Approx. 505 (18) Included items Lens (1), Front lens cap (1), Rear lens cap (1), Lens hood (1), Set of printed documentation Designs and specifications are subject to change without notice. SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) — 2 —...
IC pins, etc. • Be sure to control soldering iron tips used for unleaded solder and those for leaded solder so they are managed separately. Mixing unleaded solder and leaded solder will cause detachment phenomenon. SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU PUBLISHED BY SONY.
Check operation of the joint tube block, Check operation and replace the of the midway move defective part. frame block. Replace the defective part. Perform the aperture diameter check. (See page 4-4.) SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
Page 7
Clean the pattern of the main flexible block. Replace the defective part or apply the grease. Replace the main flexible block. Check the operation again. Perform the brush position check/adjustment. (See page 4-16.) SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
Fixed screw Chip-B Chip Chip Fixed screw Chip-B Holes When top of tip does not reach holes or notches because the fixed screw becomes obstructive, replace the fixed screw to below. +B 3X5 7-682-546-09 SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
Page 9
1 Main Flexible Block FLANGE BACK HELP06 ADJUSTMENT HELP02 HELP04 2 Rear Light Shield Barrel HELP04 4 Main Flexible Block HELP03 3 Lens Mount Block HELP42 HELP05 5 Joint Tube Block (See Page 2-3.) FLANGE BACK ADJUSTMENT SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
Page 10
Focus ring thrust adjustment : 2 to 4 pieces HELP09 (See Page 2-4.) 3 Focus Operating Ring HELP08 2 Decoration Ring HELP10 4 Scissors Lever Block HELP10 1 Front Lens Note: Barrel When removing the decoration ring, refer to HELP07 SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
Page 11
1 Fixed Holding Tube Block BRUSH POSITION ADJUSTMENT HELP16 (See Page 2-6.) 5 Torque Spring (See Page 2-5.) HELP16 2.4 mm 1.05 mm 6 Focus Scale Plate 1.7 mm M1.6 HELP17 7 Float Ring HELP12 SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
Page 12
Select the number of slip washers A and B according to the rotation load of the torque ring support barrel. 1 Torque Ring Holder Slip washer A: 1 or 2 pieces HELP18 Slip washer B: 1 or 2 pieces SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
Page 13
5 Flexible Cover Sheet HELP31 6 Main Flexible Block HELP26 HELP26 HELP32 2.6 mm HELP34 3.9 mm 2.7 mm M1.6 4 Gear Cover 1 Focus CAM Ring A HELP29 Holder HELP25 7 Fixed Barrel HELP33 SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
Page 14
EXPLODED VIEW HELP39 HELP35 4 Focus CAM Ring B 1 Focus CAM Ring B Block Holder HELP37 3 3rd Moving Barrel 2 Focus CAM HELP38 Ring B Block HELP36 5 1 Group Lens Block HELP40 SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
Page 15
(B-40) HELP02 Adhesive bond (B-40): J-6082-614-A Apply the adhesive bond (B-40) to the three screws and tighten them as shown in the figure. Apply the adhesive bond (B-40) Apply the adhesive bond (B-40) SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
Page 16
When the flange back (f’F) adjustment, tighten the two screws tentatively as shown in the figure. Two screws Apply the grease (G-85) Coupler portion Apply the adhesive bond (B-40) Apply the anti-diffusion agent (A-20) (All circumference) Apply the grease (G-85) 5 mm SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
Page 17
Main Flexible Block Flexible PC Board (A) Attach the flexible substrate setting tape, and fold the main flexible block to fix as shown in the figure. Flexible Substrate Setting Tape Fold to attach SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
Page 18
Apply the anti-diffusion agent (A-20) Attach the joint tube block as shown in the figure. When the flange back (f’F) adjustment, tighten the two screws tentatively as shown in the figure. Two screws SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
Page 19
Apply the grease (G-35) to the instruction part of the coupler and coupler gear. Coupler Coupler Gear Apply the grease (G-35) HELP07 Align the projection of the front lens barrel to CE mark as shown in the figure, and attach it. Projection SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
