Honeywell Enviracaire Elite HE365B Installation Insrtuctions
Powered flow-through humidifier
Hide thumbs
Also See for Enviracaire Elite HE365B:
- Manual (13 pages) ,
- Owner's manual (9 pages) ,
- Installation instructions (2 pages)
Advertisement
Quick Links
Honeywell
envi
ra E,.
HE365A, B PoweredFlow-Through Humidifier
TRADELINE ®
READ AND SAVETHESEINSTRUCTIONS
"4
Ill
"O
I--
-I
131
APPLICATION
The Enviracaire Elite
TM
HE365A, B Powered Flow-Through
Humidifier
works with the warm air furnace blower to provide humidification for the
whole house. The HE365A,B works with virtually any Honeywell
humidity control, and can be integrated to the temperature control in
the home when controlled by the Honeywell Perfect Climate Comfort
Center
TM
control.
INSTALLATION
When Installingthis Product...
1. Read these instructions carefully. Failure to follow them could
damage the product or cause a hazardous condition.
2. Check the ratings given in the instructions and on the product to
make sure the product is suitable for your application.
3. Installer must be a trained, experienced
service technician.
4. After installation is complete, check out product operation as
//_provided
in these instructions.
CAUTION
/k
Hazardous Voltage.
Improper drilling can cause equipment damage or personal
injury.
Do not cut or drill into any air conditioning or electrical
accessory.
CAUTION
Freezing Water, Flooding or Static Pressure Hazard.
Can cause water damage or permanent equipment
damage.
•
Locate the humidifier where the ambient temperature
is
between 32°F (0°C) and 160°F (71 °C) or property damage
can occur.
•
Do not install humidifier where freezing temperatures
could
occur.
•
Be sure supply plenum static pressure is no greater than 0.4
in. wc and water pressure is no greater than 125 psi.
IMPORTANT
•
Mount
the humidifier
at least 3 in. (76 mm) above
the furnace
jacket
to allow adequate
space
for the drain line. Check
that
there is adequate
space above
the humidifier
to remove
and
instafi the humidifier
covet:
Do not instafi
on a furnace
jacket.
1. Determine the best location for the humidifier and draw a level
line on the plenum. See Fig. 1 and 2.
IMPORTANT
To assure
optimal
product
performance,
be sure
the template
is level before
marking.
2. Tape this piece of paper in position as your template and trace
around the template.
3. Remove the template and carefully cut the rectangular opening.
4. Loosen the thumbscrew
on the bottom of the humidifier and
remove the cover.
5. Remove the humidifier pad assembly by grasping the top of the
tray and pulling the assembly out of the housing. See Fig. 3.
6. Position the securing clips as shown in Fig. 4.
Fig. 1. Typical humidifier installation
locations.
/
x
//
\x
/
\
//
x\
(
h
MI28/2
Fig. 2. HE360 Humidifier location
in relation to air conditioning
cooling
coils.
FEED TUBE NOZZLE
WATER
HUMiDIFiER
THUMB
SOREW-x .
Fig. 3. Humidifier components.
HUMIDIFIER
HOUSING
IvH
MI2813
Fig. 4. Position
securing clips.
7. Position the humidifier housing in the hole (be sure it is level), so
the locking tabs are in place on the upper and lower sheet metal
edge of the hole.
8. Push in securing clips until completely seated.
9. Drill holes and install the three sheet metal screws at the top of
the humidifier housing. Secure the housing with the three
remaining screws.
10. Reinstall the humidifier pad assembly in the humidifier housing.
IMPORTANT
For proper
operation,
be sure
the mark
on the end of the
humidifier
pad is facing
up. Check that the water feed
tube is
placed
in the guide
slots of the humidifier
housing.
11. Hook the top of the cover to the housing and secure with the
thumbscrew located at the bottom of the cover.
WIRING
WARNING
Voltage Hazard.
Moving parts can cause electrical
shock and injury.
•
Disconnect power supply before installation or servicing.
•
This device contains a moving fan blade; do not operate the
humidifier without the cover securely attached.
All wiring must comply with applicable local codes, ordinances and
regulations.
For H808 Humidistat, H8908 or H908 Convertible Humidity
Control Wiring Connections:
IMPORTANT
•
Select models of fan centers include humidifer taps so the
current sensing relay or sail switch is not needed.
•
If not using a current sensing relay or sail switch, the 120V
humidifier plug must be energized during blower motor cycles
for proper operation.
1. Wire the current sensing relay or sail switch.
2. Connect only the two yellow wires to the humidistat (red wire
connections are not used for mechanical humidistats). See the
typical wiring diagrams in Fig. 5 through 7.
For additional mounting and wiring information, refer to the humidistat
installation instructions.
LLI
--I
rt
ILl
® U.S. Registered Trademark
Copyright © 2000 Honeywell
• All Rights Reserved
TEMPLATE
II I I I I I II IIII IIIII
69-1428
Advertisement
Related Manuals for Honeywell Enviracaire Elite HE365B
Summary of Contents for Honeywell Enviracaire Elite HE365B
- Page 1 The HE365A,B works with virtually any Honeywell humidity control, and can be integrated to the temperature control in the home when controlled by the Honeywell Perfect Climate Comfort MI2813 Center control.
- Page 2 WITH ONE MI2820B AND OVERLOAD PROTECTION AS REQUIRED. OR TWO TRANSFORMERS A24V WIRING. Fig. 8. Typical wiring diagram for humidifier using H1008AAutomatic Humidity Control. Honeywell Home and Building Control Home and Building Control Honeywell Honeywell Limited-Honeywell Limitde 1985 Douglas Drive North...