Husqvarna CTH150 XP Instruction Manual

Husqvarna ride-on mower owner's manual

Hide thumbs Also See for CTH150 XP:

Owner's manual (53 pages)

Table of Contents

Quick Links

Summary of Contents for Husqvarna CTH150 XP

Page 1 CTH150 XP, CTH180 XP CTH210 XP Instruction manual Please read these in struc tions care- ful ly and make sure you un der stand them before using this ma chine. Anleitungshandbuch Bitte lesen Sie diese Anleitungen sorg- fältig durch und vergewissern Sie sich, daß...
Page 2 Safety rules. Sicherheitsvorschriften. Règles de sécurité. Assembly. Zusammenbau. Montage. Functional description. Funktionsbeschreibung. Description du fonctionnement. Before starting. Maßnahmen vor dem Anlassen. Avant de démarrer. Driving. Betrieb. Conduite. Maintenance, adjustment. Wartung (Instandhaltung), Einstellung. Manutenzione. Entretien, réglages. Troubleshooting. Störungssuche. Recherche des pannes. Storage.
Page 3: Safe Operation Practices For Ride-On Mowers
Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I. Training • Read the instructions carefully. Be familiar with the con trols and the proper use of the equipment.
Page 4: Maintenance And Storage
• Reduce the throttle setting during engine run-out and, if the engine is provided with a shut-off valve, turn the fuel off at the conclusion of mowing. IV. Maintenance and Storage • Keep all nuts, bolts and screws tight to be sure the equip- ment is in safe working condition.
Page 5: Betrieb
Regeln für die sichere Bedienung von Rasentraktoren WICHTIG: DIESE MÄHMASCHINE KANN HÄNDE UND FÜSSE ABTRENNEN UND GEGENSTÄNDE MIT HOHER GESCHWINDIGKEIT SCHLEUDERN. NICHTBEACHTUNG DER FOLGENDEN SICHERHEITSVORSCHRIFTEN KÖNNTE SCHWERE ODER TÖDLICHE VERLETZUNGEN ZUR FOLGE HABEN. I. SCHULUNG • Die Anleitungen sorgfältig durchlesen. Mit den Bedien- ungselementen und der vorschriftsmäßigen Bedienung der Maschine vertraut machen.
Page 6: Wartung Und Lagerung
- Den Motor abstellen und den Zündschlüssel abzie- hen. • Alle Anbaugeräte-Antriebe ausschalten, den Motor abstel- len und das (die) Zündkerzenkabel abziehen bzw. den Zündschlüssel abziehen: - vor dem Entfernen von Verstopfungen aus dem Mäh- werk oder dem Auswurf; - vor dem Prüfen, Reinigen oder Reparieren des Rasenmähers;...
Page 7: Règles De Sécurité
Conseils pour l’utilisation en toute sécurité des tracteurs de pelouse ATTENTION: CE TRACTEUR DE PELOUSE EST CAPABLE D’AMPUTER MAINS OU PIEDS ET DE PROJETER DES OBJETS.L’INOBSERVATION DES RÈGLES DE SÉCURITÉ CI-DESSOUS PEUT ÊTRE LA CAUSE DE BLESSURES SÉRIEUSES VOIRE MORTELLES. I.
Page 8: Entretien Et Entreposage
• Avant de quitter le siége : - débrayer les lames et abaisser le carter de coupe, - mettre le levier de vitesse au point mort et enclencher le frein de parking, - arrêter le moteur et retirer les clés, •...
Page 9: Operación
Prácticas de Operación Seguras para las Segadoras Conducibles IMPORTANTE: ESTA MAQUINA CORTADORA ES CAPAZ DE AMPUTAR LAS MANOS Y LOS PIES Y DE LANZAR OBJETOS. SI NO SE OBSERVAN LAS INSTRUCCIONES DE SEGURIDAD SIGUIENTES SE PUEDEN PRODUCIR LESIONES GRAVES O LA MUERTE. I.
Page 10: Mantenimiento Y Almacenamiento
• Desenganche la transmisión a los accesorios, pare el mo- tor, y desconecte el (los) cable (s) de la bujía o remueva la llave de ignición - antes de limpiar bloqueos o desatrancar del con- ducto; - antes de inspeccionar, limpiar o trabajar sobre la segadora;...
Page 11: Norme Antinfortunistiche
Regole di sicurezza per trattorini da prato ATTENZIONE: QUESTO TRATTORINO TOSAERBA HA UNA POTENZA SUFFICIENTE AD AMPUTARE MANI E PIEDI E A SCAGLIARE OGGETTI. LA MANCATA OSSERVANZA DELLE SEGUENTI ISTRUZIONI ANTINFORTUNISTICHE POTREBBE CAUSARE LESIONI GRAVI E PERSINO IL DECESSO DELLA VITTIMA. I.
