Page 1 ERserver pSeries 7311 Model D10 and Model D20 Service Guide SA38-0627-00...
Page 3 ERserver pSeries 7311 Model D10 and Model D20 Service Guide SA38-0627-00...
Page 4 A reader’s comment form is provided at the back of this publication. If the form has been removed, address comments to Information Development, Department H6DS-905-6C006, 11501 Burnet Road, Austin, Texas 78758-3493. To send comments electronically, use this commercial internet address: aix6kpub@austin.ibm.com. Any information that you supply may be used without incurring any obligation to you.
Page 5: Table Of Contents
Contents Safety Notices. . vii Rack Safety Instructions . . vii Electrical Safety . . viii Laser Safety Information . . ix Laser Compliance . . ix Data Integrity and Verification . . xi About This Book . xiii ISO 9000 .
Page 6 Checkpoints . . 41 FRU Isolation . . 42 Chapter 3. Maintenance Analysis Procedures (MAPs) . . 43 Chapter 4. Checkpoints . 45 Chapter 5. Error Code to FRU Index . . 47 Chapter 6. Using the Service Processor. . 49 Chapter 7.
Page 7 D20 Power Supplies . 169 D20 Power Supply Bulkhead . . 172 D20 I/O Backplane . . 175 Chapter 9. Parts Information . . 179 7311 Model D10 I/O Subsystem. . 180 D10 I/O Backplane and Cooling . . 180 D10 Power and Cooling .
Page 8 Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
Page 9: Safety Notices
Safety Notices A danger notice indicates the presence of a hazard that has the potential of causing death or serious personal injury. Danger notices appear on the following pages: v viii v 53 A caution notice indicates the presence of a hazard that has the potential of causing moderate or minor personal injury.
Page 10: Electrical Safety
Electrical Safety Observe the following safety instructions any time you are connecting or disconnecting devices attached to the workstation. In the system you are about to setup or service: v The ac power interface connector is considered the main power disconnect device. v This system has redundant power supply capabilities, meaning that it has the ability to have two power supplies running simultaneously in the same system unit.
Page 11: Laser Safety Information
CAUTION: All IBM laser modules are designed so that there is never any human access to laser radiation above a class 1 level during normal operation, user maintenance, or prescribed service conditions. Data processing environments can contain equipment transmitting on system links with laser modules that operate at greater than class 1 power levels.
Page 12 Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
Page 13: Data Integrity And Verification
Users should periodically check the IBM support websites for updated information and fixes applicable to the system and related software.
Page 14 Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
Page 15: About This Book
ISO 9000 registered quality systems were used in the development and manufacturing of this product. Accessing Information Documentation for the IBM Eserver pSeries is available online. Visit the IBM Eserver pSeries Information Center at http://publib16.boulder.ibm.com/pseries/en_US/infocenter/base. v To access the pSeries publications, click Hardware documentation.
Page 16: Trademarks
The following terms are trademarks of International Business Machines Corporation in the United States, other countries, or both: v AIX v Electronic Service Agent v Eserver v IBM v LANstreamer v PowerPC v pSeries v RS/6000 Other company, product, and service names may be trademarks or service marks of others.
Page 17: Chapter 1. Reference Information
Chapter 1. Reference Information This chapter provides reference information for the Model D10 and Model D20 I/O subsystems. pSeries 7311 Model D10 Overview The Model D10 is a 19-inch, rack-mountable I/O subsystem that is attached to a processor subsystem drawer to extend the system’s capacity for I/O adapters. The I/O drawer includes redundant concurrently maintainable power and cooling.
Page 18 The following figure shows the I/O subsystem from the rear. 1 PCI adapter slot 1 6 PCI-X adapter slot 6 2 PCI-X adapter slot 2 7 RIO bus adapter card Upper connector 0 Lower connector 1 3 PCI-X adapter slot 3 8 SPCN connector card Upper connector J15 Lower connector J16...
Page 19: I/O Subsystem Pci-X Slot Led Definitions
I/O Subsystem PCI-X Slot LED Definitions The green LED (viewed on the rear of the PCI adapter cassette when installed) is used to indicate the state of the PCI slot during removal and replacement of an adapter. PCI LED (Green) Indication PCI Slot Status Definition Slot power is Off.
