GE Monogram ZDP48N4G Installation Instructions Manual
48", 36", 30" professional ranges
Hide thumbs
Also See for Monogram ZDP48N4G:
- Owner's manual (46 pages) ,
- Installation instructions manual (16 pages) ,
- Use and care manual (36 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for GE Monogram ZDP48N4G
Summary of Contents for GE Monogram ZDP48N4G
- Page 1 Installation Instructions ProfessionalRanges 48" Natural Gas Models ZDP48N4G ZDP48N6R ZDP48N6D 48" LP Gas Models ZDP48L4G ZDP48L6R ZDP48L6D 36" Natural Gas Models ZDP36N6 ZDP36N4R ZDP36N4D 36" LP Gas Models ZDP36L6 ZDP36L4R ZDP36L4D 30" Natural Gas Model ZDP30N4 30" LP Gas Model ZDP30L4 Monogram._...
- Page 2 Installation Instructions BEFORE YOU BEGIN CAUTION: THESE RANGES SHOULD BE INSTALLED Read these instructions completely and IN CONJUNCTION WITH A SUITABLE carefully. OVERHEAD VENT HOOD. Due to the high heat capacity • IMPORTANT- save these instructions for of this unit, particular attention should be paid to the local inspector's use, hood and duct work installation to assure it meets local building codes.
-
Page 3: Table Of Contents
ZDP36N4R - 4 gas burners and grill installation situation. ZDP36N4D - 4 gas burners and griddle 48" Natural Gas Models: ZDP48N4G -4 gas burners, grill and griddle 36" Liquid Propane Gas Models: ZDP36L6 - 6 gas burners ZDP48N6R-6 gas burners and grill... -
Page 4: Product Dimensions And Clearances
Design Information PRODUCT DIMENSIONS AND CLEARANCES 48"Wide RangeModels 36"Wide RangeModels _:::::::::::::±_:::::::::::::::::_:_:_:::_:_ 22 _ 35-1/4"-36-3/4" < 28-1/4'_ _35-7/8" 48"and 36"RangeModels 12"Min. to Combustibles or l/' 9 1/2"_ 29-1/16''_ 0" Min. to Combustibles -3/4"_ ",_ with 12" or 22" Backsplash 36" Min. 22"... - Page 5 Design Information PRODUCT DIMENSIONS AND CLEARANCES 30"Wide RangeModels 9-1/2" 27-3/8"_ 22" 3/4"_ _--22" High 36" Min. Backsplash to Combustibles with Shelf Backsplash [_29-1/4"_ 43-7/8" NOTE: Refer to Vent Hood Installation Instructions for hood height above the range. 1-1/2" Electrical S upply GasSupply [ ....
-
Page 6: Advance Planning
Design Information ADVANCE PLANNING TOOLS REQUIRED Refer to "Dimensions and Clearances" for appropriate • Saw placement and necessary clearances when planning • Measuring tape the installation. • Carpenter's square • Cabinetry can not be installed directly above the • Pipe wrench range. -
Page 7: Power Supply Locations
Installation Preparation POWER SUPPLY LOCATIONS If the electrical service provided does not meet the above specifications, it is recommended that a Gas Supply: licensed electrician install an approved outlet, • The natural gas models are designed to operate at 5" •... -
Page 8: Step 1, Remove Packaging
Installation STEP 1 REMOVE PACKAGING Slot Before moving the range indoors: • Remove outer carton and packing material from the shipping base, PulI the hinge locks down to unlock. Remove oven doors: • Fully open the door. • Each hinge has a hinge lock, Close the hinge latch down against the door frame. -
Page 9: Step 2 Level The Range
Installation STEP 2 LEVEL THE RANGE NOTE: Rear range leveling legs are not accessible after • Adjust the height of the range to countertop height installation. or higher. • Check to be sure the adjoining cabinets/countertops IMPORTANT: The range should always be installed are level, front to back and left to right across the at countertop height or higher. -
Page 10: Step 3, Install Anti-Tip Device
Installation STEP 3 INSTALL ANTI-TIP DEVICE (CONTINUED) (2) WoodScrewsinto SmallHoleForWood BackWall Installations(2 Total) (All Installations) (2) LargeHolesFor ConcreteInstallations Back SmallHolesForWood Wall Installations(2 Wood Slide Strip Dimension A 1/4" 5/8" ZDP36 ZDP30 Wood Construction: Concrete or Cement Construction: • Place the bracket against the back wall, into the right Hardware Required (not supplied): rear corner of the installation location. -
Page 11: Step 4 Connect Range To Gas
Installation STEP 4 CONNECT RANGE TO GAS Assure that gas supply is turned off at the shut-off valve: _k_ CAUTION: Do not use a flame to check for gas leaks. • Connect flexible metal connector to incoming gas line pipe stub located on the left side on the bottom back MISE EN GARDE : of the range. -
Page 12: Step 5 Connect Electrical
Installation STEP 5 CONNECT ELECTRICAL STEP 7 REPLACE OVEN DOOR(S) Plug power cord into properly grounded receptacle, IMPORTANT: Do not lift the door by the handle. To replace the oven doors: • Firmly grasp the door at the top sides. This is critical. STEP 6 SLIDE RANGE INTO •... -
Page 13: Step 8 Assemble And Adjust Burners
Installation STEP 8 ASSEMBLE AND ADJUST BURNERS Assemble burners as shown. Checkto be sure that burner heads and caps are securely seated. Pin(s) must completely engage holes to ensure proper assembly. Burner Cap BurnerHead ._ • Check for proper ignition: - Push in one control knob and turn 90°... -
Page 14: Finalize Installation
Installation FINALIZE INSTALLATION Place the burner grates over the burners. Press corner The griddle has two leveling screws beneath the rear of the grate to the cooktop. The grates should be seated flue cover that can be used to adjust to the desired slope. and should not rock. - Page 15 Installation INSTALL 9" or 12" HIGH BACKSPLASH Slotsfor Vertical \ Adjustment • Install and level the range or cooktop according to the Backsection installation instructions, • Remove the backsplash packaging, Select the back, wall mount panel with mounting screw slots. l/B'L •...
- Page 16 F<>r M onog'ra_? '_local s_r_Jice h_ )our arm, call l._S00. 444. l,_4 _. NOTE:] ro(hi(:l iml)l-o'_(m( i'_ a (:olHilitling (_ll(l(_a'_'()r sl)(_(if](:alions m-(_ sul;_j(:(t to (:hmig( Wil[lotlr noti(:(. Monogram: Pub.No.49-80222-1 PartNo. 164D4290P374 GE Consumer & Industrial 17681Rev.B Louisville, KY4ll225 12-04JR ©2004 GE Company...