Page 12 • Disinnestare la trasmissione del moto agli accessori, spegnere il motore e scollegare i ﬁ li delle candele op- pure togliere la chiavetta di accensione: - prima di pulire eventuali intasamenti e pri ma di stasare lo scivolo; - prima di interventi o controlli sul tosaerba e prima delle operazioni di pulizia;...
Page 13 Veilige bedieningsmethoden voor zittrekkers BELANGRIJK: DEZE MAAIMACHINE KAN HANDEN EN VOETEN AMPUTEREN EN VOORWERPEN WEGSLINGEREN. HET NIET OPVOLGEN VAN DEZE VEILIGHEIDSINSTRUCTIES KAN ERNSTIG OF DODELIJK LETSEL TOT GEVOLG HEBBEN. I. TRAINING • Lees de instructies aandachtig. Zorg dat u vertrouwd bent met de bedieningselementen en het juiste gebruik van de machine.
Page 14: Onderhoud En Opslag
MADE IN U.S.A. ORANGEBURG, SC 29116 2005 EN836:1997/A2 ISO 3744 ISO 11094 Vibration Vibration SERIAL NO. Vibración Vibrering Vibrasjon 02682 CTH150 XP CTH180 XP 15/11,2 18/13,4 0-7,3 0-7,3 38-102 38-102 98/37/EC LpA < 90 dBa 2000/14/EC LwA < 100 dBa EN 1033 Lärmpegel...
Page 15 These symbols may appear on your machine or in the literature supplied with the product. Learn and understand their meaning. Diese Symbole ﬁ nden Sie auf Ihrer Maschine oder in Unterlagen, die mit dem Produkt ausgehändigt wurden. Bitte machen Sie sich mit deren Bedeutung vertraut.
Page 16 These symbols may appear on your machine or in the literature supplied with the product. Learn and understand their meaning. Diese Symbole ﬁ nden Sie auf Ihrer Maschine oder in Unterlagen, die mit dem Produkt ausgehändigt wurden. Bitte machen Sie sich mit deren Bedeutung vertraut.
Page 17 01738 GEFAHR AUGEN SCHÜTZEN EXPLOSIVE GASE KÖNNEN ERBLINDUNG UND KÖRPERVERLET- ZUNGEN VERURSAC- HEN. GEVAAR OGEN BESCHERMEN EXPLOSIEVE GASSEN KUNNEN BLINDHEID OF LETSEL VERO- ORZAKEN. PELIGRO PROTEJE SUS OJOS GASES EXPLOSIVOS PUEDEN CAUSAR CE- GUE-DAD O LESIONES. PERICOLO RIPARARE GLI OCCHI VAPORI ESPLOSIVI PUO’...
Page 18: Steering Wheel
2. Assembly. 2. Zusammenbau. 2. Montage. 2. Montaje 2. Montaggio. 2. Montering. Before the tractor can be used certain parts must be as- sem bled, which for transportation reasons are enclosed in the packing. Vor der Anwendung des Aufsitzmähers müssen gewisse Teile eingebaut werden, die aus Transportgründen in der Verpack-ung lose beigefügt sind.
Page 19: Volante De Dirección
VOLANT DE DIRECTION • Monter la rallonge d'arbre de direction (1). • Positionner le cache sur la colonne de direction. S'assurer que les ergots du cache colonne de direction sont bien clipsés dans les quatre oriﬁ ces du tableau de bord. •...
Page 20 02464 Seat Remove the hardware securing seat to the cardboard pack ing and set the hardware aside for assembly of seat to tractor. Pivot seat upward and remove from cardboard packing. Re- move the cardboard packing and discard. Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan (1).
Page 21 NOTE: Check that the ﬂ ex is correctly con nect ed to the safe ty switch (3) on the seat hold er. HINWEIS: Prüfen, daß das Kabel richtig an dem Sicherheitsschalter (3) auf dem Halter des Sitzes angeschlossen ist. REMARQUE: Vériﬁ...
Page 22 1. Battery Cover 1. Tapador del 2. Cable Positive (+) 2. Cable positivo (+) 3. Cable Negative (-) 3. Cable negativo (-) 4. Fender 4. Protección 5. Battery terminal 5. Terminal de batería 6. Battery 6. Batería 1. Batterieabdeckung 1. Coperchio dellí 2.
Page 23 WARNING: Positive terminal must be con nect ed ﬁ rst to prevent sparks from ac ci den tal grounding. Remove terminal caps and discard. Connect the red cable to + and then the black earth ca ble to -. Screw tight the cables.