Page 20: D10 Power
D10 Power The following figure shows a processor subsystem and two I/O subsystems from the front. Each unit has two power supplies and two power cords for redundancy. Connect the power cords from one side of the system to one power distribution bus in the rack. Connect the power cords from the other side of the system to a different power distribution bus in the rack.
Page 21 The following table describes power supply LED indicators that are available on the Model D10. Status of LED Power Supply LED Power Source not connected Blinking green LED System power source connected, but power is not turned on Blinking green LED, visibly begins to blink System power connected, the power on button faster after the power button has been pressed.
Page 22: Subsystem Positioning And Cabling
D10 Cooling Fans mounted inside each I/O subsystem power supply and an additional fan mounted on the front of the subsystem provide cooling. The power supplies and the fan can be removed and replaced with the power turned on as long as only one is removed from the I/O subsystem at a time.
Page 23 Four I/O Subsystems, Eight I/O Subsystems: The illustration on the left shows four I/O subsystems connected to the processor subsystem using one SPCN loop. The illustration on the right shows eight I/O subsystems connected to the processor subsystem using one SPCN loop. Chapter 1.
Page 24 RIO Cabling I/O subsystems are connected to the processor subsystem through remote I/O (RIO) cable loops. The cable loops are connected to ports that are available from the rear of the processor subsystem. The RIO cables are connected in loops so that the system has two paths to each I/O subsystem.
Page 25 Eight I/O Subsystems, Two RIO Loops: The following figure shows eight I/O subsystem drawers connected to the system unit using two RIO loops. Chapter 1. Reference Information...
Page 26: D10 I/O Subsystem Locations
D10 I/O Subsystem Locations This system uses physical location codes to provide mapping of the failing field replaceable units. The location codes are produced by the processor subsystem’s firmware and AIX. For information about how to read a location code, see the service guide for the processor subsystem to which your I/O subsystem is connected.
Page 27: 7311 Model D10 I/O Subsystem Rear Locations
7311 Model D10 I/O Subsystem Rear Locations 1 PCI adapter slot 1 6 PCI-X adapter slot 6 U0. dd -P1-I1 U0. dd -P1-I6 2 PCI-X adapter slot 2 7 RIO bus adapter card U0. dd -P1-I2 U0. dd -P1.1 3 PCI-X adapter slot 3 8 SPCN connector card U0.
Page 28: Model D10 I/O Backplane Locations
Model D10 I/O Backplane Locations The following illustration of the I/O backplane identifies the primary connectors used in your subsystem. 1 PCI adapter connector 1 7 SPCN connector 2 PCI-X adapter connector 2 8 VPD module 3 PCI-X adapter connector 3 9 VPD module pin 1 orientation 4 PCI-X adapter connector 4 10 RIO bus adapter connector...
Page 29: D10 I/O Subsystem Phb
D10 I/O Subsystem PHB Each 7311 Model D10 I/O Subsystem has two PHBs through which the PCI slots are connected. Slot Slot Characteristics 64-bit 5V, 33 MHz 64-bit 3.3V, 133 MHz 64-bit 3.3V, 133 MHz 64-bit 3.3V, 133 MHz 64-bit 3.3V, 133 MHz 64-bit 3.3V, 133 MHz Chapter 1.
Page 30: D10 Location Codes
D10 Location Codes This system (processor subsystem and attached I/O subsystems) use physical location codes in conjunction with AIX location codes to provide mapping of failing field replaceable unit (FRU). The location codes are produced by the processor subsystem’s firmware and AIX. For information about how to read a location code, see the service guide for the processor subsystem to which your I/O subsystem is connected.
Page 31: 7311 Model D10 I/O Subsystem Location Code Table
7311 Model D10 I/O Subsystem Location Code Table The following table lists the location codes for a D10 I/O subsystem. The location code for the I/O subsystem connected to a system unit is U0. dd (where dd can be any number from 2 through 63).
Page 32: Pseries 7311 Model D20 Overview
pSeries 7311 Model D20 Overview The Model D20 is a 19-inch, rack-mountable I/O subsystem that is attached to a processor subsystem to extend the system’s capacity for I/O adapters and disk drives. The I/O subsystem includes redundant concurrently maintainable power and cooling. Seven PCI slots are available for PCI adapters.