Page 20
Middle Moving Frame Hole (for attaching the front lens barrel) Attaching the Decoration Ring Apply the adhesive bond (B-10) to the instruction part of the decoration ring. Apply the adhesive bond (B-10) 30 mm SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
Page 21
Apply the grease (G-15) and anti-diffusion agent (A-20) to the instruction part of the focus operation ring. Apply the grease (G-15) (All circumference) Apply the anti-diffusion agent (A-20) (All circumference) Apply the grease Apply the grease (G-15) (G-15) (All circumference) SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
Page 22
Pinch Lever Assemble the focus operation ring. Check the operation of the focus operation ring, and apply the adhesive bond (B-10) as shown in the figure. Apply the adhesive bond (B-10) Focus Operation Ring SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
Page 23
Apply the grease (F-10) to the instruction part of the fixed holding tube block. Apply the grease (F-10) (All circumference) 5 mm Cut the OHP film to the size large enough to cover the lens block, then wind it as shown in the figure. OHP Film SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
Page 24
Attach the float ring, and apply the adhesive bond (B-40) to the three screws and tighten them as shown in the figure. Apply the grease (F-10) (All circumference) Apply the Apply the adhesive adhesive bond (B-40) bond (B-40) Apply the grease (F-10) (All circumference) SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
Page 25
Attach the gear base plate block, and apply the adhesive bond (B-40) to the two screws and tighten them as shown in the figure. Apply the adhesive bond (B-40) Gear Base Plate Block Apply the grease (G-35) SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
Page 26
Apply the grease (F-10) HELP17 Match the scratch of the focus scale plate to the groove of the focus cam ring A, and attach the focus scale plate. Focus Scale Plate Scratch Groove SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
Page 27
Attach the focus range switch knob, and apply the adhesive bond (B-40) to the screw and tighten it as shown in the figure. Apply the adhesive bond (B-40) Focus Range Switch Knob Apply the grease (G-85) (All circumference) Click Base Steel Ball Focus Range Stopper Focus Range Switch Knob SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
Page 28
Apply the grease (G-15, G-85) to the instruction part of the limiter stopper plate and focus range stopper. Apply the grease (G-15) Apply the grease (G-15) Apply the grease (G-85) (Back side) Focus Range Stopper 2 mm Limiter Stopper Plate SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
Page 29
Apply the adhesive bond (LOCTITE 460) to the instruction part as shown in the figure, and attach the FH button base. Dust Proofing Tape FH Button Base Dust Proofing Tape Apply the Apply the adhesive adhesive bond bond (LOCTITE 460) (LOCTITE 460) SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
Page 30
Apply the adhesive bond (LOCTITE 460) to the instruction part of the mount index. Adhesive bond (LOCTITE 460) (Note) Note: Use adhesive bond (LOCTITE 460) or an equivalent article. Don’t use what becomes white after drying like a quick-drying glue. Apply the adhesive bond (LOCTITE 460) SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
Page 31
Apply the adhesive bond (B-10) to the instruction part as shown in the figure. Apply the grease (G-35) (All circumference) Apply the adhesive bond (B-10) 2 points for approx. 10 mm long. 10 mm SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
Page 32
Grease (G-35): J-6082-621-A Apply the grease (G-35) to the spacer adjustment washer. Attach the spacer adjustment washer as shown in the figure. Apply the grease (G-35) (Both sides) Apply the grease (G-35) (Both sides) SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
Page 33
Attach the fixed tube block to the midway move frame block. Apply the adhesive bond (B-40) to the three guide pins and tighten them. Midway Move Frame Block Apply the adhesive bond (B-40) Apply the adhesive bond (B-40) SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
Page 34
