / C Diagnostic Code IR-Receiver Green Operation Red Stand-by Two way hardwired Hardwired remote remote O U T O U T CTRL 3 CTRL 2 Sy nc OK Hardwired remote RS232/422 IN RS232/422 OUT COMM PORT...
  • Page 38 Connections E ' ÃT ’  p Æ r yr p ‡v‚  T rƒ h…h‡ rÆ ’  p T ’  p   Ãt …rr  Non-Floating Floating Ay‚h‡vtÂ…Á‚Ãsy‚h‡vtÃvƒˆ‡ 4-13 5976072 BARCOELM R12 05052000...
  • Page 39 Connections Green Operation Diagnos tic Code IR-Receiver Red Stand-by Two way hardwired Hardwired remote remote O U T O U T CTRL 2 CTRL 3 Sync OK Hardwired COMM PORT TRIGGER OUT remote RS232/422 IN RS232/422 OUT CTRL 1 H / C H / C H / C H ig h B a ndw i d th RG B A N A L OG IN P UT...
  • Page 40 Connections RS232 Connections Diagnostic Code IR-Rec eiver Green O peration Red Stand-by Two way Hardwired hardwired remote remote O U T O U T CTRL 2 CTRL 3 Sync OK Hardwired COMM PORT TRIGGER OUT remote RS232/422 IN RS232/422 OUT CTRL 1 H / C H / C...
  • Page 41 Connections Trigger output 4-16 5976072 BARCOELM R12 05052000...
  • Page 42: Getting Started

    Getting Started GETTING STARTED +(/3 EXIT STANDBY ENTER TEXT PAUSE SHARPN TINT BRIGHTN PHASE COLOR 3 2a 5976072 BARCOELM R12 17012000...
  • Page 43 Getting Started 5976072 BARCOELM R12 17012000...
  • Page 44 Getting Started +( /3 STANDBY EXIT ENTER TEXT PAUSE SHARPN TINT BRIGHTN PHASE COLOR 32 a REMAINING LAMP RUN TIME 30 h WARNING Lamp run time is 500 hours Operating the lamp longer than 500 hours may damage the projector. Please replace the lamp <ENTER>...
  • Page 45: Adjustment Mode

    Getting Started WARNING Lamp run time is 400 hours. The light output of the lamp is less than 50% of its initial value. It is advisable to replace the lamp before damage occurs. <ENTER> to confirm é ê é ê é...
  • Page 46: Lens Adjustment Zoom/Focus

    Getting Started é ê ç è LENS ADJUSTMENT ZOOM/FOCUS ZOOM with éor ê çor è é ê ç è LENS ADJUSTMENT SHIFT SHIFT with éor ê çor è é ê TILT Tilt with é,ê 5976072 BARCOELM R12 17012000...
  • Page 47 Getting Started é ê é ê é ê ADJUSTMENT MODE INSTALLATION OSD COLOR HIGHLIGHTED ITEM Select a path from below : INPUT SLOTS 800 PERIPHERALS CONFIGURATION GREEN RANDOM ACCESS OSD COLOR YELLOW INSTALLATION NO SIGNAL SERVICE INTERNAL PATTERNS LENS Source 01 Select with é...
  • Page 48 Getting Started Green Operation Diagnostic Code IR-Rec eiver Red Stand-by Two way Hardwired hardwired remote remote O U T O UT CTRL 3 CTRL 2 Sy nc OK Hardwired remote RS232/422 IN RS232/422 OUT COMM PORT TRIGGER OUT CTRL 1 H / C H / C H / C...
  • Page 49 Getting Started IR sensor IR sensor Side of projector Rear of projector Table Front of projector 45° 45° 45° 45° 45° 45° E X I T A D D R S T B Y M U T E TEX T E X I T A D D R S H A R P N E SS...
  • Page 50 Getting Started PROJECTOR ADDRESS 5976072 BARCOELM R12 17012000...
  • Page 51 Getting Started 5-10 5976072 BARCOELM R12 17012000...
  • Page 52: Start Up Of The Adjustment Mode

    Start up of the Adjustment Mode START UP OF THE ADJUSTMENT MODE ADJUSTMENT MODE Select a path from below : RANDOM ACCESS INSTALLATION SERVICE Source 01 Select with é or ê then <ENTER> <EXIT> to return. PASSWORD ENTER PASSWORD ---- Use numeric keys <EXIT>...
  • Page 53 Start up of the Adjustment Mode Error Invalid password <EXIT> to return 5976072 BARCOELM R12 17012000...
  • Page 54: Random Access Adjustment Mode

