Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Bosch DX4010V2
Summary of Contents for Bosch DX4010V2
- Page 1 DX4010V2 Installation Instructions RS-232/USB Serial Interface Module...
- Page 2 DX4010V2 | Installation Instructions | Trademarks Trademarks • BlackBox® is either a registered trademark or a trademark of BlackBox Corporation in the United States and/or other countries. Bosch Security Systems, Inc. | 9/08 | F01U083036-01...
-
Page 3: Table Of Contents
Table 2: Diagnostic LED Functions ..... 6 Table 3: Option Bus Address DIP Switch Settings8 Table 4: SDI Bus Address DIP Switch Settings ... 9 Table 5: Alternate Wiring Configuration ..... 10 Bosch Security Systems, Inc. | 9/08 | F01U083036-01... -
Page 4: 1.0 General Information
BIS: Supported on SDI Bus control Option or SDI data bus. panels, v6.3 and higher (D9412GV2, The DX4010V2 is used to connect a PC with RPS, D7412GV2, D7212GV2, D9412G, BIS, PC 9000, CMS 7000, or other third party D7412G, and D7212G). -
Page 5: 4.0 Wiring
SDI option bus wiring is limited to 305 m (P6). (1000 ft). Figure 4: Serial Device Connections Connect the DX4010V2 to the control panel data and auxiliary power sources as shown in Figure 2. Rx Tx Figure 2: Control Panel Connections... -
Page 6: Dx4010V2 Jumper Pin Settings
DX4010V2 | Installation Instructions | 5.0 DX4010V2 Jumper Pin Settings Figure 5 shows a parallel printer connected to the serial output of the DX4010V2. This type of Figure 6: P2 Jumper Settings connection requires the use of a serial to parallel converter, such as the BlackBox PI045A serial to Centronics parallel converter cable. -
Page 7: Address Dip Switches
DX4010V2. Direct Connection Refer to Table 3 on page 8 for DIP switch option bus The DX4010V2 can be used to create a local direct address settings. connection for remote programming of a compatible Refer to Table 4 on page 9 for DIP switch SDI bus control panel. - Page 8 * Installer’s mode: Use for direct connection of remote programming and diagnostic tools. ** DS7412 emulation The DS7400Xi (USA) only supports one DX4010V2. Option bus control panels: D6412, D4412, DS7240, DS7220, DS7400Xi (v2.02 or higher). Bosch Security Systems, Inc. | 9/08 | F01U083036-01...
-
Page 9: Table 4: Sdi Bus Address Dip Switch Settings
* Used for BIS, PC 9000, and other third party applications. ** Used for RPS and alternate communication. SDI bus control panels (v6.0 or higher): D9412GV2, D7412GV2, D7212GV2, D9412G, D7412G, D7212G, D9124, D9112, D7412, and D7212. Bosch Security Systems, Inc. | 9/08 | F01U083036-01... -
Page 10: Db9 Dte Rs-232 Connector (P6)
DB9 DTE RS-232 Connector (P6) 7.0 DB9 DTE RS-232 Figure 8: DB9 Connector Layout Connector (P6) The DX4010V2 serial port is wired as a DTE device. • If the connected device is a data carrier equipment (DCE) device (most common, such... -
Page 11: Data Bus Connector (P3)
Installing USB Drivers Install the drivers. 1. Double-click CP210x_VCP_Win2K_XP_S2K3.exe. Figure 10: Select File 4. Click I accept the terms of the license agreement. Then click Next. Figure 13: Security Warning Bosch Security Systems, Inc. | 9/08 | F01U083036-01... -
Page 12: Figure 14: Destination Location
10. The program will look for the file location. Figure 19: Scanning 7. The drivers install. Figure 16: Setup Status 11. When the installation completes successfully, click OK. Figure 20: Installation Complete Bosch Security Systems, Inc. | 9/08 | F01U083036-01... -
Page 13: Figure 21: System Properties
Via drop down menu. 7. Enter the COM Port number from Step 5 in the Com Port field. 8. Make sure the DX4010V2 is connected to a USB Port, then click Connect. 9. The installation process is complete. Figure 23: Panel Communication... - Page 14 Bosch Security Systems, Inc. 130 Perinton Parkway Fairport, NY 14450-9199 (800) 289-0096 © 2008 Bosch Security Systems, Inc. F01U083036-01...