Page 33 rear of the I/O drawer. 1 2 3 4 1 PCI-X Expansion Slot 1 6 PCI-X Expansion Slot 6 2 PCI-X Expansion Slot 2 7 PCI-X Expansion Slot 7 3 PCI-X Expansion Slot 3 A Green Power LEDs 4 PCI-X Expansion Slot 4 B Amber Identify LEDs 5 PCI-X Expansion Slot 5 The green LEDs for the PCI-X adapter slots (viewed on the rear of the I/O subsystem)
Page 34: Model D20 Power
Model D20 Disk Drives 12 hot-plug disk-drive bays are provided. The bays are located behind the Model D20 front bezel. The Model D20 has from 18.2 GB to 1.7 terabytes of disk storage capacity. The following disk drive sizes and speeds are available: v 18.2 GB Ultra3 10K RPM 1 inch v 36.4 GB Ultra3 10K RPM 1 inch v 73.4 GB Ultra3 10K RPM 1 inch...
Page 35 Model D20 Cooling Four blowers are mounted on the top of the I/O subsystem to provide cooling. Attention: The four cooling blowers mounted on top of the Model D20 are hot-plug. The one exception is when your subsystem has only one power supply either installed or functioning, in which case you must shut down the system and subsystem.
Page 36 Model D20 Rear View 1 PCI-X Expansion Slot 1 9 Primary Power Supply 2 PCI-X Expansion Slot 2 10 Model D20 I/O Drawer 3 PCI-X Expansion Slot 3 11 Connector J11 (Not Used) 4 PCI-X Expansion Slot 4 12 Connector J14 (Not Used) 5 PCI-X Expansion Slot 5 13 Rear Serial Number Label 6 PCI-X Expansion Slot 6...
Page 37 Model D20 Power Supply Locations 1 Power Supplies 4 Green AC Power LED 2 Amber Fault/Identify LED 5 Power Supply Filler 3 Green DC Good LED 6 Model D20 I/O Drawer Chapter 1. Reference Information...
Page 38 Model D20 Blower Locations The following illustration identifies the I/O subsystem cooling blowers. Each blower has a green power LED and an amber identify LED located on the front blower housing. The green LED indicates that a blower has power and is operating properly. The amber LED is in the identify state when blinking.
Page 39 Model D20 I/O Backplane Locations The following illustration of the I/O backplane identifies the primary connectors used in your subsystem. Note: Before replacing the I/O backplane, note the position of pin 1 on the VPD module. 1 PCI-X Adapter Connector 1 11 Disk Drive Power Connector 2 PCI-X Adapter Connector 2 12 Cooling Blower Connector...
Page 40 Model D20 Reading the Operator Panel and I/O Backplane LEDs The following illustration shows the component location on the operator panel Number Component Name Component Description Green Power LED Standby State - Blinking LED (System connected to power source but not powered on.) Powered On - LED is turned on solid (not blinking).
Page 41 Model D20 SCSI IDs and Bay Locations Index Bay Location Drive Name SCSI Bus ID 8 DB1 Hot-Plug Disk Drive 8 - DB1 9 DB1 Hot-Plug Disk Drive 9 - DB1 A DB1 Hot-Plug Disk Drive A - DB1 B DB1 Hot-Plug Disk Drive B - DB1 C DB1...
Page 42 Cabling the Model D20 to a Model 6C4 The Model D20 subsystem can be installed in any location in a standard 19-inch EIA rack. The cables that connect the subsystems allow some flexibility in drawer placement. Up to two Model D20can be connected to a Model 6C4. Each I/O subsystem is connected to the processor subsystem using a system power control network (SPCN) cable loop and a remote I/O (RIO) cable loop.
Page 43 RIO (Remote Input Output) Cabling The following rules apply to RIO cable connections: Notes: 1. To connect to a 7311 you will be using the RIO-G (Remote Input Output) and SPCN (System Power Control Network) connectors and cables. The RIO-G and SPCN cables provide two functions, remote data bus connection and power control.
Page 44 5. Lift the RIO-G cable and cable connector into the bottom of the RIO-G cable support bracket. 1 Model 6C4 2 RIO-G Cable Support Bracket 3 Slide Portion of RIO-G Cable Support Bracket 4 RIO-G Connector Support Lever 6. Pull the RIO-G connector back until the connector is seated against the support hook.