Page 24 To install bagger com po nents to tractor 1. Dis charge Chute 2. 3/8 Nut 3. Flat Washer • Remove discharge chute from rear of tractor. Unhook the two (2) straps and pull chute out and away from tractor. • Remove the two (2) 3/8 nuts and ﬂ...
Page 25: Horizontal Adjustment
1. Front bagger tube 2. Lower bagger tube 3. 1/4 x 50,8mm Car riage Bolts 4. 1/4 Lock nut 1. Front bagger tube 2. 1/4 x 50,8mm Car riage Bolts 3. 1/4 Lock nut 4. Vinyl Binding 5. Dump handle tube 6MM (1/4") - 9MM (3/8") 6.
Page 26 Installation der Aufhängung der Grasfangbox des Traktors 1. Auswurfkanal 2. Kontermutter 3/8 3. Flache unterlegscheibe • Nehmen Sie den Auswurfkanal aus dem hinteren Teil des Traktors. Lösen Sie beide (2) Klammern und ziehen Sie den Kanal aus dem Traktor. • Entfernen Sie die zwei (2) 3/8-Zoll-Muttern und ﬂ...
Page 27 1. Vorderer Rahmen der Grasfangbox 2. Unterer Rahmen der Grasfangbox 3. Tragbolzen 1/4 x 50,8mm 4. Kontermutter 1/4 1. Vorderer Rahmen der Grasfangbox 2. Bolzen 3. Kontermutter 1/4 4. Vinylverkleidung 5. Rohr des Handgriffs zum Entleeren der Grasfang- 6MM (1/4") - 9MM (3/8") 6.
Page 28 Assemblage des composants du collecteur 1. Goulotte d'éjection 2. Ecrou 3/8 3. Rondelle plate • Retirer la goulotte d'éjection (1). Pour cela, libérer les deux attaches élastiques à l'arrière du tracteur et tirer la goulotte d'éjection hors du tracteur. • Dévisser et retirer les deux écrous ainsi que les deux rondelles plates des vis situées sur le panneau arrière du tracteur (Voir ﬁ...
Page 29 1. Armature frontale 2. Armature inférieure 3. Boulon poêlier 1/4 x 50,8 mm 4. Ecrous freins 1/4" 1. Armature frontale 2. Boulon poêlier 1/4 x 50,8 mm 3. Ecrous freins 1/4 4. Bande d’étanchéité en vinyle 5. Levier de vidage du collecteur 6.
Page 30 Para montar los componentes del contenedor para costales al tractor 1. Descarga de adaptarse 2. Tuercas de 3/8 3. Arandelas planas • Quite el colector de la parte trasera del tractor. Desbloquee las dos (2) grapas y tire el colector fuera del tractor. •...
Page 31 1. Tubos frontales del contenedor 2. Tubos inferiores del contenedor 3. Tornillos por tadores 1/4 x 50,8mm 4. Contratuercas 1/4 1. Tubos frontales del contenedor 2. Tornillos14x50,8 mm 3. Contratuercas 1/4 4. Capas de vinil 5. Tubo de la manilla 6.
Page 32 Per montare i componenti del cesto di raccolta 1. Convogliatore di scarico 2. Dadi 3/8 3. Rondella Piatta • Rimuovere il convogliatore dalla parte posteriore del trattore. Allentare le due graffe, sganciare ed estrarre il convogliatore. • Rimuovere i due (2) dadi da 3/8 e le rondelle piatte dai bulloni sulla piastra posteriore del trattore.
Page 33 1. Piastrina d'arresto dell'asta di scarico 2. Telaio inferiore del cesto 3. Bulloni di supporto 1/4 x 50,8 mm 4. Dadi 1/4 1. Telaio anteriore 2. Bulloni 1/4 x 50,8 3. Dadi 1/4 4. Rivestimento in plastica 5. Asta di scarico 6.
Page 34 Hetmonteren van componenten van de grascontainer op de trekker 1. Afvoertrechter 2. 3/8 borgmoer 3. Vlakke sluitring • Verwijder de afvoertrechter van de achterzijde van de trek ker. Haak de twee (2) riemen los en trek de trechter van de trekker af. •...
Page 35 1. Voorstenn 2. Onderste container steun 3. 1/4 x 50,8 mm slotbouten 4. 1/4 Borgmoer 1. Voorstenn 2. 1/4 x 50.8 mm bouten 3. 1/4 Borgmoeren 4. Vinylafdichting 5. Hendel voor legen 6. Vorkbout 7. Sluitveer 8. Hetten 6MM (1/4") - 9MM (3/8") 1.
Page 36 To assemble and install mulcher plug • Remove spring retainer and pin from handle. • Insert plug into handle. Make sure that the letter "A" on both the plug and handle are on the same side and that they can both be seen from the top when laying on the ground.
