SERVICING NOTICES ON CHECKING 1. KEEP THE NOTICES 6. AVOID AN X-RAY As for the places which need special attentions, Safety is secured against an X-ray by consider- they are indicated with the labels or seals on the ing about the cathode-ray tube and the high cabinet, chassis and parts.
GENERAL SPECIFICATIONS CRT Size / Visual Size 27 inch / 676mmV System CRT Type Normal Deflection degree Magnetic Field BV/BH +0.45G/0.18G Color System NTSC Speaker 2Speaker Position Front Size 2.0 x 3.5 Inch Impedance Sound Output 2.5 + 2.5 W 10%(Typical) 2.0 + 2.0 W NTSC3.58+4.43 /PAL60Hz...
Page 4
GENERAL SPECIFICATIONS On Screen Menu Display Menu Type Icon Picture Contrast Brightness Color Tint Sharpness Sound Bass Treble Balance BBE On/Off Stable Sound On/Off Set Up TV/CABLE(CATV) CH Program Add/Erase Option Language V-chip CH Label Favorite CH Color Stream DVD/DTV Control Level Volume Brightness...
Page 5
GENERAL SPECIFICATIONS G-10 Remote Unit RC-DU Control Glow in Dark Remocon Format Toshiba Custom Code TV:40-BF h Power Source Voltage(D.C) UM size x pcs UM-4 x 2 pcs Total Keys Keys Keys Power CH Up CH Down Volume Up Volume Down...
Page 6
Features Auto Degauss Auto Shut Off Canal+ CATV Anti-theft Rental Memory(Last CH) Memory(Last Volume) V-Chip Type USA,Toshiba Type Auto Search CH Allocation Channel Lock Just Clock Function Game Position CH Label VM Circuit Full OSD Premiere Comb Filter 2 Lines...
Page 7
GENERAL SPECIFICATIONS G-13 Interface Switch Front Power System Select Main Power SW Sub Power Channel Up Channel Down Volume Up Volume Down Rear AC/DC TV/CATV Selector Degauss Main Power SW Indicator Power Stand-by On Timer Terminals Front Video Input Audio Input RCA x 2 Other Terminal Rear...
DISASSEMBLY INSTRUCTIONS 3. After one side is removed, pull in the opposite direction to 1. REMOVAL OF ANODE CAP remove the other. Read the following NOTED items before starting work. NOTE After turning the power off there might still be a potential Take care not to damage the Rubber Cap.
DISASSEMBLY INSTRUCTIONS REMOVAL AND INSTALLATION OF When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using FLAT PACKAGE IC a tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 2-3.) REMOVAL NOTE Put the Masking Tape (cotton tape) around the Flat...
Page 10
DISASSEMBLY INSTRUCTIONS INSTALLATION When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thin- Take care of the polarity of new IC and then install the tip Soldering Iron. (Refer to Fig. 2-8.) new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily.
SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter the Service Mode, press both set key and remote control key for more than 1 second. Set Key Remocon Key Operations Releasing of V-CHIP PASSWORD.
ELECTRICAL ADJUSTMENTS BEFORE MAKING ELECTRICAL 2. BASIC ADJUSTMENTS ADJUSTMENTS 2-1: CONSTANT VOLTAGE Read and perform these adjustments when repairing the Set condition is AV MODE without signal. circuits or replacing electrical parts or PCB assemblies. Connect the digital voltmeter to TP002. Adjust the VR502 until the digital voltmeter is 135 ±...
Page 13
ELECTRICAL ADJUSTMENTS 2-7: VERTICAL LINEALITY 2-12: SEPARATION 1, 2 Receive the stereo signal (L=2KHz, R=400Hz). NOTE: Adjust after performing adjustments in section 2-6. Connect the AC voltmeter to AUDIO OUT JACK though Receive the center cross signal from the Pattern stereo filter (L=400Hz, R=2KHz).