Page 45 Model 6C4 Attached to One I/O Drawer: 1 Model 6C4 3 RIO-G 0 to RIO-G 0 Cable 2 7311 4 RIO-G 1 to RIO-G 1 Cable Model 6C4 Attached to Two I/O Drawers: 1 Model 6C4 4 RIO-G 0 to RIO-G 0 Cable 2 7311 I/O Drawer 5 RIO-G 1 to RIO-G 1 Cable 3 7311 I/O Drawer...
Page 46 SPCN (System Power Control Network) Cabling The following figures provide cabling examples for all valid cabling configurations. Match your configuration to the correct figure and connect your SPCN cables as shown. Model 6C4 Attached to One I/O Drawer: 1 Model 6C4 3 SPCN 2 to SPCN 2 Cable 2 7311 4 SPCN 1 to SPCN 1 Cable...
Page 47 Model 6C4 Attached to Two I/O Drawers: 1 Model 6C4 4 SPCN 1 to SPCN 1 Cable 2 7311 I/O Drawer 5 SPCN 2 to SPCN 2 Cable 3 7311 I/O Drawer 6 SPCN 2 to SPCN 1 Cable Chapter 1. Reference Information...
Page 48 Model D20 Internal Cabling 1 Cooling Blowers (Quantity 4) 6 Disk Drive Power Connector 2 Operator Panel 7 Disk Drive SPCN Connector 3 Disk Drive Backplanes 8 Disk Drive Power/Signal Cable 53P0416 4 Cooling Blower Cable 9 Operator Panel Connector 53P0419 5 Cooling Blower Connector 10 Operator Panel Cable...
Page 49: Model D20 Location Codes
Model D20 Location Codes This system (processor subsystem and attached I/O subsystems) uses physical location codes in conjunction with AIX location codes to provide mapping of a failing field replaceable units. The location codes are produced by the processor subsystem’s firmware and AIX.
Page 50: Model D20Location Code Table
Model D20Location Code Table The following table lists the location codes for a model D20 I/O subsystem. The location code for the I/O subsystem connected to a system unit is U0. dd (where dd can be any number from 2 through 63). FRU Name Physical Location Code Model D20 I/O Drawer U0.
Page 51 FRU Name Physical Location Code Cooling Blowers Cooling blower 1 U0. dd -F1 Cooling blower 2 U0. dd -F2 Cooling blower 3 U0. dd -F3 Cooling blower 4 U0. dd -F4 SPCN Connectors SPCN connector 1 U0. dd -P1/Q3 SPCN connector 2 U0.
Page 52: Powering The System On And Off
Powering the System On and Off Power for the I/O subsystems is controlled by the attached processor subsystem and the System Power Control Network (SPCN). Power-On Self-Test After power is turned on and before the operating system is loaded, the system does a power-on self-test (POST).
Page 53: Specifications
Specifications This section contains system specifications for both the 7311 Model D10 I/O Subsystem, and the 7311 Model D20 I/O Subsystem Model D10 Specifications Dimensions 7311-D10 Two 7311-D10s with Enclosure Height 170 mm (6.6 in) 178 mm (7.0 in) Width 220 mm (8.7 in) 445 mm (17.5 in) Depth...
Page 54: Model D20 Specifications
Model D20 Specifications Dimensions Height 178 mm (7.0 in) Width 445 mm (17.5 in) Depth 610 mm (24.0 in) Maximum Weight 45.9kg (101 lbs) Electrical Power source loading 0.358 kVA (max.) Voltage range 100 to 240 V ac, V dc not supported Frequency 50 or 60 Hz Thermal output (typical)
Page 55: External Ac Power Cables
External AC Power Cables To avoid electrical shock, a power cable with a grounded attachment plug is provided. Use only properly grounded outlets. Power cables used in the United States and Canada are listed by Underwriter’s Laboratories (UL) and certified by the Canadian Standards Association (CSA). These power cords consist of the following: v Electrical cables, Type SVT or SJT.
