DELL E152FPc SERVICE MANUAL 15” LCD MONITOR DELL E152FPc THESE DOCUMENTS ARE FOR REPAIR SERVICE INFORMATION ONLY. EVERY REASONABLE EFFORT HAS BEEN MADE TO ENSURE THE ACCURACY OF THIS MANUAL; WE CANNOT GUARANTEE THE ACCURACY OF THIS INFORMATION AFTER THE DATE OF PUBLICATION AND DISCLAIMS RE LIABILITY FOR CHANGES, ERRORS OR OMISSIONS.
DELL E152FPc Table of Contents TABLE OF CONTENTS....................... 2 1. MONITOR SPECIFICATIONS ....................4 2. LCD MONITOR DESCRIPTION ....................5 3. OPERATING INSTRUCTIONS ....................6 3.1 GENERAL INSTRUCTIONS....................6 3.2 CONTROL BUTTONS ......................6 3.3 ADJUSTING THE PICTURE....................7 4. INPUT/OUTPUT SPECIFICATION ..................10 4.1 INPUT SIGNAL CONNECTOR..................
Page 3
DELL E152FPc Revision List Revision Date Revision History TPV model Mar-20-2005 Initial Release Add” Max Brightness measurement” on April-25-2006 Page36...
DELL E152FPc 1. MONITOR SPECIFICATIONS Driving system TFT Color LCD Size 38.1mm(15.0") Pixel pitch 0.297mm(H) x 0.297mm(V) Flat Panel Viewable angle 120˚ (H) 100˚ (V) Response time (typ.) 25 ms Video Analog Only Sync. Type H/V TTL Separate and Composite Sync.
DELL E152FPc 2. LCD MONITOR DESCRIPTION The LCD MONITOR will contain a main board, an internal PWPC board, keypad board, which house the flat panel control logic, brightness control logic and DDC.The internal PWPC board will drive the backlight of panel and the DC-DC conversion.
DELL E152FPc 3. OPERATING INSTRUCTIONS 3.1 GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor. By changing these settings, the picture can be adjusted to your personal preferences.
DELL E152FPc 3.3 ADJUSTING THE PICTURE To set the OSD menu, perform the following steps: Briefly press the SELCT / MENU button to activate the OSD menu. The main menu appears on the screen with icons for the setting functions.
Page 8
DELL E152FPc Adjusting the brightness and contrast Calling the Brightness / Contrast setting window using Brightness button. Brightness Setting the brightness of the display With this function you change the brightness of the background lighting. Contrast Setting the contrast of the display With this function you modify the contrast of bright colour tones.
Page 9
DELL E152FPc Vertical Setting the vertical position of the OSD menu Position With this function you move the OSD menu up or down. Setting the display duration of the OSD menu, the default value is 20s; Hold Time With this function you select a value from 0 to 60 seconds.
DELL E152FPc 4.3 POWER SUPPLY REQUIREMENTS 4.3.1 INPUT REQUIREMENTS AC INPUT VOLTAGE: 100V ~ 240V AC INPUT FREQUENCY: 50 ~ 60 HZ AC INPUT CURRENT: 1.5A MAX INRUSH CURRENT: 50A MAX AT 220V LEAKAGE CURRENT: 3.5 mA Max. 4.3.2 OUTPUT REQUIREMENTS ITEM MIN.
Page 16
DELL E152FPc 1) MCU Initializes. 2) Is the EEprom blank? 3) Program the EEprom by default values. 4) Get the PWM value of brightness from EEprom. 5) Is the power key pressed? 6) Clear all global flags. 7) Are the AUTO and SELECT keys pressed? 8) Enter factory mode.
DELL E152FPc 7.3 KEYPAD BOARD 8. MAINTAINABILITY 8.1 EQUIPMENTS AND TOOLS REQUIREMENT Voltage meter. Oscilloscope. Pattern Generator. DDC Tool with a IBM Compatible Computer. Alignment Tool. LCD Color Analyzer. Service Manual. User Manual.
