Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Miele G 601
Summary of Contents for Miele G 601
-
Page 1: Installation Instructions
Installation instructions for freestanding, built-under and integrated dishwashers It is essential to read the operating and installation instructions before installing or using the machine, to avoid the risk of accident or damage to the machine. M.-Nr. 05 565 043... - Page 2 These installation instructions apply to several different dishwasher models. Model numbers in this booklet refer to the model designation specified on the data plate on the machine (and not the description on the control panel). The data plate is located at the top of the door when open. The model numbers quoted refer only to the basic model number, e.g.
-
Page 3: Table Of Contents
Contents Installing a freestanding dishwasher ........4 Installing integrated "i"... -
Page 4: Installing A Freestanding Dishwasher
Depending on model the adjustment range is: – G 601 - G 632 2 cm (85-87 cm total height) – G 646 - G 698, G 975 4 cm (85-89 cm total height) -
Page 5: Installing Integrated "I" Dishwashers
Installing integrated "i" Dishwashers Integrated ("i") dishwashers To ensure stability, "i" and "U" mo- "i" dishwashers are specially designed del dishwashers must only be for building under a continuous installed under a continuous worktop worktop. which must be securely screwed to –... -
Page 6: Building In Dimensions
Installing integrated "i" Dishwashers Building in dimensions Dishwasher models G 601 - G 632 Dishwasher models G 801 - G 832 Dishwasher models G 636 - G 698, Dishwasher models G 836 - G 898 G 975 1) Niche height 890 mm... -
Page 7: Fitting Protective Cover Plate To Worktop
Installing integrated "i" Dishwashers 1. Fitting protective cover plate to worktop The underside of the worktop is protected against steam rising from the machine by a special cover plate. If two different materials meet up at the front edge of the worktop, then the join must be concealed by the cover plate. -
Page 8: Fitting The Facia Panel
Dishwashers with selector dial (G 601 - G 624, G 638 - G 686, G 801 - G 824, G 838 - G 884, G 975) ^ Attach cap a to push button switch. ^ Place the facia panel c in position... - Page 9 Installing integrated "i" Dishwashers Dishwashers with programme selector buttons (G 632, G 692 - G 696, G 832, G 892 - G 896) ^ Attach cap a to push button switch. ^ Place the facia panel c in position and use the six screws d to screw in place ^ Push the ventillation grille b into through from the inside of the door.
-
Page 10: Building The Dishwasher Into A Niche
Installing integrated "i" Dishwashers 3. Building the dishwasher Dishwasher height into a niche ^ Adjust the height manually before installing the dishwasher. Connection to water and drainage Leave a space of approx. 5 mm should be sited beside and not behind below the worktop to allow the the dishwasher for accessibility. -
Page 11: Securing Pieces
Installing integrated "i" Dishwashers Securing pieces Angle connector To ensure stability, the dishwasher must The angle connector for the water be fixed securely to the worktop (step 6). drainage hose at the rear of the Two securing pieces are supplied for dishwasher can be turned. - Page 12 Installing integrated "i" Dishwashers Front screw feet Now adjust the feet until the seal on the top of the dishwasher is right up against the underside of the worktop, to which it will be screwed later. Ensure that the dishwasher stands level.
-
Page 13: Adjustment Range
Installing integrated "i" Dishwashers 4. Matching the facia panel to Adjustment range: the height of adjacent drawer from 112 mm: Facia panel fronts without spacer bars The facia panel can be aligned with the to 145 mm: Facia panel with drawer fronts by adjusting the spacer up to 4 spacer bars bars. -
Page 14: Fitting The (Matching) Door Front
If a kitchen door front is not available, a panel with the following dimensions may be used: Width: depending on model G 601 - G 632 440 - 447 mm G 801 - G 832 G 636 - G 698, G 975... - Page 15 Installing integrated "i" Dishwashers ^ Take off the fixing bracket. ^ Lay the door front down with the rear side facing upwards. ^ Hang the fixing bracket into the slits in the machine door outer panel. ^ Push the overhanging ends of the templates under the facia panel.
-
Page 16: Fitting And Securing The Door Front
Installing integrated "i" Dishwashers Fitting and securing the door front ^ Drill the fixing holes to a depth of about 10 mm, using a 2.5 mm drill ^ Hang the door front into the slits in bit. the machine door outer panel. ^ Secure the fixing bracket to the door front using the countersunk screws supplied. - Page 17 Installing integrated "i" Dishwashers ^ Adjust the door front height on one Once the door front is correctly side and lightly screw in a T20 Torx positioned: screw on this side. ^ Open the dishwasher door. ^ Adjust the door front height on the ^ Tighten all the Torx screws on the other side and also lightly screw in a sides.