Page 56: Service Inspection Guide
Service Inspection Guide Perform a service inspection on the system (processor subsystem and connected I/O subsystems) when: v The system is inspected for a maintenance agreement. v Service is requested and service has not recently been performed. v An alterations and attachments review is performed. v Changes have been made to the equipment that may affect the safe operation of the equipment.
Page 57: Chapter 2. Diagnostics Overview
Chapter 2. Diagnostics Overview The system uses an integrated set of software diagnostic procedures to help isolate failing components and system maintenance. This book, along with the RS/6000 Eserver pSeries Diagnostic Information for Multiple Bus Systems , is the basis of the diagnostic procedures.
Page 58: Fru Isolation
FRU Isolation For a list of error codes and recommended actions for each code, see your system’s service guide. These actions can refer to Chapter 9, “Parts Information”, on page 179, Chapter 3, “Maintenance Analysis Procedures (MAPs)”, on page 43, or provide informational message and directions.
Page 59: Chapter 3. Maintenance Analysis Procedures (Maps)
Chapter 3. Maintenance Analysis Procedures (MAPs) The maintenance analysis procedures (MAPs) provide the service representative a step-by-step procedure to analyze a problem with the system and I/O subsystem hardware. Be prepared to record code numbers and other data while using the MAPs. Because the Model D10 and Model D20 are subsystems, refer to your system’s service guide.
Page 60 Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
Page 61: Chapter 4. Checkpoints
Chapter 4. Checkpoints Checkpoints display on the system operator panel and the virtual terminal while the system unit is powering on and going through the initial program load (IPL). See the system’s service guide for descriptive information and a complete listing of all checkpoints used by the Model D10 and Model D20 I/O subsystems.
Page 62 Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
Page 63: Chapter 5. Error Code To Fru Index
Chapter 5. Error Code to FRU Index The Error Code to FRU Index lists fault symptoms and possible causes. The most likely cause is listed first. Use this index to help you decide which FRUs to replace when servicing the Model D10Model D20 I/O subsystem. See your system’s service guide for more information and a complete listing of all error codes and FRUs used by the Model D10 and Model D20 I/O subsystem.
Page 64 Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
Page 65: Chapter 6. Using The Service Processor
Chapter 6. Using the Service Processor The service processor is in the processor subsystem to which your I/O subsystem is connected and runs on its own power boundary. The service processor continually monitors hardware attributes and the environmental conditions within the system and connected I/O subsystems.
Page 66 Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
Page 67: Chapter 7. Using System Management Services
Chapter 7. Using System Management Services Use the system management services menus to view information about the processor subsystem to which the I/O subsystem is connected. For more information about the service processor, see the service guide for the attached system.
Page 68 Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
Page 69: Chapter 8. Removal And Replacement Procedures
Chapter 8. Removal and Replacement Procedures Before performing any of the removal or replacement procedures in this chapter, read the following danger and caution notices. Safety Considerations Observe the following safety precautions anytime you work with these I/O subsystems. For the I/O subsystem you are about to setup or service: v The ac power interface connector is considered the main power disconnect device.
Page 70: Handling Static-Sensitive Devices
CAUTION: This product is equipped with a three-wire power cable and plug for the user’s safety. Use this power cable with a properly grounded electrical outlet to avoid electrical shock. CAUTION: This unit has more than one power supply cord. To reduce the risk of electrical shock, disconnect two power supply cords before servicing.
Page 71: Stopping The System
Stopping the System Attention: When shutting down your system to perform service procedures, shut down all applications first and then shut down the operating system. The system power turns off and the system goes into standby mode when the operating system is shut down.
Page 72: 7311 Model D10 I/O Subsystem Removal And Replacement Procedures
7311 Model D10 I/O Subsystem Removal and Replacement Procedures The following procedures cover the removal and replacement of the 7311 Model D10 I/O Subsystem. Note: Before performing any of the removal or replacement procedures in this chapter, read the danger and caution notices on “Safety Considerations” on page 53. Model D10 FRU Replacement Procedure List Field Replaceable Unit FRU Procedure Name and Page Location...
Page 73: D10 Service Position
D10 Service Position To perform a removal or replacement procedure that requires access to the inside of the I/O subsystem, the subsystem must be removed from the rack and placed on a stable work surface. To put the drawer into the service position, do the following: 1.