Page 37 TO ADJUST GAUGE WHEELS Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain con di tions. •...
Page 38 3. Functional description. 3. Funktionsbeschreibung. 3. Description du fonctionnement. 3. Descripción del funcionamiento. 3. Funzionamento. 3. Beschrijving van functies Positioning of controls 1. Light Switch position. 2. Throttle control. 3. Brake and clutch pedal. 4. Motion Control Lever. 5. Attachment clutch switch. 6.
Page 39 Positioning of controls 1. Interrupteur de commande des phares. 2. Commande des gaz (Accélérateur). 3. Pédale d'embrayage et de frein. 4. Levier de commande dela trans mis sion hydrostatique. 5. Embrayage/débrayage du carter de coupe. 6. Relevage et abaissement du carter de coupe. 7.
Page 40 1. Light switch position 1. Lichtschalter 1. Interrupteur des phares 1. Interruptor de alumbrado 1. Interruttore luci 1. Schakelaar verlichting 2. Throttle control The throttle control regulates the engine revs and thus the rotation speed of the blades. = Full speed = Idling speed 2.
Page 41 3. Brake and clutch pedal When the pedal is pushed down the brake is applied and the motor is disengaged. 3. Brems- und Kupplungspedal Beim Vorwärtsdrücken des Pedals wird das Fahrzeug abge- bremst. Gleichzeitig wird der Motor ausgekuppelt und das Fahrzeug rollt aus.
Page 42 01952 01350 6. Quick lifting/lowering of the cutting unit Pull the lever backwards to quickly lift the cutting unit when passing over irregularities in the lawn, etc. During trans por - ta tion the cutting unit shall be in the highest position. Pull the lever back until it locks.
Page 43 7. Ignition Lock There are three different positions for the ignition key: All electric current bro ken. Electric current connected. START Start motor connected. WARNING! Never leave the key in the ignition lock when leaving the machine on its own. 7.
Page 44 8. Frein de stationnement Pour enclencher le frein de stationnement : 1. Enfoncer à fond la pédale d'embrayage/frein. 2. Relever vers le haut le levier du frein de stationnement et le maintenir dans cette po si tion. 3. Relâcher la pédale d'embrayage/frein. Relâcher le levi er du frein de stationnement qui restera dans sa position verrouillée (en haut).
Page 45 10. Cutting height setting The required cutting height is set with the aid of the wheel. The cutting height is increased when it is turned clockwise. The wheel is easier to turn if the lever for lifting/lowering of the cutting unit is pulled backwards at the same time. 10.
Page 46 4. Before starting. 4. Maßnah men vor dem Anlassen. 4. Avant de démarrer. 4. Antes del arranque. 4. Prima dell’avviamento. Filling up The en gine should be run of pure (not oil mixed) un lead ed petrol. Do not ﬁ ll beyond the lower edge of the ﬁ lling hole. Do not ﬁ...
Page 47 Oil level The combined oil reﬁ lling cap and the oil stick is ac ces si ble when the bonnet is lifted for wards. The oil level in the engine should be checked before each run. Make sure that the tractor is ho ri zon tal.
Page 48 Tire air pressure Check the tire pressure regularly. The pres sure in the front tire should be 1 bar (14 PSI) and 0.8 bar (12 PSI) in the back tires. Reifendruck Den Luftdruck in den Reifen regelmäßig prüfen. Der Druck in den Vorderreifen soll 1 bar betragen, in den Hinterreifen 0,8 bar.
Page 49 5. Driving. 5. Betrieb. 5. Conduite. 5. Conducción. Starting of motor Make sure that the cutting unit is in the transport position (top position) and that the lever for connection/disconnection of the cutting unit is in the disconnection position. Anlassen des Motors Darauf achten, daß...
