Related Manuals for Husqvarna Soff-Cut 4200
Summary of Contents for Husqvarna Soff-Cut 4200
- Page 1 US Operator’s manual Soff-Cut 4200 Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. HUSQVARNA CONSTRUCTION PRODUCTS...
-
Page 2: Table Of Contents
UNPACKING CONTENTS Your 4200 saw has been shipped from the factory thoroughly Content Page inspected. Only minimal assembly is required to start using Table of contents ………………………….. the saw. Remove the saw from the container using proper lift- Unpacking ..........ing techniques. -
Page 3: I Ntroduction, Personal Safety
If you have further questions you can contact the closest Husqvarna Construction Products location by writing or calling, see information below. You can also find the closest location by searching the internet at;... -
Page 4: Registration Of The Product
REGISTER THE PRODUCT Please register your new 4200 with Husqvarna Construction Products by mailing in the registration card that came with the machine or you can register on the internet site www.husqvarnawarranty.com Registration will allow us to contact in case of any critical updates or recalls on this machine. -
Page 5: Safety Warnings
• Do not operate the saw in areas of combustible material or • Use only Husqvarna Excel Series blades or blades marked fumes. Sparks may occur from the saw that could cause a fire or explosion. -
Page 6: Excel Series Blades
EXCEL SERIES BLADES The Excel Series of diamond blades have been designed specifically for the Soff-Cut Ultra Early Entry dry cutting system of green concrete. These specialty blades are designed to increase speed and life while cutting a wide range of aggregates. Choose the correct specification of diamond blade for your area as follows: Purple Excel Series 1000 XL14-1000... -
Page 7: What Is What
WHAT IS WHAT What is what? Choke Circuit breaker C. Engine on/off switch D. Emergency stop switch Tachometer Hour meter/Volt meter G. Saw forward speed switch H. Guide switch Engine speed switch Transmission neutral light Digital display Engine oil alert light M. -
Page 8: Operating Instructions
OPERATING INSTRUCTIONS Control panel To start the engine, turn the key switch (C) to the “ON” or “1” position to activate the rocker switches. Raise the saw by pushing the blade rocker switch (O) on the instrument panel to the full up position. Push the saw forward speed rocker switch Hood (G) into neutral indicated by the red light (J) on the instrument panel. - Page 9 cont... Increase the forward speed if the saw is pulling left. Decrease the forward speed if the saw is pulling right. Do not force the saw. When approaching a wall, raise the front guide and use DIGITAL DISPLAY (K) the triangle guide at the back of the blade block to cut the last The digital display in the center of the instrument panel indi- few feet.
-
Page 10: Fuel And Fuel Safety Warnings
FUEL HANDLING OIL HANDLING NOTICE WARNING Used oil is a hazardous waste product. Dispose Taking the following precautions will lessen the risk of used oil properly. Do not discard with household of injury and property damage: waste. Check with your local authorities, service center, or dealer for safe disposal/recycling facility. -
Page 11: Engine And Transmission Maintenance
ENGINE AND TRANSMISSION MAINTENANCE Engine Oil Fuel filter Checking, Adding and Changing Oil Inspect the fuel filter (F) every 50 hours. Replace the fuel filter Check the engine oil level (A) daily with saw fully lowered and annually. the engine level. See the enclosed Kohler manual for more details. -
Page 12: Other Maintenance
Skid plate Inspect the skid plate daily for damage, excessive wear in the Do not modify the saw! Use only Husqvarna Construc- blade slot, burrs on the concrete surface side, twisting and free tion Products replacement parts. Use of unauthorized movement up and down when installed on the blade block. -
Page 13: Sawing Contraction Joints
Husqvarna sawed contraction joints should be a minimum of 1/8th the concrete depth and a minimum of 1”... -
Page 14: Maximizing The Soff-Cut System
Cut is being specified more today than ever, sometimes the ultra early-entry spec is not always followed on the job site. In order for the Soff-Cut system and an experienced Husqvarna contractor to do a satisfactory job, four components must exist to meet the “specification”:... -
Page 15: Troubleshooting
- Do not force the saw. Allow the diamond blade to cut at its own rate of speed. - Use Husqvarna joint protectors at all cut intersections. - Check the skid plate for damage or burrs. - Clean excess concrete debris from the blade block assembly. -
Page 16: Technical Specifications
EC DECLARATION OF CONFORMITY Husqvarna AB, SE-433 81 Göteborg, Sweden, tel: +46-31-949000, declares under sole responsibility that the Husqvarna Soff-Cut 4200 dating from 2010 serial numbers and onwards (the year is clearly stated on the rating plate, followed by the serial number), complies with the requirements of the COUNCILíS DIRECTIVE:... -
Page 17: Warranty
The use of any other blade except Husqvarna Construction Products blades and skid plates will void the warranty and could cause internal damage to the motor. - Page 18 www.husqvarnacp.com 1153474-95 Original instructions 2009-12-29 ´®z+UOQ¶5h¨ ´®z+UOQ¶5h¨...