    Random Access Adjustment Mode RANDOM ACCESS ADJUSTMENT MODE ADJUSTMENT MODE Select a path from below : RANDOM ACCESS INSTALLATION SERVICE Source 01 Select with é or ê then <ENTER> <EXIT> to return. 5976072 BARCOELM R12 17012000...
  • Page 55 Random Access Adjustment Mode é ê RANDOM ACCESS FILE SERVICE ADJUSTMENT MODE LOAD FILE SERVICE EDIT PICTURE TUNING RENAME GEOMETRY COPY DELETE OPTIONS Select with é or ê Select with é or ê then <ENTER> then <ENTER> <EXIT> to return. <EXIT>...
  • Page 56 Random Access Adjustment Mode é ê è ç FILE SERVICE LOAD FILE FILTER LIST [All] LOAD Filename Resolution EDIT ----------------------------------------------------- RENAME Video525.s01 1 675x240i COPY Video525.c01 1 675x240i DELETE Video525.c02 1 675x240i OPTIONS ----------------------------------------------------- Active file : Video525.c50 Select with é or ê Select with é...
  • Page 57 Random Access Adjustment Mode é ê FILE SERVICE EDIT FILE LOAD Filename Resolution EDIT ----------------------------------------------------- RENAME Video525.s01 1 675x240i COPY Video525.c01 1 675x240i DELETE Video525.c02 1 675x240i OPTIONS ----------------------------------------------------- Active file : Video525.c50 Select with é or ê Select with é or ê , è then <ENTER>...
  • Page 58 Random Access Adjustment Mode EDIT FILE OPTIONS Source number Clamp position [leading] Clamp delay Clamp width Field polarity [pos] Field select [both] Vertical refresh [sync] Vert. sync polarity [leading] Select with é or ê <ENTER> to toggle ç or è to change value <EXIT>...
  • Page 59 Random Access Adjustment Mode CONFIRM EDIT FILE Save changes to file xga.c30? <ENTER> to confirm <EXIT> to return é ê é ê RENAME FILE RENAME FILE FILE SERVICE Filename Resolution Frome file name : LOAD ----------------------------------------------------- Video525.s01 EDIT Video525.s01 1 675x240i To file name : RENAME...
  • Page 60 Random Access Adjustment Mode ç è é ê RENAME FILE Frome file name : Video525.s01 To file name : demo.c10 Select with ç or è Reprogram with é or ê or numeric keys <ENTER> to confirm <EXIT> to return é ê...
  • Page 61 Random Access Adjustment Mode é ê é ê FILE SERVICE DELETE FILE CONFIRM DELETE FILE LOAD Filename Resolution EDIT ----------------------------------------------------- Delete file: RENAME Video525.s01 1 675x240i Video525.c01? COPY Video525.c01 1 675x240i DELETE Video525.c02 1 675x240i OPTIONS [ALL] ----------------------------------------------------- Active file : Video525.c50 Select with é...
  • Page 62 Random Access Adjustment Mode é ê PICTURE TUNING RANDOM ACCESS ADJUSTMENT MODE CTI [ON] COLOR TEMPERATURE FILE SERVICE GAMMA PICTURE TUNING DECODING [EBU] GEOMETRY DYNAMIC COLOR DEPTH NOISE REDUCTION INPUT BALANCE Select with é or ê Select with é or ê then <ENTER>...
  • Page 63 Random Access Adjustment Mode é ê PICTURE TUNING COLOR TEMPERATURE CTI [ON] PROJECTOR WHITE COLOR TEMPARATURE COMPUTER 9300K GAMMA VIDEO 6500K DECODING [EBU] FILM 5400K DYNAMIC COLOR DEPTH BROADCAST 3200K NOISE REDUCTION INPUT BALANCE CUSTOM BALANCE Select with é or ê Select with é...
  • Page 64 Random Access Adjustment Mode é ê ç è PICTURE TUNING GAMMA = 2.2 CTI [ON] COLOR TEMPERATURE GAMMA DECODING [EBU] DYNAMIC COLOR DEPTH NOISE REDUCTION INPUT BALANCE Select with é or ê then <ENTER> <EXIT> to return. é ê PICTURE TUNING CTI [ON] COLOR TEMPERATURE GAMMA...
  • Page 65 Random Access Adjustment Mode é ê ç è PICTURE TUNING NOISE REDUCTION CTI [ON] COLOR TEMPERATURE GAMMA DECODING [EBU] DYNAMIC COLOR DEPTH NOISE REDUCTION INPUT BALANCE Select with é or ê then <ENTER> <EXIT> to return. é ê é ê é...
  • Page 66 Random Access Adjustment Mode é ê RANDOM ACCESS GEOMETRY ADJUSTMENT MODE SHIFT FILE SERVICE SIZE PICTURE TUNING SIDE KEYSTONE GEOMETRY BLANKING OPTIONS Select with é or ê Select with é or ê then <ENTER> then <ENTER> <EXIT> to return. <EXIT> to return. é...
  • Page 67 Random Access Adjustment Mode é ê é ê ç è GEOMETRY Fixed sides SHIFT Horizontal size SIZE adjustment SIDE KEYSTONE BLANKING ASPEC RATIO [4:3] OPTIONS Select with then <ENTER> <EXIT> to return. Vertical size adjustment é ê ç è ç è...
  • Page 68 Random Access Adjustment Mode Top blanking Right blanking Left blanking Bottom blanking é ê é ê BLANKING GEOMETRY SHIFT BOTTOM SIZE LEFT SIDE KEYSTONE RIGHT BLANKING ASPEC RATIO [4:3] OPTIONS Select with é or ê Select with é or ê then <ENTER>...
  • Page 69: Geometry Options

