Advertisement
Quick Links
SHARP
iNSTALLATiON
iNSTRUCTiONS
BUILT-IN KiT MODEL
RK-12S30
iMPORTANT:
PROVIDED
EXHAUST DUCT
BACK
DIVIDE PLATE L
EXHAUST DUCT BOTTOM
This Built-In Kit is designed
for use with Sharp SuperSteam
Ovens specifying
a RK-12S30
Built-In Kit on the rating label on the front of the oven.
The cabinet or wall opening
must be within the following
dimensions:
HEIGHT
19" to 19 1/8" (482 mm - 486 mm)
WIDTH
28" to 28
1/4"
(710 mm - 719 mm)
DEPTH
23
1/4"
minimum
(509.5 mm minimum)
The completed
built-in
kit frame assembly dimensions:
HEIGHT
19
1/2"
(495mm)
WIDTH
30" (762mm)
NOTE:The bottom ofthe cut-out opening for built-in usemust be 36 inches (915 mm) or higher from the floor.
PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION!
The electrical
requirements
for this oven are 120 volts, 15 amps. The oven has a 5-15 plug
and requires a 5-15 receptacle.
PARTS
PART NAME
Q'TY
DUCT UPPER
RECTIFIER
PLATE L
DIVIDE PLATE R
EXHAUST
DUCT LEFT
FRAME
REAR SPACER
ASSEMBLY
SCREW@ - SHORT
J
EXHAUST
DUCT
RIGHT
SCREW(B) - MIDDLE
SCREW (C) - LONG
* For walls other than wood, you may need screws appropriate
for that
wall to install the frame.
* Be sure to DISCONNECT THE PLUG of the oven from the electrical
outlet before installing
the oven and kit.
* Because the kits are metal, due caution should
be used in handling
and installation
to avoid the possibility
of injury.
EXHAUST DUCT BACK
1
PDVC-B 107WRWZ
EXHAUST DUCT UPPER
1
PDVC-B 105WRWZ
DIVIDE PLATE L
1
PSKR-A486WRWZ
DIVIDE PLATE R
1
PSKR-A487WRWZ
RECTIFIER PLATE L
1
PSKR-A484WRWZ
EXHAUST DUCT LEFT
1
PDVC-B 108WRWZ
EXHAUST DUCT RIGHT
1
PDUC-B117WRWZ
EXHAUST DUCT BOTTOM
1
PDVC-B 106WRWZ
FRAME ASSEMBLY
1
FDEC-A004WRKZ
SCREW(A)
23
XHTS740P08000
SCREW(B)
2
XMMS841P13000
SCREW(C)
4
XMSS827P25000
REAR SPACER
1
PSPAFA003WRWZ
CUSHION _ 5/8" x 16",
15 mm x 405 mm
2
PCUS-A245WRPZ
CUSHION _2)
1/4" X
24 3/8",
5 mm x 618 mm
1
PCUS-A247WRPZ
CUSHION C3)1 1/8" x 27 1/8",
30 mm x 689 mm
1
PCUS-A249WRPZ
CUSHION _4_
1/4" X
12",
5 mm x 305 mm
1
PCUS-A251WRPZ
CUSHION @
1/4" X
15",
5 mm x 382 mm
1
PCUS-A253WRPZ
TI NSEB 184WR RZ-D92
Printed in Thailand
Advertisement
Related Manuals for Sharp RK-12S30
Summary of Contents for Sharp RK-12S30
- Page 1 RK-12S30 BUILT-IN KiT MODEL iMPORTANT: This Built-In Kit is designed for use with Sharp SuperSteam Ovens specifying a RK-12S30 Built-In Kit on the rating label on the front of the oven. The cabinet or wall opening must be within the following...
- Page 2 PREPARATION Follow the directions from 1 to 5 to attach cushions to some parts. 1. EXHAUST DUCT UPPER Remove the backing paper from each CUSHION _. Attach the CUSHIONS _ to each side flange of the EXHAUST DUCT UPPER as shown in the illustration below.
- Page 3 3. EXHAUST DUCT BOTTOM Remove the backing paper from CUSHION @. Attach the CUSHION @ to the EXHAUST DUCT BOTTOM as shown in the Illustration below. * Start A to attach the CUSHION @. EXHAUST DUCT BOTTOM 4. DiViDE PLATE L Remove the backing paper from CUSHION _.
-
Page 4: Step 2: Installation
STEP 1" CABINET OR WALL OPENING Provide an opening in the wall or cabinet shown in Figure 1. The depth should minimum 23 1/4" (590.5 mm). The floor of the opening should be constructed plywood strong enough to support the weight of the oven (about 150 Ibs., 68.1 kg) and should be level for proper operation of the oven. - Page 5 STEP 3: EXHAUST DUCT BOTTOM iNSTALLATiON _0 Place the oven onto the EXHAUST DUCT BOTTOM, lowering the 4 feet of the oven onto the projections at the 4 corners of EXHAUST DUCT BOTTOM as shown in Figure 3-A. EXHAUST DUCT BOTTOM Figure 3-A Figure...
- Page 6 STEP 5: iNSTALLATiON OF REAR SPACER and EXHAUST DUCT UPPER _0Attach RECTIFIER PLATE L to inside of EXHAUST DUCT UPPER with 4 SCREWS (A) as shown in Figure 5-A. @Place EXHAUST DUCT UPPER over the oven and EXHAUST DUCT BACK, and attach REAR SPACER with 2 SCREWS (A) in Figure 5-B.
- Page 7 STEP 7: iNSTALLATiON OF EXHAUST DUCT RIGHT Attach EXHAUST DUCT RIGHT to the right wall of the oven. Tighten with 4 SCREWS (A) as shown in the Figure 7, EXHAUST DUCT UPPER SCREW (A) DUCT RIGHT SCREW (A) Figure 7 DIVIDE PLATE R STEP 8: OVEN iNSTALLATiON...
-
Page 8: Assembly & Installation
Pull bottom panel of FRAME ASSEMBLY toward you to remove or replace the drip tray. For any other assistance or information about this product, please call SHARP's Customer Assistance Cen- ter 1-800-BE-SHARR ® SHARP ELECTRONICSCORPORATION Sharp Plaza, IVlahwah, N J 07495-1163...