Page 74: D10 Front Bezel
D10 Front Bezel Before performing the following procedure, read the “Safety Notices” on page vii. Removal To remove the front bezel, do the following: 1. Open the front rack door. 2. Simultaneously press in both bezel-release tabs. 3. Pivoting the bezel from the top, swing the top forward. 4.
Page 75: D10 Covers
D10 Covers Before performing the following procedure, read the “Safety Considerations” on page 53. Service Access Cover Removal To remove the service access cover, do the following: 1. Perform the procedure to put the I/O subsystem into the service position as described in “D10 Service Position”...
Page 76 Service Access Cover Replacement To replace the service access cover, do the following: 1. Position the cover over the rear of the I/O subsystem. 2. Align the service access cover with the I/O subsystem so that the front portion of the cover engages with the front part of the I/O subsystem chassis.
Page 77: D10 Pci Adapters
D10 PCI Adapters Most PCI adapters can be removed and replaced, or installed in the system without turning off the power to the entire system. These adapters are referred to as hot-pluggable PCI adapters . Some adapters are not hot-pluggable and power must be removed from the system for adapter removal, replacement, or installation.
Page 78 8. If you are not installing another adapter in this slot, install a blank PCI adapter cassette into the slot. 9. Connect power to the system and turn the power on. 10. Return the system to normal operations. Replacing a Non-Hot-Pluggable PCI Adapter Replace the adapter using the following procedure: Note: Because the adapter you are installing is not hot-pluggable, shut down the system and remove power before performing this procedure.
Page 79: Hot-Pluggable Pci Adapter
For additional information about taking an adapter offline or removing it from the system configuration, see the AIX System Management Guide: Operating System and Devices . Documentation for the AIX operating system is available from the IBM Eserver pSeries Information Center at http://publib16.boulder.ibm.com/pseries/en_US/infocenter/base. Select AIX documentation.
Page 80 11. The ARE YOU SURE screen displays. Press Enter to verify the information. Successful unconfigure is indicated by the OK message displayed next to the Command field at the top of the screen. 12. Press F3 to return to the PCI Hot-Plug Manager menu. 13.
Page 81 c. Hold the assembly straight on and level with the slot. d. Align the bottom edge of the PCI cassette cover with the PCI adapter guide rail on the I/O backplane. Note: If there is a cassette to the left of the one that you are installing, align the ridge on the cover with the tick in the notch of the neighboring cassette.
Page 82 28. Install the covers that you removed earlier and return the drawer to the operating position. Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
Page 83 For more information on taking the PCI adapter online, see the AIX operating system documentation. Documentation for the AIX operating system is available from the IBM Eserver pSeries Information Center at http://publib16.boulder.ibm.com/pseries/en_US/infocenter/base. Select AIX documentation. The AIX Documentation CD contains the base set of publications for the operating system, including system-management and end-user documentation.
Page 84 16. Press the Tab key until the entry field displays the remove operation and then Press the Enter key. Follow the instructions that display on the screen until you are instructed to remove the adapter. 17. When you are instructed to remove the adapter from the adapter slot, disconnect any cables that are connected to the adapter being removed.
Page 85 Installing a Hot-Pluggable PCI Adapter Note: Before installing a new adapter, ensure the device driver for the adapter is installed. Check with the system administrator if the device driver is not already installed. To install an adapter, perform the following steps: 1.
Page 86 e. Slide the cassette partially into the guide. f. Ensure that the dovetail on the top track aligns with its mating component(s) on both sides. 1 I/O Subsystem 2 PCI adapter Cassette g. When the cassette is fully inserted, prepare to activate the handle, lower the gray locking bar.
Page 87: Pci Hot-Plug Manager Access
For additional information about taking an adapter offline or removing it from the system configuration, see the AIX System Management Guide: Operating System and Devices . Documentation for the AIX operating system is available from the IBM Eserver pSeries Information Center at http://publib16.boulder.ibm.com/pseries/en_US/infocenter/base. Select AIX documentation.
Page 88 List PCI Hot-Plug Slots Provides a descriptive list of all slots that support PCI hot-plug capability. If the listing for a slot indicates it holds an “Unknown” device, select the Install/Configure Devices Added after IPL to configure the adapter in that slot. Add a PCI Hot-Plug Adapter Allows the user to add a new PCI hot-plug-capable adapter to the slot with the system turned on.