Page 50 Pull out the choke control (if engine is cold). Den Kaltstarthebel herausziehen (nur bei kaltem Motor). Si le moteur est froid : Tirer la commande de starter. Extraer el estrangulador (únicamente si el motor está frío). Estrarre il comando dello choke (in caso di partenza a freddo).
Page 51 Turn the ignition key to “START position”. NOTE! Do not run the start motor more than 5 sec onds at once. If the engine will not start, wait about 10 sec onds before the next try. Zündschlüssel auf “START” drehen. HINWEIS! Den Anlasser nicht jeweils länger als ca.
Page 52 IMPORTANT! COLD STARTING FOR HYDRO COLD STARTING FOR HYDRO (BE LOW 40°F[4°C]) - AF TER STARTING ENGINE AND BEFORE DRIVING, LET TRANS- MISSION WARM UP FOR ONE (1) MINUTE BY PLACING MOTION CONTROL LEVER IN NEU TRAL (N) PO SI TION AND RELEASING CLUTCH/BRAKE PEDAL.
Page 53 • Démarrer le moteur et mettre la commande des gaz en position de ralenti. S'assurer que le frein de stationnement n'est pas serré. • Déplacer à fond le levier de commande d'avancement en position de marche avant et le maintenir ainsi pendant 5 secondes.
Page 54 NOTE! The machine is equipped with a safety switch which immediately breaks the current to the en gine if the driver leaves the seat with en gine run ning and with the con nec tion/dis con nec tion le ver in position “connection”.Your machine is also equipped with a system that will not allow mower to operate if the bagger or op tion al rear discharge deﬂ...
Page 55 Cutting tips • Clear the lawn from stones and other objects which can be thrown away by the blades. • Localize and mark stones and other ﬁ xed objects to avoid collision. • Begin with a high cutting height and reduce until the required cutting result is obtained.
Page 56 02207 To Dump Bagger Your tractor is equipped with a Dump Bag Alarm. To turn off the alarm disengage the attachment clutch switch. • Position tractor in location you wish to dump bagger. • Place motion control lever in Neutral position and set parking brake.
Page 57 To convert mower (Converting to mulching or rear discharging will re quire the purchase of these ac ces so ries.) To mulching • Place deck into the high cut position. • Remove bagger or optional rear discharge deﬂ ector. • Unhook the two (2) straps and remove discharge chute.
Page 58 Para cambiar el ajuste de la segadora (Un cambio de ajuste para no recoger la hierba o usarla tipo mulching requiere la compra de los mecanismosdispositivos siguientes) Para cortar tipo mulching • Meta la plataforma en posicion de siega alta •...
Page 59 WARNING! • Do not drive in terrain at an angle of more than max. 5°. The risk for spark-over back wards is large. • In steep terrain the risk for tipping is considerable. • Avoid stopping and starting in sloping terrain. WARNUNG! •...
Page 60 WARNING! Do not leave the ignition key in the machine when not in use to prevent children and other unauthorized persons start ing the en gine. WARNUNG! Den Zündschlüssel niemals im Zündschloß sitzen lassen, wenn die Machine unbeaufsichtigt verlassen wird, damit nicht Kinder und unbefugte Personen den Motor anlassen können.
Page 61 6. Maintenance, adjustment. 6. Wartung (Instandhaltung), Einstel- lung. 6. Entretien, réglages. 6. Mantenimiento, ajuste. 6. Manutenzione. 6. Onderhoud, afstelling. WARNING! Before servicing the engine or cutting unit the fol low ing shall be carried out: • Press down the clutch/brake pedal and engage the park- ing brake lever.