Page 14
ELECTRICAL ADJUSTMENTS 2-15: SUB TINT/SUB COLOR 2-16: Confirmation of Fixed Value (Step No.) Receive the color bar pattern. (RF Input) Please check if the fixed values of the each adjustment Connect the oscilloscope to TP806. items are set correctly referring below. Activate the adjustment mode display of Fig.
ELECTRICAL ADJUSTMENTS PURITY AND CONVERGENCE 3-3: STATIC CONVERGENCE ADJUSTMENTS NOTE Adjust after performing adjustments in section 3-2. NOTE Receive the crosshatch pattern from the color bar Turn the unit on and let it warm up for at least 30 generator. minutes before performing the following adjustments.
TV BLOCK DIAGRAM SPEAKER SP1001 TU001 MICON IC101 OEC7054A SOUND AMP IC1001 AN5276 YUV IN IF/CHROMA/AUDIO IC201 TB1253N 24 25 43 44 18 19 V OUT IC902 AN5829S TONE CONTROL IC303 10 SCL M62420SP COMB FILTER IC1501 TC90A45F YUV IN S INPUT AV SWITCH IC701...
POWER SCHEMATIC DIAGRAM 6.3A 125V CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE 6.3A 125V(F501) ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES D’INCEIE N’UTILISER QUE DES FUSIBLE DE MEME TYPE 6.3A 125V(F501) (MAIN PCB) D516 RELAY DRIVE Q504...
Page 25
SOUND SCHEMATIC DIAGRAM (MAIN PCB) FROM/TO AV R314 AUDIO_R R324 C334 AUDIO_L 1.8K 0.033 B C332 R326 C331 0.47 B 0.022 R328 1.8K TONE 136K AMP1 I2C BUS INTERFACE SIMAMP1 VOLAMP1 6.5K 6.5K 6.5K VOLAMP2 CONTROL SIMAMP2 6.5K LOGIC TONE 136K 1.8K AMP2...
Page 26
AV SCHEMATIC DIAGRAM FROM/TO CHROMA/IF (MAIN PCB) CD701A CH243001 YUV_IN(REAR) J704 AV3-19D-5 FROM/TO COMB FILTER CP1501 6035B-06Z002-T MONITOR V.OUT A/V_OUT(REAR) Y IN J203 C IN AV3-19DS-1 P.CON+5V LINE2(REAR) J703 FROM/TO POWER AV3-19DS-1 L703 P.CON+9V 47uH P.CON+5V 0305 C713 R751 GND_POWER C714 R752 C715...
Page 28
DIGITAL COMB FILTER SCHEMATIC DIAGRAM (COMB PCB) BUFFER C1525 L1506 R1511 Q1504 2SC2412K 22uH C1511 L1503 W803 820uH C1506 FROM/TO 0.01 B CP1501 6035B-06Z002-T MONITOR V.OUT Y IN C IN W807 P.CON+5V BUFFER Q1502 2SA1037AK C1501 W802 BUFFER Q1503 0.1 B BUFFER 2SC2412K Q1501...
Page 29
WAVEFORMS MICON/TUNER 2.0V 50ns/div 500mV 10µs/div 500mV 50µs/div 2.0V 50ns/div 200mV 10µs/div 100mV 100ns/div 1.0V 5ms/div 2.0V 50µs/div 1.0V 20µs/div 2.0V 50µs/div 1.0V 20µs/div 1.0V 20µs/div CHROMA/IF 200mV 10µs/div 2.0V 20µs/div 1.0V 20µs/div NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
Page 30
WAVEFORMS DEFLECTION 1.0V 5ms/div 200V 20µs/div 500mV 1ms/div SOUND 10V 5ms/div 1.0V 2ms/div 500mV 1ms/div 10V 5ms/div 1.0V 2ms/div 200mV 20µs/div 50V 20µs/div 20mV 1ms/div 200mV 20µs/div 2.0V 20µs/div 20mV 1ms/div 100mV 10µs/div NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
Page 31
50V 10µs/div 500mV 10µs/div 1.0V 1ms/div 50V 10µs/div 1.0V 1ms/div 1.0V 10µs/div 50V 10µs/div NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.