    Random Access Adjustment Mode é ê GEOMETRY SHIFT SIZE SIDE KEYSTONE BLANKING ASPEC RATIO [4:3] OPTIONS Select with é or ê then <ENTER> <EXIT> to return. é ê GEOMETRY OPTIONS GEOMETRY Use the same side SHIFT keystone correction SIZE for all files ? SIDE KEYSTONE [YES] BLANKING...
  • Page 70: Installation Mode

    Installation Mode INSTALLATION MODE é ê ENTER ADJUSTMENT MODE INSTALLATION Select a path from below : INPUT SLOTS 800 PERIPHERAL CONFIGURATION RANDOM ACCESS OSD COLOR INSTALLATION INTERNAL PATTERNS SERVICE NO SIGNAL LENS Source 01 QUICK ACCESS KEYS Select with é ê...
  • Page 71: Installation

    Installation Mode é ê ENTER é ê ENTER INSTALLATION 800 PERIPHERAL INPUT SLOTS 800 PERIPHERAL OUTPUT MODULE [STANDARD] CONFIGURATION INFRARED [PPM] OSD COLOR INTERNAL PATTERNS NO SIGNAL LENS QUICK ACCESS KEYS Select with é ê MENU POSITION [DEFAULT] <ENTER> to toggle Select with é...
  • Page 72 Installation Mode é ê ENTER é ê ENTER INSTALLATION INPUT SLOTS 800 PERIPHERAL CONFIGURATION OSD COLOR INTERNAL PATTERNS NO SIGNAL LENS QUICK ACCESS KEYS MENU POSITION [DEFAULT] Select with é ê then <ENTER> <EXIT> to return. é ê ENTER é ê...
  • Page 73 Installation Mode é ê ENTER é ê ENTER INSTALLATION NO SIGNAL COLOR [Blue] INPUT SLOTS SHUTDOWN [Off] 800 PERIPHERAL CONFIGURATION Shutdown time : 5 min OSD COLOR INTERNAL PATTERNS NO SIGNAL LENS QUICK ACCESS KEYS MENU POSITION [DEFAULT] Select with é ê...
  • Page 74 Installation Mode é ê ENTER é ê ENTER INSTALLATION INTERNAL PATTERNS INPUT SLOTS OUTLINE 800 PERIPHERAL HATCH CONFIGURATION COLOR BARS MULTIBURST OSD COLOR CHECKER BOARD INTERNAL PATTERNS PURITY NO SIGNAL LENS PAGE CHAR QUICK ACCESS KEYS ALPHA-NUMERIC CHARS Select with é ê...
  • Page 75 Installation Mode é ê é ê ç è EXIT ENTER LENS ADJUSTMENT ZOOM/FOCUS SHIFT TILT BRIDGE OPTIONS LENS Select with é or ê LENS ADJUSTMENT ZOOM/FOCUS then <ENTER> ZOOM with éor ê <EXIT> to return. çor è ENTER é ê ENTER é...
  • Page 76 Installation Mode é ê ENTER é ê LENS ADJUSTMENT BRIDGE Open with é ZOOM/FOCUS Close with ê SHIFT TILT BRIDGE OPTIONS Select with é or ê then <ENTER> <EXIT> to return. é ê ENTER ENTER LENS ADJUSTMENT LENS OPTIONS ZOOM/FOCUS Use the same SHIFT zoom, focus and shift...
  • Page 77 Installation Mode é ê ENTER INSTALLATION INPUT SLOTS 800 PERIPHERAL CONFIGURATION OSD COLOR INTERNAL PATTERNS NO SIGNAL LENS QUICK ACCESS KEYS MENU POSITION [DEFAULT] Select with é ê then <ENTER> <EXIT> to return. 5976072 BARCOELM R12 05052000...
  • Page 78: Service Mode

