Related Manuals for Husqvarna K1250 ACTIVE
Summary of Contents for Husqvarna K1250 ACTIVE
-
Page 1: K1250 Active
K1250 ACTIVE Operator’s manual Read these instructions carefully and make sure you understand them before using the machine. -
Page 2: Symbol Explanation
SYMBOL EXPLANATION Symbols on the power cutter: Symbols in the Operator's Manual: WARNING! The power cutter can be Switch off the engine by moving the stop dangerous! Careless and incorrect use can switch to the STOP position before result in serious or fatal injury to the carrying out any checks or maintenance. -
Page 3: Table Of Contents
Fuel filter ................18 Air filter ................18 Starter ................19 Spark plug ................. 20 Muffler ................20 Cooling system ..............20 Daily maintenance ............. 21 Weekly maintenance ............21 Monthly maintenance ............21 Technical Data K1250 Active ..............22 English –... -
Page 4: Safety Instructions
SAFETY INSTRUCTIONS THE POWER CUTTER’S SAFETY WARNING! Incorrect or careless use of a EQUIPMENT power cutter can turn it into a dangerous tool that can cause serious or even fatal injury. It This section describes the power cutter’s safety equipment, its is extremely important that you read and function and how checks and maintenance are carried out to understand this manual. -
Page 5: Stop Switch
SAFETY INSTRUCTIONS 3 Muffler Control, maintenance and service of the machine‘s safety equipment WARNING! During use and for some time after the muffler is very hot. Do not touch the WARNING! All service and repairs to the muffler if it is hot! power cutter require special training. -
Page 6: General Safety Instructions
SAFETY INSTRUCTIONS 3 Muffler GENERAL SAFETY INSTRUCTIONS Never use a machine that IMPORTANT INFORMATION! has a defective muffler. Do not use the power cutter until you have read the entire contents of this Operator’s Manual. All servicing, in addition to the points listed in the section ”... -
Page 7: Fuel Safety
SAFETY INSTRUCTIONS GENERAL WORKING INSTRUCTIONS Fuel safety This section takes up the basic safety precautions for working (Filling/Fuel mixture/Storage) with the power cutter. Follow these general working instructions, but never use a machine without the possibility of calling for WARNING! Exercise great care when handling help in the event of an accident. -
Page 8: Kickback
SAFETY INSTRUCTIONS Water cooling Over exposure to vibrations can result in blood-vessel or nerve injury to persons WARNING! Water cooling, which is only used suffering with blood circulation problems. for petrol-driven power cutters and when Seek medical attention if you experience cutting concrete, cools the cutting blade and physical symptoms that can be related to over increases its service life as well as reduce... -
Page 9: Care And Storage
SAFETY INSTRUCTIONS Pull in Care and storage Pull in occurs when the lower part of the blade is suddenly stopped or when the cut closes. (To avoid this see the section General ” How to avoid kickback ” and ”Pinching/rotation” below). Partner’s power cutters are robust and durable. -
Page 10: Cutting Blades
SAFETY INSTRUCTIONS Abrasive blades CUTTING BLADES The cutting material in an abrasive blade consists of abrasive corn that is held together by an organic bonding agent. ”Reinforced blades” are made up of a fabric or fibre base that prevents total breakage at maximum working speed if the blade should be cracked or damaged. -
Page 11: Diamond Blades
SAFETY INSTRUCTIONS Guard Cutting blades Check that the guard is not cracked or shows signs of any Type of cutting blades other damage. Clean the Check that the blade is inside of the guard before approved for the same or fitting a new blade. -
Page 12: What Is What
WHAT IS WHAT? 16 3 What is what on a power cutter? Cylinder cover 12. Throttle control Muffler 13. Combination spanner Fuel tank 14. Air filter cover Starter throttle catch 15. Blade guard Choke 16. Starter handle Throttle trigger lockout 17. -
Page 13: Assembly
ASSEMBLY Fitting the cutting head Fitting the cutting blade Partner cutting blades are manufactured and approved Remove the bolts (1). Remove for freehand cutting. The the cover. Fit the drive belt paper labels on each side of over the clutch drum. Refit the the blade are there to cover and tighten the bolts. -
Page 14: Fuel Handling
FUEL HANDLING Fuelling IMPORTANT! The power cutter is equipped with a two-stroke engine and must always been run using a mixture of petrol and WARNING!The following precautions reduce two-stroke engine oil. It is important to accurately measure the the risk of fire: amount of oil to be mixed to ensure that the correct mixture is obtained. -
Page 15: Start And Stop
START AND STOP Start and stop Start WARNING! Before starting observe the WARNING! The cutting blade can rotate when following: the engine starts. Make sure it can rotate freely. • Do not start the power cutter without the Take hold of the front handle cutting arm or cutting head fitted. -
Page 16: Maintenance
MAINTENANCE Adjusting the drive belt Belt pulley and clutch Never start hte engine when the belt pulley and clutch are • The drive belt is fully removed for maintenance. enclosed and well protected from dust, dirt and mechanical effects during the cutting process. -
Page 17: Carburettor
MAINTENANCE Carburettor Carburettor Final setting of the idling speed T Adjust the idling speed with the screw T. If it is necessary to re- Your Partner product has been designed and manufactured to adjust, first turn the idle speed adjusting screw T clockwise, until specifications that reduce harmful emissions. -
Page 18: Fuel Filter
MAINTENANCE Fuel filter • The fuel filter sits inside the fuel tank. • The fuel tank must be protected from contamination when filling. This reduces the risk of operating disturbances caused by blockage of the fuel filter. • The filter cannot be cleaned but must be replaced with a new filter when it blocked. -
Page 19: Starter
MAINTENANCE Starter Tensioning the recoil spring WARNING! • Lift up the starter cord from • The recoil spring sits in its tensioned posi the cut out on the pulley and tion in the starter housing and can with turn the pulley approx. 2 careless handling fly out and cause personal turns clockwise. -
Page 20: Spark Plug
MAINTENANCE Ignition system Cooling system To maintain as low an operating temperature as possible the power cutter is equipped with a cooling system. IMPORTANT INFORMATION! This power cutter has a green coloured ignition system The cooling system consists of: with integrated speed governor (order no. 506 02 73-04). The machine may only be used with such a green 1. -
Page 21: Daily Maintenance
MAINTENANCE Below follows some general maintenance instructions. If you need further information please contact your service workshop. Daily maintenance 1. Check that throttle components work correctly from a safety view point (throttle and starter throttle catch). 2. Clean the main filter. 3. -
Page 22: Technical Data
We, Partner Industrial Products, S-433 81 Partille, Sweden, tel. +46-31-949000, declare under sole responsibility that the power cutter Partner K1250 Active from the serial numbers of 1998 and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), is in conformity with the following standards or other normative documents following the provisions in the COUNCIL’S DIRECTIVES:... - Page 23 English –...
- Page 24 108 88 01-26 ´*xp,¶6n¨ 2000W37...