Attach the gear cover, and apply the adhesive bond (B-10, B-40) to the two screws as shown in the figure. Gear Cover Apply the adhesive bond (B-40) Main Flexible Block Apply the adhesive bond (B-10) HELP30 Attach the flexible cover sheet as shown in the figure. Reference line Flexible Cover Sheet SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
Page 35
In case that the bond is adhere to them, wipe out the adherent bond. 2Reference line 3Reference line Apply the adhesive bond (B-60) (4 points) 1Match the holes HELP32 Attach the anti refrection tape sheet as shown in the figure. Anti Refrection Tape Sheet Reference line SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
Page 36
Apply the grease (G-35) Entirely to the guide circumference circumference circumference Friction Sheet HELP34 Adhesive bond (B-40): J-6082-614-A Apply the adhesive bond (B-40) to the focus stopper and tighten it. Apply the adhesive bond (B-40) SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
Page 37
Apply the adhesive bond (B-10) to the instruction part as shown in the figure, it tightens with a universal wrench. Focus Cam Ring B Holder 10 mm Apply the adhesive bond (B-10) (2 points for approx. 10 mm long.) Focus Cam Ring B Holder SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
Page 38
Attach the focus cam ring B block to the 3rd moving barrel, and apply the adhesive bond (B-40) to the three guide pins and tighten them. 3rd Moving Barrel Apply the adhesive bond (B-40) Apply the adhesive bond (B-40) SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
Page 39
Attach the focus cam ring B block to the 3rd moving barrel, and apply the adhesive bond (B-40) to the three guide pins and tighten them. 3rd Moving Barrel Apply the adhesive bond (B-40) Apply the adhesive bond (B-40) SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
Page 40
Apply the grease (G-35) and anti-diffusion agent (A-20) to the instruction part of the focus cam ring B block. Apply the anti-diffusion Apply the grease (G-35) agent (A-20) (Entirely to the guide) (All circumference) SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
Page 41
Apply the anti-diffusion agent (A-20) and grease (G-85) to the instruction parts of the torque ring support barrel. Apply the grease (G-85) Apply the anti-diffusion agent (A-20) (Slide portion of the outer barrel: (All circumference) All circumference) SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
Page 42
(B-40) Attach the preset lever, and apply the adhesive bond (B-10) to the instruction part as shown in the figure. Preset Lever Main Spring Hook Apply the adhesive bond (B-10) Main Spring SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) HELP...
A-mount Flange back gauge J-6082-606-A attachment (43.50mm) J-6082-607-A J-6082-608-A J-10 J-11 J-12 Universal wrench Aberration Chip-A for measuring cap J-6082-609-A universal wrench 55mm J-6082-609-1 (SAL100M28) J-6082-632-A J-13 Chip-B for universal wrench J-6082-609-2 Fig. 4-1-1 SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
Page 52
Attach the chart to the 1000 mm collimator as shown in Fig. 4-1-2. Align the marks Chart 1000 mm collimator Fig. 4-1-2 Note 3: Connect the variable transformer (Output voltage: AC 100 V) to the lens test projector. SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
Page 53
MENU buttons. Check that the remaining number of recordable images on the LCD monitor is “BBBB”. Note: When “BBBB” is displayed, the camera activates in the adjustment mode. Start the lens adjustment program “LensAdjustment.exe”. SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
Note: Shoot the center of the luminance surface three times with the master lens and checking lens. Setting of Luminance box: Luminance: EV12 Setting of Lens: Focus: Infinity end Setting of Camera: ISO: Exposure Mode: shutter Speed: 1/125 Aperture: F5.6 Focus Mode: Metering: Center weighted Preset white balance: Tungsten D-R: SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
Page 55
Set the Color Calculator 2 as follows. Measured value display (Display menu): RGB+L*a*b* Measuring method (Display menu): Center Single Area Fig.4-2-4 Color space (Edit menu): sRGB Fig.4-2-5 Area size for calculate (Edit menu →Option): 256×256 Pixels Fig.4-2-6 SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
Page 56
