Where to Find Information Setup Guide This guide will help you set up and begin using your printer. It includes information on setting up your printer and installing the printer software. Daily Use Guide This guide provides information on daily printer operation.
Page 3
CORPORATION. The information contained herein is designed only for use with this EPSON printer. EPSON is not responsible for any use of this information as applied to other printers. Neither SEIKO EPSON CORPORATION nor its affiliates shall be liable to the purchaser of...
Model: P150A Conforms to the following Directive(s) and Norm(s): Directive 89/336/EEC: EN 55022 Class B EN 61000-3-2 EN 61000-3-3 EN 50082-1 Directive 73/23/EEC: EN 60950 August 1999 H. Horiuchi President of EPSON EUROPE B.V. IEC 801-2 IEC 801-3 IEC 801-4...
Do not use a damaged or frayed power cord. If you use an extension cord with the printer, make sure the total ampere rating of the devices plugged into the extension cord does not exceed the cord’s ampere rating. Also, make sure the total ampere rating of all devices plugged into the wall outlet does not exceed the wall outlet’s ampere rating.
Always turn the printer off using the P power button. When this button is pressed, the P power light flashes briefly then goes off. Do not unplug the printer or turn off the power to the outlet until the P power light stops flashing.
When choosing a place for the printer Place the printer on a flat, stable surface that is larger than the printer. The printer will not operate properly if it is tilted or at an angle.
For United Kingdom Users Use of options EPSON (UK) Limited shall not be liable against any damages or problems arising from the use of any options or consumable products other than those designated as Original EPSON Products or EPSON Approved Products by EPSON (UK) Limited.
Replace fuses only with a fuse of the correct size and rating. Warnings, Cautions, and Notes Warnings must be followed carefully to avoid bodily injury. Cautions must be observed to avoid damage to your equipment. Notes contain important information and useful tips on the operation of your printer.
Printer Parts and Functions Printer Parts and Control Panel Functions paper support edge guides printer cover output tray sheet feeder output tray extension ink cartridge clamps adjust lever control panel...
Page 14
On when the printer is on. Flashes when receiving data, printing, replacing an ink cartridge, charging ink, or cleaning the print head. On when the printer is out of paper. Load paper in the sheet feeder, then press the resume printing.
When loading special paper distributed by EPSON, read the instruction sheets packed with your special media first and keep the following points in mind. For more details on using such media, see “Paper Handling”.
Page 16
Make sure the paper stack fits under the arrow mark located on the inside surface of the left edge guide. Loading capacity for envelopes and EPSON special media is explained below. Envelopes 360 dpi Ink Jet Paper and Photo Quality Ink Jet Paper...
* Take care not to print on support sheets loaded under special media. About special media cleaning sheets Cleaning sheets packaged with EPSON special media should not be used with this printer. The cleaning function performed by these sheets is not necessary with this type of printer, and the sheets could jam in the printer.
Page 18
Do not use envelopes that are curled or folded. Make sure to flatten the envelope flaps before loading. Also avoid using envelopes that are too thin; they may curl during printing. Select Plain Paper as the Media Type setting on the printer driver. Available envelopes sizes are:...
Printer Software Introduction The printer software includes a printer driver and printer utilities. The printer driver lets you choose from a wide variety of settings to get the best results from your printer. The printer utilities help you check the printer and keep it in top condition.
When you access the printer software from the Start menu, the settings you make apply to all of your Windows applications. From Windows applications 1. Open the File menu and choose Print or Print Setup. 2. Then click Printer, Setup, Options, or Properties.
Page 21
Note: The Layout menu is available only for Windows 95, 98 and NT 4.0 users. The Mode options on the Main menu are arranged to give you four levels of control over the printer driver, as explained below. Automatic PhotoEnhance...
On the Main menu, select the Media Type setting that matches the paper you loaded in the printer. Find your paper in the list below, then select a corresponding Media Type setting (shown in larger type).
Using the Automatic mode Note: If you are using Windows 3.1, see “Making changes to printer driver settings for Windows 3.1” on page 24. When Automatic is selected on the Main menu, the printer driver takes care of all detailed settings based on the current Media Type and Ink settings.
Soft Focus Sepia Using the Custom mode Note: If you are using Windows 3.1, see “Making changes to printer driver settings for Windows 3.1” on page 24. Standard image correction for most photos. Try this setting first. Best for photos of people.
Page 27
The Custom mode offers ready-made settings designed for printing text and graphs and for applying a color-matching method. You can also create and save your own Custom settings. The Custom mode provides the following ready-made settings. Text/Graph Economy (For Windows 95 and sRGB Follow the steps below to select a Custom setting.
Previewing your printout To see a preview of your document before printing it, select the Print Preview check box on the Main menu. When you print your document, the Print Preview window appears: The Preview dialog box contains several icon buttons you can use to perform the following functions.
Page 29
Reference Guide. Selecting this option will display a rectangle on the page being previewed. This rectangle is the printable area for the page. The printer cannot print anything which exceeds this rectangle. This option displays the watermark settings dialog.