Page 89 Install/Configure Devices Added After IPL The system attempts to configure any new devices and tries to find and install any required software from a user-selected source. The add, remove, and replace functions return information to the user indicating whether the operation was successful. If additional instructions are provided on the screen, complete the recommended actions.
Page 90: Pci Adapter Or Blank Filler Removal From A Cassette Assembly
PCI Adapter or Blank Filler Removal From a Cassette Assembly This procedure is performed when preparing to install or replace an adapter or an adapter blank filler in your subsystem. Note: An adapter or an adapter blank filler must be installed into the PCI adapter cassette assembly before it is reinstalled in a system unit or a subsystem.
Page 91 2. Using two fingers, remove the bushing-lock pin from the bushing. The pin can be removed by pulling it out of the bushing with your fingernails. 1 Bushing 1 Bushing 2 Bushing-Lock Pin 2 Bushing-Lock Pin 1 Bushing-Lock Pin Chapter 8. Removal and Replacement Procedures...
Page 92 3. Remove the bushing. The bushing can be removed by pulling it out of the PCI adapter cassette assembly with your fingernails. 1 Bushing 4. Turn the PCI adapter cassette assembly over so that the top is facing away from you.
Page 93 5. Remove the bezel, as follows: a. Locate the plastic latch fingers in the top part of the cassette. 1 Top of Cassette 3 Plastic Latch Fingers 2 Bezel b. Using one hand, pinch the plastic latch fingers and with your other hand, carefully lift the top part of the bezel extension out until the tabs clear the slots in the PCI adapter cassette assembly.
Page 94 c. While holding the bezel extension out, push the plastic cover arm latch out of the bezel hook, as shown in the following illustration. This action allows the bezel to be removed. 1 Bezel Extension 2 Plastic Cover Latch in Bezel Hook d.
Page 95 e. While holding the bezel extension out, carefully slide the bezel off. You might have to work from one side and the other to loosen the bezel assembly from the cassette assembly. When the bezel is free, slide it completely off the cassette assembly and set it aside.
Page 96 As shown in the following illustration, turn over the cassette so the cover is up. Remove the cover from the cassette as follows: a. Slide the cover until it releases from the cassette assembly. Attention: The cover might be tight and difficult to slide, if you grasp the left end (handle end) of the cassette and the right end of the cover, you can use enough force to pull the cover off of the PCI adapter cassette assembly.
Page 97 c. By pulling on both sides of the gray plastic locking bar, which is located on the handle, ensure that the handle is pulled into the unlocked position. Raise the handle on the cassette linkage assembly until it locks into the up position (the blank filler or adapter moves downward).
Page 98 8. Remove the blank filler or adapter installed in the cassette linkage assembly. Note: If there is a blank filler in the cassette linkage assembly, as shipped from the manufacturer, there are two adapter arms. One adapter arm with short adapters (short adapter arm) and one adapter arm is used with long adapters (long adapter arm).
Page 99 Slide the long and short adapter arms away from the blank filler or adapter. 1 Long Adapter Arm 4 Short Adapter Arm 2 Release Tab 5 Slotted Tab 3 Release Tab Chapter 8. Removal and Replacement Procedures...
Page 100 2. Remove the adapter or blank filler from the cassette linkage assembly by rotating the bottom of the tailstock out, as shown in the following illustration. Store the adapter or blank filler in a safe place. 1 Cassette Linkage Assembly 3 Handle 2 Bottom of Tailstock 3.
Page 101 Long Adapter Removal To remove a long adapter, do the following: 1. Each adapter arm has a release tab that allows the arm to be moved away from the adapter in the cassette assembly. Use your fingernail to lift the tab to allow the arm to be moved away from the adapter.
Page 102: Replacing An Adapter In A Pci Adapter Cassette
Replacing an Adapter in a PCI Adapter Cassette This procedure is performed when preparing to install a new adapter or a blank filler in the processor subsystem or an I/O drawer. Familiarize yourself with the entire procedure before performing the following steps. Place the empty PCI adapter cassette linkage on a flat work surface in front of you.