Aperture error = Average “G” value of master lens (a) - Average “G” value of checking lens (b) Specification Aperture error = 0 ±12 2) When the aperture error is out of specification, replace the midway move frame block and perform the check again. SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
Fixed lever Heat-absorbing filter Chart Chart Filament Filament f=18 to 35 mm f=100 to 200 mm Fixed lever Chart Chart Filament Filament f=35 to 100 mm f=200 to 300 mm Lens test projector Fig.4-3-1 SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
Page 58
4) Turn the focus ring of the checking lens until the chart image projected on the screen is the sharpest at the center (y’=0). 5) Set the plane mirror to the center of the projected image (y’= 0), and adjust the projector position so that the mirror reflects the light to the center of the lens. SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
Page 59
Table 4-3-2 After the checking is completed, turn the lamp switch of the lens test projector to OFF and cool the inside of the lens test projector, then turn the fan switch to OFF. SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
Focus on fine lines on the surface. Fig.4-4-2 5) Turn the scale ring of the dial gauge until the long pointer indicates “0”. Note: This position is the flange back (f’F) = 43.50 mm. Memorize the position of short-pointer. SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) 4-10...
Page 61
Check that the infinity index of the distance scale is within the distance index width of the distance scale window as shown in the Fig. 4-4-5. If not, perform “4-4-2. Flange Back (f’F) Adjustment”. Distance index width of the distance scale window Fig. 4-4-5 After the check is completed, perform “4-5. FOCUS-SHIFT CHECK”. SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) 4-11...
Page 62
5) Calculate focus error amount using the following formula. Focus error amount = Flange back (f’F) reading - 44.56 mm Focus error amount: Amount that should be adjusted by the back adjustment washer thickness. f’F: Flange back value (Reading value) SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) 4-12...
Page 63
0.07 2-685-592-01 2-685-527-01 2-685-593-01 2-685-528-01 2-685-594-01 2-685-529-01 Table 4-4-1 Coupler Adjustment Washer Back Adjustment Washer Fig.4-4-7 Install the back adjustment washer and coupler adjustment washer, and perform “4-4-1. Flange Back (f’F) Check” again. SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) 4-13...
Check that the display of “Lens Code” and “Model Name” is correct. Note: Focus position setting is not required. Fig. 4-6-2 [End] Click the button to terminate the lens adjustment program. Turn the POWER switch of the camera to OFF. SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) 4-15...
If the NG (Red) indicator of “Position” lights, perform the “4-7-2. Brush Position Adjustment and Pattern Check”. Fig. 4-7-4 [Exit] 4) Click the button. [End] 5) Click the button to terminate the lens adjustment program. 6) Turn the POWER switch of the camera to OFF. SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) 4-16...
Page 67
Fig. 4-7-6 Perform the “4-7-1. Brush Position Check”, and adjust the A encoder brush position until the OK (Green) indicator of “Position” lights. Fig. 4-7-7 Tighten the four screws loosened in step 1). SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) 4-17...
Page 68
5) Turn the POWER switch of the camera to OFF. 6) After the pattern check is completed, apply the adhesive bond (B-10) as shown in Fig. 4-7-9. Apply the adhesive bond (B-10) Fig. 4-7-9 SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) 4-18...
Unidentified lens is connected. Communication Error, Code#:E600 Communication error with the camera Code#:F000 Input data error to DLL file Code#:F100 Setting error of USB port Code#:2531 Communication error of main signal on the camera SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro) 4-19...
Page 70
[Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)] Toolbar Printing a text Reversing the screens displayed once • To reverse the previous screens (operation) one by one, click 1. Click the Print button 2.
Page 71
Official Release — — 2007.02 Revised-1 • Change of Repair Parts (Section 1-5, Section Section Section • Change of HELP31 • Addition of guide of [About the Lens Test Projector] (Cover) • Addition of HELP42 SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)