-
Page 18: Securing The Dishwasher
Installing integrated "i" Dishwashers 6. Securing the dishwasher ^ Open the dishwasher door. The holes in the securing pieces must line up with the long holes in the worktop cover plate. If this is not the case, adjust the position of the dishwasher in the niche (ensure that the dishwasher is the same distance from the neighbouring kitchen units... -
Page 19: Adjusting The Door Springs
If the door front is too heavy for the door springs (i.e. the door falls open) then stronger springs should be fitted. Please contact your Miele dealer or the Miele Spare Parts Department for ^ Adjust the door spring with a Torx advice. -
Page 20: Matching The Plinth Facing Of A Kitchen Run
Installing integrated "i" Dishwashers 8. Matching the plinth facing ^ Place the plinth facing directly in front of the kitchen run but do not attach. of a kitchen run ^ Carefully open the dishwasher door. The plinth area of the dishwasher is normally covered with a plinth run If the door front comes into contact with matching the kitchen furniture. -
Page 21: Installing Built-Under "U" Model Dishwashers
Installing built-under "U" model dishwashers Built-under "U" model To ensure stability, "U" model dishwashers dishwashers must only be installed “U” model dishwashers are specially under a continuous worktop which is designed for installing under a securely screwed to neighbouring continuous worktop. units. - Page 22 Installing built-under "U" model dishwashers Building in dimensions: Dishwasher models G 836 - G 898 Dishwasher models G 636 - G 698 G 975 1) Niche height 890 mm 2) Niche height 840 mm Adjustment range approx. 5 cm (84 - 89 cm total height).
-
Page 23: Fitting Protective Cover Plate To Worktop
Installing built-under "U" model dishwashers 1. Fitting protective cover plate to worktop The underside of the worktop is protected against steam rising from the machine by a special cover plate. If two different materials meet up at the front edge of the worktop, then the join must be concealed by the cover plate. -
Page 24: Building The Dishwasher Into Its Niche
Installing built-under "U" model dishwashers 2. Building the dishwasher into its niche Connection to water and drainage should be sited beside and not behind the dishwasher for accessibility. Connections are usually made in the area under the sink. Many kitchen unit manufacturers provide a cut-out in the base of the sink base unit for hoses to be fed through. -
Page 25: Dishwasher Height
Installing built-under "U" model dishwashers Dishwasher height The angle connector for the water drainage hose at the rear of the ^ Adjust the height of the dishwasher dishwasher can be turned. manuually before installing the ^ Turn the angle connector in the dishwasher. -
Page 26: Screw Feet
Installing built-under "U" model dishwashers Screw feet ^ Adjust the front screw feet manually ^ Use a TORX T20 screwdriver to or with a flat blade screwdriver. adjust the rear screw feet to the required height. Screw the feet out until the seal on the dishwasher is right up against Higher = turn clockwise the underside of the worktop, to... -
Page 27: Calculate The Decor Panel Height
Installing built-under "U" model dishwashers 3. Calculate the decor panel Before calculating the height of the decor panel you must first set the height dishwasher to its correct height (see The height of the dishwasher front step 2 "Building the dishwasher into its panel can be adjusted to match niche"). -
Page 28: Matching The Plinth Facing Of A Kitchen Run
Installing built-under "U" model dishwashers 4. Matching the plinth facing of Adapting the height of the decor panel supplied a kitchen run ^ Mark the measurement X on the left and right hand side of the decor panel and on the decor frame strips. ^ Take off and shorten the decor frame strips, the decor panel and the filler card (see Step 4). - Page 29 Installing built-under "U" model dishwashers ^ Bow the panel slightly, pull it out from ^ Loosen the screws a in the door under the control panel and take it outer panel, but do not unscrew off. completely. ^ Shorten the decor frame strips, and ^ Push the lower edge of the adapter plate b (corresponding to dimension the filler card (if used) by dimension...
- Page 30 Installing built-under "U" model dishwashers ^ Refit the filler card (if used) and the ^ Put back the left and right hand side decor panel. Fit the decor panel into decor strips and push them up over the lower decor frame strip, position the adapter plate from below.
