Advertisement
Table of Contents
- 1 Pre-Installation Requirements
- 2 Electrical Requirements
- 3 Water Supply Requirements
- 4 Drain Requirements
- 5 Exhaust System Requirements
- 6 Gas Supply Requirements
- 7 Mobile Home Installation
- 8 Location
- 9 Rough-In Dimensions
- 10 Unpacking
- 11 Electrical Installation
- 12 Grounding Requirements
- 13 Replacement Parts
- Download this manual
Installation
Instructions
Full Size Laundry Center
Gas & Electric
Before beginning
installation,
carefully read these instructions.
This will simplify the installation
and ensure the laundry center is installed correctly and safely. Leave these instructions
near the
laundry center after installation
for future
reference.
NOTE:
The electrical service to the laundry center must conform with local codes and ordinances
and the latest edition
of the National
Electrical Code, ANSI/NFPA 70, or in Canada, the Canadian
Electrical Code, CSA C22.1
NOTE:
The gas service to the laundry center must conform
with local codes and ordinances
and
the latest edition of the National
Fuel Gas Code ANSI Z223.1/NFPA
54, or in Canada, the Canadian
Natural
Gas and Propane Installation
Code, CSA B149. 1.
NOTE:
The laundry
center
is designed
under
ANSI Z21.5.1
or ANSI/UL
2158- CAN/CSA
C22.2
(latest
edition)
for HOME
USE only. This laundry
center
is not recommended
for commercial
applications
such as restaurants
or beauty salons, etc.
For your safety the information
in
this manual must be followed
to minimize the risk
of fire or explosion or to prevent property damage,
personal injury or loss of life.
- Do not store or use gasoline or other flammable
vapors and liquid in the vicinity of this or any
other appliance.
- WHAT TO DO IF YOU SMELL GAS
e Do not try to light any appliance.
t
Do not touch any electrical switch; do not use
any phone in your building.
e Clear the room, building or area of all
occupants.
e Immediately
call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
e If you cannot reach your gas supplier, call the
fire department.
Installation and service must be preformed
by a
qualified installer, service agency or the gas
supplier.
Contents
SUBJECT
PAGE
Pre-lnstallation Requirements
Electrical Requirements
Water Supply Requirements
Drain Requirements
Exhaust System Requirements
Gas Supply Requirements
Location
Mobile Home Installation
Rough-In Dimensions
Unpacking
Electrical Installation
Grounding Requirements
3 & 4-Wire Connections
Installation
Replacement Parts
2
2
2
2
3
4
4
4
5
5
6
6
7
7
8
Printed in U,S,A.
P/N131661700 (O11O)
Advertisement
Table of Contents
Related Manuals for Frigidaire FLEB43RGS0
Summary of Contents for Frigidaire FLEB43RGS0
- Page 1 Installation Instructions Full Size Laundry Center Gas & Electric Before beginning installation, carefully read these instructions. This will simplify the installation and ensure the laundry center is installed correctly and safely. Leave these instructions near the laundry center after installation for future reference.
-
Page 2: Pre-Installation Requirements
POWER SUPPLY CORD -The gas laundry center is equipped PRE-INSTALLATION REQUIREMENTS with a 120 volt 3-wire power cord. Tools and Materials Required for Installation: 1. Phillips head screwdriver. 2. Channel-lock adjustable pliers. NOTE: Do not under 3. Carpenter's level. any circumstances 4. -
Page 3: Exhaust System Requirements
EXHAUST SYSTEM REQUIREMENTS The maximum length ofthe exhaust system depends upon Use only 4 inch (10.16 cm) diameter (minimum) rigid or flexible the type of duct used, number of elbows and type of exhaust metal duct and approved vent hood which has a swing-out hood,... -
Page 4: Gas Supply Requirements
GAS SUPPLY REQUIREMENTS 5, The following illustrations show minimum clearance dimensions and air openings for proper operation in a recess 1. Installation MUST conform with local codes, or in the or closet installation. absence of local codes, with the National Fuel Gas Code, ANSI Z223.1 (latest edition) or in Canada, the current AN/CGA B149. -
Page 5: Rough-In Dimensions
ROUGH-IN DIMENSIONS 2YzlN (6 35 CM) GASSUPPLY PiPE (REAR) 1 7/8 iN It-- (476 CM) _1333 75 Y_ IN 5Y41N (19177 CM) ELECTRICAL CONNECTION 43 IN 54 5/16 IN WATER iNLETS 4 13/16 iN (13795 CM) (REAR) (12 22 CM) 43 IN (1O922 eM) 361/16iN... -
Page 6: Electrical Installation
ELECTRICAL INSTALLATION For a permanently connected laundry center: ALL ELECTRICLaundry Centers The laundry center MUST be connected to a grounded metal, permanent wiring system; oran equipment grounding conductor MUST be run with the circuit conductors and connected to the he following are specific requirements equipment-grounding terminal or lead on the appliance, fe electrical installation of your laundry... - Page 7 ELECTRICAL CONNECTIONS 6, Attach the white (neutral) wire from the power cord and the FOR A 3-WIRE SYSTEM green ground wire from the appliance harness to the silver- colored center terminal on the terminal block. Tighten the screw securely. ELECTRIC Laundry Center Green Ground Screw 1, Remove the screw securing the...
-
Page 8: Replacement Parts
7,GAS CONNECTION 10. Connect the exhaust duct to outside duct work, Use duct (Gas laundry centers only) a. Remove the shipping cap from gas pipe at the rear of the tape to seal all joints, dryer, 11. Plug the power cord into a grounded outlet, NOTE: DO NOT connect the laundry center to LR gas service NOTE: Check to ensure the power is off at a circuit breaker/ without converting the gas valve.