    Service Mode SERVICE MODE é ê ENTER ADJUSTMENT MODE SERVICE SERVICE Select a path from below : IDENTIFICATION BARCO LOGO CHANGE PASSWORD PRESET INPUT BALANCE CHANGE LANGUAGE ADD INS RANDOM ACCESS CHANGE PROJ. ADDRESS I2C DIAGNOSIS INSTALLATION SERIAL COMMUNICATION SERVICE LAMP MORE...
  • Page 79 Service Mode SERVICE PRESET INPUT BALANCE BARCO LOGO IDENTIFICATION WHITE BALANCE STATUS : [ON] BLACK BALANCE BACKGROUND : [ON] CHANGE PASSWORD CHANGE LANGUAGE SHIFT CHANGE PROJ. ADDRESS DEFAULT HOT KEY : [TEXT] SERIAL COMMUNICATION LAMP Select with <ENTER> MORE... <EXIT> to return Adjust Select with é...
  • Page 80 Service Mode 5976072 BARCOELM R12 05052000...
  • Page 81 CHANGE PASSWORD OWNER 0000 CHANGE LANGUAGE USER 0000 Adjustment mode Y Y Y Y CHANGE PROJ. ADDRESS GUEST 0000 Barco logo SERIAL COMMUNICATION Change Proj. Address Y Y - LAMP ACCESS CONTROL LIST MORE... Select with é or ê then <ENTER>...
  • Page 82 Service Mode é ê ENTER SERVICE CHANGE LANGUAGE IDENTIFICATION English CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJ. ADDRESS SERIAL COMMUNICATION LAMP MORE... Select with é or ê then <ENTER> <EXIT> to return. Select with é or ê then <ENTER> <EXIT> to return. é...
  • Page 83 Service Mode é ê ENTER SERIAL COMMUNICATION PROJECTOR ADDRESS 001 BAUDRATE [115200] INTERFACE STANDARD [RS232] RS422 TERMINATION [ON] Select with é or ê then <ENTER> <EXIT> to return. é ê ENTER SERIAL COMMUNICATION PROJECTOR ADDRESS 001 BAUDRATE [115200] INTERFACE STANDARD [RS232] RS422 TERMINATION [ON] Select with é...
  • Page 84 <ENTER> <ENTER> to toggle <EXIT> to return. <EXIT> to return. é ê é ê ENTER SERVICE BARCO LOGO BARCO LOGO STATUS : [ON] PRESET INPUT BALANCE BACKGROUND : [ON] ADD-INS SHIFT I2C DIAGNOSIS HOT KEY : [TEXT] MORE... Select with é or ê...
  • Page 85: Preset Input Balance

    Service Mode é ê ENTER SERVICE WARNING BARCO LOGO RESET INPUT BALANCE ADD-INS I2C DIAGNOSIS PRESET INPUT BALANCE is reserved to MORE... qualified service personnel <ENTER> to accept Select with é or ê <EXIT> to return. then <ENTER> <EXIT> to return.
  • Page 86 ENTER é ê,ç è ENTER SERVICE ADD-INS INSTALL ADD-INS LIGHT SENSOR LIGHT SENSOR [INACTIVE] BARCO LOGO RESET INPUT BALANCE Key : xxxxxxxxxxxxxxxx ADD-INS I2C DIAGNOSIS Hardware : OK Software : Not activated MORE... Select with é or ê Select with é or ê...
  • Page 87 Service Mode 9-10 5976072 BARCOELM R12 05052000...
  • Page 88: Programmable Function Keys

    3. Press ENTER to confirm. 4. The function key is available in the operational mode. CONFIRM QUICK ACCESS <F1> will be used to quickly access this menu. <ENTER> to confirm <EXIT> to cancel. menu 1 10-1 5976070 BARCO ELM R12 05052000...
  • Page 89 Programmable Function Keys 10-2 5976070 BARCO ELM R12 05052000...
  • Page 92 INDEX...

This manual is also suitable for:

Elm r12

Table of Contents