COLOR TELEVISION RECEIVER Chassis : K54A(P) Model : TSL3099WF/XAA COLOR TELEVISION RECEIVER CONTENTS Precautions Reference Information Specifications Alignment and Adjustments Troubleshooting Exploded Views and Parts List Electrical Parts List Block Diagrams Schematic Diagrams...
Heed the high voltage limits. These include not exceed 0.5 milliamp. Reverse the power- the X–ray Protection Specifications Label, and plug prongs in the AC outlet and repeat the the Product Safety and X-ray Warning Note on test. the service data schematic. Samsung Electronics...
Page 3
14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheating, and correct any potential hazards. Samsung Electronics...
Make sure that the portion around 8. Always connect a test instrument’s ground the serviced part has not been damaged. lead to the instrument chassis ground before connecting the positive lead; always remove the instrument’s ground lead last. Samsung Electronics...
Page 5
4. Do not use freon-propelled chemicals. These unpackaged replacement ESDs. Motions such can generate electrical charges that damage as brushing clothes together, or lifting a foot ESDs. from a carpeted floor can generate enough static electricity to damage an ESD. Samsung Electronics...
Milliliter Hertz Millimeter Hour Millisecond Inches Per Second Millivolt Kilowatt-hour Nanofarad Kilogram Kilohertz Picofarad Kilohm Pound Kilometer Revolutions Per Minute km/h Kilometer Per Hour Revolutions Per Second Kilovolt Second (Time) Kilovolt-ampere Volt Kilowatt Volt-ampere Liter Watt Megahertz Watt-hour Samsung Electronics...
Page 7
Fail Safe Voltage Controlled Oscillator Ground VCXO Voltage Controlled Crystal Oscillator Green-Y Very High Frequency High Video Intermediate Frequency High-Frequency Variable Resistor HI-FI High Fidelity Video Tape Recorder Inductance-Capacitance VTVM Vacuum Tube Voltmeter Integrated Circuit Transistor Intermediate Frequency Samsung Electronics...
DC 1.5V (AAA Size) x 2 Power Consumption 220 W Rectification Insulation Switch Sound Output 7.5 W x 2, WOOFER: 22WX1 Transmitter Adjustment: Infrared Rays Type Adjustment System UHF/VHF electronic tuner fine tuning: Electronic Type Electronic Function Adjustment Specifications are subject to change. Samsung Electronics...
5. Turn the Static Focus VR counterclockwise slowly for the clearest NO USE center vertical line. <FBT FOCUS PACK> After Adjustment 6. Turn the Dynamic Focus VR clockwise slowly for the clearest third line. 7. Check for the FOCUS of entire screen. If necessary, re-do adjustments 3~6. Samsung Electronics...
Page 13
3. Use the Volume +/- buttons to select SBT. 4. Press the Menu or Mute button on the remote control to adjust so that the seventh step on the right of screen cannot be seen. 5. Press the Memory button to exit. Samsung Electronics...
Page 14
5V), and then its difference voltage will be amplified. Its value will be convert PWM in HVIC02, and then PWM pulse will be output from HVIC02 pin #9, #10. Transistor HVQ01 is used as Buffer for impedance matching. Samsung Electronics...
Page 15
Its value will be inputed HVIC02 PIN #4(X-ray detect), and high voltage oscillation will be OFF in order to protect X-ray. In this case, high voltage will be On if power is re-ON. + 12V HVC03 HVR01 HVQ02 HVR13 F/S DETECTOR HVR08 HVC02 HVIC03(L431) HVD01 HVIC02 TS14 X-ray HVR25 HVDZ02 Samsung Electronics...
Page 17
RED SIGNAL OF OSD V1(R) OSD R BLANK BLANKING SIGNAL OF OSD HSYNC HSYNC HORIZONTAL SYNC INPUT FOR OSD VSYNC VSYNC VERTICAL SYNC INPUT FOR OSD P12/I2CMD2 SDA1 I2C BUS DATA 1 P11/I2CMC2 SCL1 I2C BUS CLK 1 E2PROM WRITE PROTECT Samsung Electronics...
Page 18
SOUND RESET PWM1 S-RESET PWM2 TILT TILT CONTROL PWM3 MUTE SOUND AMP MUTE SOUND AMP MUTE PWM4 D-COIL DEGAUSSING COIL CONTROL OUTPUT PWM5 LED1 STAND BY LED TIMER LED PWM6 PWM6 LED2 P10/R(0) P08/R(1) P18/G(0) HOLD P13/G(1) P14/B(0) P15/B(1) Samsung Electronics...
1. When IC902 (EEPROM) is replaced, warm up the TV for 4~5 seconds after plugging in. 2. After IC902 (EEPROM) is replaced, enter the Service Mode and standard data for all items. 3. Make the following adjustments: Geometric, White Balance, Sub-contrast, PIP contrast, Sub-brightness Samsung Electronics...
Page 20
1 : PC OFF 0 : ACS ON 1 : ACS OFF 0 : X-RAY ON 1 : X-RAY OFF DON'T CARE DON'T CARE DON'T CARE DON'T CARE DON'T CARE DON'T CARE DON'T CARE DON'T CARE DON'T CARE DON'T CARE Samsung Electronics...
Adjusts the horizontal variance (depending on the high pressure) H Shift Horizontal Shift V Angle Adjusts so that the vertical line becomes rectangular V Bow Adjusts so that the vertical lines are symmetrical H Sync Phase Adjusts the horizontal sync phase Samsung Electronics 4-11...
Page 23
Alignment and Adjustments 4-8 Screen Change (I2C Bus Geometric Adjustment) V - SHIFT V - Amp 7 V S C V-S-CORR (VSC) H E W H Trapizium Parabola H Symmetry H Corner 10 H SHIFT 4-12 Samsung Electronics...
VERTICAL AMP °í ¾ Ð DRIVE TR PCF8591 INPUT IRFS640A LA7845 DVDÀ Ô · Â IDENENT Y,Pb,Pr H DRIVE °í ¾ Ð X-LAY H-OUT POINT DOUBLE R434 ¾ ç ´ Ü 2SC5446 FOCUS AC INPUT POWER TRANS F6656 Samsung Electronics...
Page 48
Block Diagrams 8-3 POWER BLOCK Samsung Electronics...