Page 62 02495 (1) Hood (2) Headlight wire connector (1) Motorhaube (2) Scheinwerferanschluß (1) Capot (2) Connexion des phares (1) Cubierta (2) Conector de cables de los faros delanteros (1) Cofano (2) Connettore cavo luci (1) Motorkap (2) Aansluitkabel koplampen Engine hood •...
Page 63: Wartung
Maintenance NOTE: Periodic maintenance should be performed on a regular basis in order to keep your tractor in good running condition. WARNING: Disconnect spark plug wire to prevent ac ci - den tal starting before attempting any repair, inspection, or main te nance.
Page 64 To service engine See engine manual. Oil drain valve • Remove cap and install drain tube. • To open valve, push in slightly, turn counterclockwise and pull out. • To close valve, push in and turn clockwise . • Remove drain tube and install cap. 1.
Page 65 SERVICE RECORD Fill in dates as you complete regular service Change engine oil (without oil ﬁ lter) ... Change engine oil (with oil ﬁ lter) ... Lubricate pivot points ... Check brake operation ... Clean air screen ... Clean air ﬁ lter and pre-cleaner... Replace air cleaner paper cartridge...
Page 66 SCHEMA D'ENTRETIEN Consigner les dates d'intervention après chaque opération d'entretien. Vidange de l'huile moteur (sans ﬁ ltre à huile Vidange de l'huile moteur (avec ﬁ ltre à huile) ... Graissage des articulations... Vériﬁ cation des freins ... Nettoyage de la grille d'aération ... Nettoyage du ﬁ...
Page 67 DATI DI SERVIZIO Compilare ogni qualvolta si esegue un regolare servizio Cambio dell'olio (Senza ﬁ ltro dell’olio)... Cambio dell'olio (Con ﬁ ltro dell’olio) ... Lubriﬁ cazione punti di articolazione ... Controllo freni... Pulizia schermo aria... Pulizia ﬁ ltro aria e preﬁ ltro... Sostituzione depuratore aria ...
Page 68 Blades The blades should be sharp to achieve best cutting results. Sharpening can be carried out with a ﬁ le or grinding disc. NOTE: It is very important that both blades are sharpened equally to avoid imbalance. Messerbalken Für ein gutes Mähergebnis müssen die messcrbalken scharf sein.
Page 69 1. Hex bolt right hand 5. 5 Star Center Hole thread ed. 6. 5 Star Pattern 2. Lock Washer 7. Trailing Edge 3. Flat Washer 8. Mandrel Assembly 4. Blade 1. Sechskantschraube mit 5. Fünfeckige Rechtsgewinde Zentrierbohrung 2. Federscheibe 6. Fünfeckige Messeraufnahme 3.
Page 70 1. Tornillo de cabeza de 5. Oriﬁ co de centraje-es- cinco facetas, dextrogiro 6. Mandril-estrella de cinco 2. Arandela elastica 3. Arandela pla na 7. Canto (auxiliar 4. Filo cortador 8. Nudo del mandril 1. Bullone a testa 5. Foro stellare a cinque esagonale con ﬁ...
Page 71 For best results mower blades must be kept sharp. Re place bent or damaged blades. BLADE REMOVAL • Raise mower to highest position to allow access to blades. • Remove hex bolt, lock washer and ﬂ at washer se cur ing blade.
Page 72 Brakes The brakes are located inside the right rear wheel. The wheel should be dismantled for best ac cess. • Press down the clutch/brake pedal and engage the park- ing brake. Bremse Die Bremse sitzt innerhalb des rechten Hinterrades. Für beste Zugänglichkeit ist das Rad auszubauen.
Page 73 Dismantling of the cutting unit Work from the right side of the machine. 1. Take off the belt from the engine pulley (1). 2. Remove the two rear retainer springs (2) and knock off the axle taps with a hammer. 3.
Page 74 Replacement of drive belt for cutting unit 1. Dismantle the cutting unit as described previously. 2. Work off the belt from the unit's left pulley and then from the other wheels. 3. Pull the belt away from the cutting unit. 4.