Page 30
The Add and Remove options allow you to specify which pages in the document you wish to be printed. To add or remove page, you must first highlight the page in the list of page icons appearing on the left side of the preview window. Highlight the page by clicking once on the page icon.
Making changes to printer driver settings for Windows 3.1 Using the Automatic setting When Automatic is selected on the Main menu, the printer driver takes care of all detailed settings based on the current Media Type and Ink settings. To make the Ink setting, click Color to print in color, or Black to print in black-and-white or grayscale.
Page 32
The Custom settings let you make a wide range of changes with a single click of the mouse. In the Custom settings list, you’ll find ready-made settings provided by EPSON designed to match a particular kind of printout, such as graphs and charts used in a presentation, or images taken by a digital camera.
Windows 95 and 98) or EPSON Printers (for Windows NT 4.0), then click EPSON Stylus COLOR 860 Help. The help contents window appears. Accessing help from Windows 3.1 Open the EPSON group and click the EPSON Stylus COLOR 860 Help icon. The help contents window appears.
Printer Software Introduction The printer software includes a printer driver and printer utilities. The printer driver lets you choose from a wide variety of settings to get the best results from your printer. The printer utilities help you check the printer and keep it in top condition.
In the Print dialog box, select the Media Type setting that matches the paper you loaded in the printer. Find your paper in the list below, then select a corresponding Media Type setting (shown in larger type).
Using the Automatic settings When Automatic is selected as the Mode option in the Print dialog box, the printer driver takes care of all detailed settings based on the current Media Type and Ink settings. To make the Ink setting, click Color to print in color, or Black to print in black-and-white or grayscale.
Note: This mode is available only when you are printing 24 or 32 bit Color Image. Printing with Photo Enhance selected may increase print time depending on your computer system and the amount of data contained in your image. The Photo Enhance mode provides the following settings. Standard People Nature...
Preview icon button in the Print dialog box allows you to see how your document will look before actually printing it. Follow these steps to use this feature. 1. Make your printer driver settings. 2. Click the Print button changes into a Preview button.
Page 41
3. Click the Preview button. The Preview dialog box appears and displays a preview of your document. The Preview dialog box contains six icon buttons you can use to perform the following functions. Selection Zoom Margin Display/ Non- Display Watermark Editing Add Page Remove...
Save As box and click Save. When you want to print the data, double-click the file to open EPSON Monitor 3. Click the to the printer. Save File modes. Click the icon to select the mode...
Replacing Ink Cartridges The printer’s indicator lights will inform you when it is time to obtain a replacement ink cartridge and when it is time to replace an empty cartridge. You can also check ink levels and start the ink cartridge replacement procedure from your computer using the Status Monitor utility.
Page 44
Caution: EPSON recommends the use of genuine EPSON ink cartridges. Other products not manufactured by EPSON may cause damage to your printer not covered by EPSON's warranties. Leave the old cartridge installed in the printer until you have obtained a replacement. Otherwise, ink remaining in the print head nozzles may dry out.
Page 45
Note: If you press the B A cleaning button for three seconds when the B black and A color ink out lights are off, the printer starts cleaning the print head. 4. Lift up the clamp that holds the cartridge you want to replace as far as it will go.
Page 46
Once you open the ink cartridge clamp, the ink cartridge becomes unusable and cannot be reinstalled, even if ink remains. 5. Lift the cartridge out of the printer and dispose of it properly. Do not take the used cartridge apart or try to refill it. Warning: If ink gets on your hands, wash them thoroughly with soap and water.
Page 47
Caution: You must remove the yellow tape seal from the cartridge before installing it otherwise, a fatal error will occur and the cartridge will become unusable. Do not remove the blue portion of the tape seal from the top of the cartridge; otherwise, the print head may become clogged and will be unable to print.
Page 48
9. Make sure the B black and A color lights are off, then press the B A cleaning button. The printer moves the print head and begins charging the ink delivery system. This process takes about thirty seconds to complete. When the ink charging...
For Windows users 1. Make sure A4 or Letter size paper is loaded in the sheet feeder. 2. Click the Utility tab in the printer software window, then click the Nozzle Check button. 3. Follow the instructions on your screen.
2. Make sure that A4 or Letter size paper is loaded in the sheet feeder. 3. Hold down the S load/eject button ( in the illustration below) and press the P power button ( below) to turn on the printer. Then release both buttons. in the illustration...
If the nozzle check page does not print satisfactorily (for example, if any segment of the printed lines is missing) there is a problem with the printer. This could be a clogged ink nozzle or a misaligned print head. See the next section for details on cleaning the print head.
2. Click the Utility tab in the printer software window, then click the Head Cleaning button. 3. Follow the messages on your screen. For Macintosh users 1. Make sure that the printer is on, and the B black and A color ink out lights are off.
Print head cleaning takes about thirty seconds to complete. Caution: Never turn off the printer while the P power light is flashing. Doing so may damage the printer. Utility icon button in the Print or Page Setup...
If print quality hasn’t improved after repeating this procedure four or five times, turn the printer off and leave it alone overnight. Then do the head cleaning again. If the print quality still has not improved, one or both of your ink cartridges may be old or damaged and may need to be replaced.