-
Page 31: Securing The Dishwasher
Installing built-under "U" model dishwashers 5. Securing the dishwasher To ensure stability, the dishwasher must be fixed securely to the worktop. Two securing pieces are supplied with the dishwasher for this purpose. ^ Screw the countersunk screws (3.9 x 22) supplied upwards through the securing pieces on the left and right hand sides into the work surface to secure the dishwasher. -
Page 32: Adjusting The Door Springs
If the door front is too heavy for the door springs (i.e. the door falls open) then stronger springs should be fitted. Please contact your Miele dealer or the Miele Service Department for advice. ^ Adjust the door spring with a Torx T20 or a 1 x 5.5 mm screwdriver until... -
Page 33: Adjusting The Plinth Return
Installing built-under "U" model dishwashers 7. Adjusting the plinth return The plinth return on a "U" model dishwasher can be adjusted between 35 and 100 mm in 2.5 mm increments. ^ Push the spring clips on either side of the dishwasher outwards and push the brackets right in. - Page 34 Installing built-under "U" model dishwashers If you have pulled the plinth facing out too far you must not attempt to push it back in. It will have to be unscrewed and taken off. The spring clips can then be pushed outwards and the brackets pushed back in.
-
Page 35: Matching The Plinth Facing Of A Kitchen Run
Installing built-under "U" model dishwashers 8. Matching the plinth facing of ^ Using the front lower edge of the dishwasher door as a guide, draw a a kitchen run horizontal line across the plinth The plinth facing supplied will fit without facing. -
Page 36: Electrical Connection
All electrical work should be carried complete connection box and cable out only by a suitably qualified and by a Miele approved service competent person, in strict technician only. accordance with national and local safety regulations. - Page 37 Electrical connection The wires in the mains lead are coloured in accordance with the following code: Green/yellow = earth Blue = neutral Brown = live If the colours of the wires in the mains lead of this appliance do not correspond with the coloured markings identifying the terminals of your plug, proceed as follows:...
-
Page 38: Plumbing
Water "inlet" or "inlet / worktop, a special angle connector can drain" light (depending on model) be ordered from the Miele Spare Parts may light up, (see "Problem solving Dept. (Part No. 04 274 820). guide" in the Operating Instruction... -
Page 39: Drainage
Plumbing Drainage Venting the drainage system ^ Open the dishwasher door fully. – The machine drainage system is fitted with a non-return valve, which If the site drain connection is situated prevents dirty water from flowing lower than the guide path for the back into the machine via the drain bottom basket rollers in the open door hose. -
Page 40: Optional Accessories
... adjust the height of the dishwasher to ...a kit with extended machine feet between 87 cm and 92 cm (G 601 - G 632, G 636 - G 698, G 975) or between 89 cm and 94 cm (G 801 - G 832, G 836 - G 898) ...to match the facia panel of the dishwasher... -
Page 41: Technical Data
Technical data Dishwasher model G 601 - G 632 G 801 - G 832 Height Freestanding 84.7 cm (adjustable + 2.0 cm) Height built-in models 81.7 cm 83.7 cm (adjustable + 5.0 cm) (adjustable + 5.0 cm) Height of building in recess 82 cm (+ 5.0 cm) - Page 42 Technical data Dishwasher model G 636 - G 645, G 975 Height Freestanding 84.7 cm (adjustable + 4.0 cm) Height built-in models 81.7 cm (adjustable + 5.0 cm) Height of building in recess 82 cm (+ 5.0 cm) Width 59.8 cm Width of building in recess 60 cm Depth:...
- Page 43 Technical data Dishwasher model G 646 - G 657, G 692 G 846 - G 857, G 892 Height Freestanding 84.7 cm (adjustable + 4.0 cm) Height built-in models 81.7 cm 83.7 cm (adjustable + 5.0 cm) (adjustable + 5.0 cm) Height of building in recess 82 cm (+ 5.0 cm) 84 cm (+ 5.0 cm)
- Page 44 Technical data Dishwasher model G 681 - G 689 G 881 - G 889 G 693 - G 698 G 893 - G 898 Height Freestanding 84.7 cm (adjustable + 4.0 cm) Height built-in models 81.7 cm 83.7 cm (adjustable + 5.0 cm) (adjustable + 5.0 cm) Height of building in recess 82 cm (+ 5.0 cm)
- Page 48 Alteration rights reserved (NovoPlusB,P,S) / 1206 M.-Nr. 05 565 043 / 01 en - GB...