DELL E152FPc 8.2 TROUBLE SHOOTING 8.2.1 MAIN BOARD 1.NO SCREEN APPEAR Check Power board, is there DC level output? Check Correspondent component. Measured U402 pin 3 = 5 V? No DC Level Is there any shortage or cold solder? Measured U402 pin 2= 3.3V? Measured U401pin 2 =1.8V?
Page 29
DELL E152FPc 2.PANEL-POWER CIRCUIT Check the PPWR panel power relative circuit, Check FB401 should have response from 0V to 3.3V Q300, Q303 In normal operation, when LED =green, When we switch the power switch from on to off R308 should =0 v,...
Page 30
DELL E152FPc 4.U200-DATA OUTPUT Measured DVS, DHS (pin 8,9 from U200) Is the waveform ok? DCLK around 48 MHZ, DVS=60.09Hz, DHS around 31 KHz? (Refer to input NG, no transition signal=640x480@60 Hz 31k, and LED is Green) Replace GMZan3 (U200) or replace MAINBOARD.
Page 31
DELL E152FPc 8.2.2 PWPC BOARD 1.) No power Check to CN102 Pin10 = 5V Check Interface board Check AC line volt 120V or 220V Change F901 Check the voltage of C904(+) Check bridge rectified circuit Check start voltage for the pin3 of IC901...
Page 32
DELL E152FPc 2.) W / LED, No Backlight Check C201 (+) =12V Change F201 Check D201/Q206/Q207 Check ON/OFF signal Check Interface board Check U201 pin9=12V Change Q201 or Q202 Check the pin1 of U201 have saw tooth wave Change U201 Check D201 (-) have the output of square wave at short time.
Page 33
DELL E152FPc 8.2.3 Keypad Board OSD is unstable or not working Connect Keypad Board Is Keypad Board connecting normally? Replace Button Switch Is Button Switch normally? Replace Keypad Board Is Keypad Board Normally? Check Main Board...
DELL E152FPc 9.WHITE-BALANCE, LUMINANCE ADJUSTMENT Before started adjust white balance, please setting the Chroma-7120 MEM. Channel 3 to 6500 K colors, MEM. Channel 4 to 9300 K colors, MEM. Channel 9 to 5700 K (our 9300 parameter is x = 283 ±28, y = 297 ±28, Y = 175±20 cd/m , 6500 parameter is x = 313 ±28, y = 329 ±28, Y = 180 ±20 cd/m...
DELL E152FPc Max Brightness measurement: a. Switch to the full white pattern, in user mode main menu: 1. Set <Color Settings> Red, Green, and Blue to the max. 2. Set <Brightness> Brightness, Contrast to the max. b. The Minimum brightness is 200cd/m ±20...
DELL E152FPc 11. BILL OF MATERIAL LIST CBPC560KSLDLN CONVERSION BOARD FOR DL KEPC560KDE1 KEY BOARD FOR T560K*DEL PWPC1542SED1 POWER BOARD 11G6036 1 SPACER SUPPORT SCC-24 15G5996 1 REAR COVER 23L3178700 1A LOGO 26L 800700 4A6444 BARCODE 33L4669 GV C POWER BUTTON...
DELL E152FPc 12.DEFINITION OF PIXEL DEFECTS 12.1 VISUAL INSPECTION...
Page 53
DELL E152FPc 12.2 ELECTRICAL INSPECTION Definitions/ Notes: - A bright dot any Red, Green, or Blue pixel sucks in the “On” mode. - A dark dot any Red, Green, or Blue pixel sucks in the “Off ” mode. - Inspection pattern for electrical defect should be pure R, G, B, and Black and White.
Page 54
DELL E152FPc Fig. 1. Bright dot defect description (two adjacent) * Adjacent two dots in horizontal direction will be considered as one dot Fig. 2. Dark dot defect description (two adjacent)
Page 55
DELL E152FPc Fig. 3. Minimum distance between dot defects bright dot - to - bright dot dark dot - to - dark dot * Adjacent two dots in horizontal direction will be considered as one dot. * A minimum distance criterion is applied for dots defect only.