Page 55
3. Follow the messages on your screen to align the print head. For Macintosh users 1. Make sure A4 or Letter size plain paper is loaded in the sheet feeder. 2. Click the dialog box, then click the Print Head Alignment button. 3.
USB port or which is upgraded from Windows 95 to 98. For details about your computer, contact your dealer. Make sure that EPSON USB Printer Devices appears in the Device Manager menu If you canceled the plug-and-play driver installation before the procedure was completed, either the USB printer device driver or the printer driver may be incorrectly installed.
Page 57
If EPSON USB Printer Devices does not appear in the Device Manager menu, click the plus (+) sign beside Other Devices to view the installed devices. If USB Printer appears under Other Devices, the USB printer device driver is not installed correctly.
Page 58
4. Under Other Devices, click USB Printer or EPSON Stylus COLOR 860, then click Remove. Then click OK. 5. Unplug the USB cable from the printer, then plug it into the printer again. 6. The following dialog box appears. Install the driver again,...
Error Indicators You can identify many common printer problems with the lights on your printer’s control panel. If your printer stops working and the lights are on or flashing, use the following table of panel light patterns to diagnose the problem, then follow the recommended corrective measures.
O = on, N = off, F = flashing Typical Problems and Solutions Most printer problems have simple solutions. Find the problem in the list below and apply the recommended solution. For more information, see “Troubleshooting” in the online Reference Guide.
Make sure the printable side of the paper is face up in the sheet feeder. Run the Print Head Alignment utility. Turn off the High Speed setting in your printer driver. For instructions, see the printer driver’s online help for Windows. For Macintosh, see “Using the Advanced settings” in the online Reference Guide.
Use the recommended USB cable as described in “System Requirements” in the online Reference Guide If you use a USB hub, connect the printer to the first tier of the hub, or connect the printer to the computer’s USB port...
Software using Add/Remove Programs in the Control Panel, then uninstall the EPSON USB Printer Devices. Next, re- install the software as described in Setup Guide. If the EPSON USB Printer Devices are not registered in Add/ Remove Programs, start epusbun. exe below ¥Win9x of CD- ROM directly.
When you send a print job to the printer, the Despooler appears on your screen. Click the For Macintosh When background printing is on 1. Select EPSON Monitor3 from the application menu. 2. Press the power button to turn off the printer. Stop button to cancel printing.
(.) key to cancel the print job. Where to Get Help If your printer is not operating properly and you cannot solve the problem using the troubleshooting information in your printer documentation, contact customer support services for assistance.
Page 66
For United Kingdom and the Republic of Ireland Users If you purchased your product in the UK or the Republic of Ireland, EPSON (UK) LTD provides a range of customer services and technical support. Support Via the World Wide Web...
Page 67
Where to purchase genuine EPSON consumables, accessories, and options For Australian Users EPSON Australia wishes to provide you with a high level of Customer Service. As well as the user’s guide, we provide the following sources for obtaining information: EPSON FAXBACK EPSON FAXBACK will fax you the latest specifications and pricing for most EPSON products offered in Australia.
Page 68
EPSON Helpdesk EPSON Helpdesk is provided as a final backup to make sure our clients have access to advice. Operators on the Helpdesk can aid you in diagnosing hardware and software problems. They can also advise you on the latest EPSON products and where the nearest dealer or service agent is located.
Page 69
To obtain technical support as well as other after-sales services, users are welcome to contact EPSON Hong Kong Limited. Internet home page EPSON Hong Kong has established a local home page in both Chinese and English on the Internet to provide users with the following information:...
Page 70
(852) 2585-4399 Fax: (852) 2827-4383 For Philippines Users To obtain technical support as well as other after sales services, users are welcome to contact the EPSON Philippines Representative Office at the telephone and fax numbers below: Phone: (632) 813-6552 Fax:...
Caution: Use only interface cables which meet the specifications listed above. Using other cables not covered by EPSON warranties may cause the printer to malfunction. Consumable products The following ink cartridges and EPSON special media are...
Note: The product numbers of ink cartridges vary by location. EPSON special media EPSON offers specifically designed media for ink jet printers to meet most high-quality printing needs. EPSON Premium Ink Jet Plain Paper (A4) EPSON 360 dpi Ink Jet Paper (A4)
Page 73
EPSON Photo Paper Cards (A4) EPSON Photo Stickers 16 (A6) EPSON Photo Stickers 4 (A6) EPSON Panoramic Photo Paper (210 EPSON Iron-On Cool Peel Transfer Paper (A4) EPSON Iron-On Cool Peel Transfer Paper (Letter) EPSON Matte Paper-Heavyweight (A4) EPSON Matte Paper-Heavyweight (Letter) Note: The availability of special media varies by location.
Page 74
EPSON OVERSEAS MARKETING LOCATIONS EPSON AMERICA, INC. 20770 Madrona Ave. P.O. Box 2842 Torrance, CA 90509-2842 Phone: (800) 922-8911 Fax: (310) 782-5220 EPSON DEUTSCHLAND GmbH Zülpicher Straße 6, 40549 Düsseldorf Germany Phone: (0211) 56030 Fax: (0211) 5047787 EPSON AUSTRALIA PTY. LTD.