Page 75 Adjustment of the cutting unit A. In the direction of travel 1. Check that the air pressure is correct in all four tires. 2. Make sure that the machine is on a horizontal surface. 3. Lift up the cutting unit to its highest position. 4.
Page 76 00598 “A” (1) Bottom edge of mower (2) Lift link adjustment nut (1) Unterkante des Mähwerks (2) Hubstangen-Stellmutter (1) Extrémités du carter de coupe (2) Ecrou de réglage du bras de suspension arrière (1) Parte inferior de la esquina de la segadora (2) Tuerca de ajuste del várillaje de levantamiento (1) Bordo inferiore del tagliaerba (2) Dado di regolazione dell'articolazione di sollevamento...
Page 77 Replacement of drive belt 1. Dismantle the cutting unit as described pre vi ous ly. 2. Pull apart the contact for the cable to the elec tri cal con- nection (1). 3. Dismantle the motion restrainer for the clutch (2). 4.
Page 78 1. Motion Control Lever 2. Neutral Lock Gate 3. Adjustment Bolt 1. Steuerknüppel 2. Verschlussperre in Leerlaufstellung 3. Einstellbolzen 1. Levier de la commande d'avancement 2. Encoche de position neutre (N) (point mort) 3. Vis de réglage TRANSAXLE MOTION CONTROL LEVER NEUTRAL AD JUST MENT The motion control lever has been preset at the factory and adjustment should not be nec es sary.
Page 79 1. Palanca de Control Del Movimento 2. Neutro Cierre Metálico 3. Perno de Regulación 1. Leva Di Comando Del Movimento 2. Blocco In Posizione Folle 3. Bullone Di Regolazione 1. Stuurbedieningshandel 2. Vrijloop-Sluitboomgrendel 3. Stelbout REGULACIÓN DE LA PALANCA DE CONTROL DEL MOVIMIENTO DEL CAMBIO MECÁNICO La palanca de control del movimiento del cambio mecánico ya viene predeﬁ...
Page 80 TRANSAXLE COOLING The fan and cooling ﬁ ns of transmission should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. • Inspect cooling fan to be sure fan blades are intact and clean.
Page 81 7. Troubleshooting. 7. Störungssuche. Engine will not start 1. No fuel in fuel tank. 2. Plug defective. 3. Plug connection defective. 4. Dirt in carburetor or fuel pipe. Start motor will not turn engine 1. Battery ﬂ at. 2. Poor contact between cable and battery pole. 3.
Page 82 7. Recherche des pannes. 7. Búsqueda de averías. Le moteur ne démarre pas 1. Manque de carburant dans le réservoir. 2. Bougie d'allumage défectueuse. 3. Le câblage de la bougie d'allumage défectueux. 4. Il y a des impuretés dans le carburateur ou dans le circuit du carburant.
Page 83 7. Ricerca guasti. 7. Het localiseren van fouten. Il motore non parte 1. Manca il carburante. 2. Difetto di candela. 3. Collegamento della candela difettoso. 4. Sporco nel sistema di alimentazione e o nel carbura- tore. Il motorino di avviamento non fa girare il mo- tore 1.
Page 84 8. Storage. 8. Aufbewahrung. 8. Remisage. 8. Conservación. The following steps should be taken when mowing season is over: • Clean the entire machine, especially underneath the cut ting unit cover. Do not use high pressure washer for cleaning. Water can enter engine and transmission and shorten the useful life of the machine.
Page 85 8. Rismessaggio. 8. Stallen. Al termine della stagione effettuare i seguenti inter- venti: • Pulire tutto il tagliaerba e particolarmente sotto il co per chio della falciatrice. Per le operazioni di pulizia, non utilizzare acqua ad alta pressione. L’acqua può inﬁ ltrarsi nel motore e nel sistema di trasmissione, riducendo quindi così...
Page 88 532 19 39-70 Rev. 1 01.28.05 TR Printed in U.S.A.

This manual is also suitable for:

Cth210 xp Cth180 xp

Husqvarna CTH150 XP Instruction Manual

Quick Links

Related Manuals for Husqvarna CTH150 XP

Summary of Contents for Husqvarna CTH150 XP

This manual is also suitable for:

Table of Contents