Page 103 There are unique clips (1) for each adapter type (2): 53P5450 Clip for Gigabit Ethernet FC 2969 type 9U 44P0789 Clip for Ultra3 SCSI FC 6203 Type 4Y 44P0321 Clip for 10/100 BaseT Ethernet FC 4962 Type AF Chapter 8. Removal and Replacement Procedures...
Page 104 2. Use the following procedure to determine if you are installing a long adapter or a short adapter. If you know the length of your adapter, skip the following steps and proceed to 3 on page 89. a. Remove the adapter from its protective packaging and, if present, remove the plastic extension handle from the end of the adapter.
Page 105 c. The cassette linkage is marked to show long or short adapters similar to the adapter shown below. Check the right end of the adapter to see if it is long enough to fall into the long range. Ensure that the corner on the left end of the adapter is still aligned into the top adapter retaining clip and determine the length of the adapter.
Page 106: Short Adapter Or Blank Filler Installation
Adapter Installation” on page 106. Handle Lock Short Adapter or Blank Filler Installation Use the following procedure to install a short adapter or blank filler. 1. Install the adapter or blank filler by doing the following: a. Place the adapter or blank filler into the cassette so that the upper left corner of the adapter engages the adjustable top adapter retaining clip as shown in Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
Page 107 the following figure. Cassette Linkage Assembly Bottom of Tailstock Handle Retaining Clip b. Rotate the adapter so that the adapter engages the slot in the bottom retaining clip and the top corner of the adapter is seated into the adjustable adapter top retaining clip.
Page 108 adapter is seated into the slot on the bottom retaining clip. Adapter Slot Bottom Retaining Clip c. Slide the short adapter retaining arm toward the adapter or blank filler on the cassette linkage rail. 1) If the short adapter retaining arm has been removed from the cassette linkage rail, install the short adapter retaining arm and then slide the arm Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
Page 109 until it contacts the adapter or blank filler as shown in the following figure. d. Ensure that the adjustable top adapter retainer clip catches the corner of the adapter as shown in the following figures. Short Adapter Top Retaining Clip e.
Page 110 Note: It might be necessary to apply pressure to engage and hold the bottom of the adapter. Lower Short Adapter Arm Clip f. To hold the top of the adapter, slide the top adjustable adapter retaining clip on the retaining arm down. Ensure that the bottom edge of the adapter is held by the lower part of the adapter retaining arm.
Page 111 g. Press the lock on the handle and rotate the adapter handle until it is in the down position (adapter or blank filler moves up into the cassette assembly). Handle Lock Ensure the right end of the cassette linkage rail moves up into the cassette as shown below.
Page 112 h. Position the adapter and cassette assembly with the handle on the left (in the down position) and the top facing away from you. Cassette Top Handle i. Install the cover on the cassette assembly: 1) Place the cassette cover on the cassette assembly as shown below, and slide the cover toward the handle until the hole in the cover aligns with the Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
Page 113 hole in the cassette assembly. Handle Holes Aligned Install the bezel assembly using the following procedure. Chapter 8. Removal and Replacement Procedures...
Page 114 1) Carefully slide the bezel onto the cassette assembly. Bezel Align and insert the cover arm latch in the hooked notch in the bezel. Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
Page 115 3) Align the top of the bezel assembly into the grooves on the top of the cassette assembly and then push the bezel onto the cassette linkage until the tab on the top of the bezel is seated in the recess of the cassette assembly.
Page 116 k. Check for the following: 1) Ensure that extension arm engages the pins on the cassette. You should be able to see the pins through the holes in the arm. The bezel tab should be seated as shown in the following figure. 2) Ensure the cover arm latch is completely pressed into the hooked slot on the bezel as shown.
Page 117 3) Turn the cassette assembly over so the cover is up and check the cover latch to ensure it is holding the bezel to the cover as shown. Cover Latch l. Position the adapter with the cover side up. Ensure the holes are aligned and insert the bushing as shown.
Page 118 m. Insert the bushing lock pin into the hole in the bushing and push it in until it seats. Bushing Lock Pin n. By pulling on both sides, ensure the grey plastic locking bar on the handle is pulled into the unlocked position. Raise the handle on the cassette linkage until Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
Page 119 it locks into the up position (the blank filler or adapter moves downward). o. To install the metal EMC shield on the adapter bracket: 1) Ensure that the shield slides up inside the top of the cassette. Chapter 8. Removal and Replacement Procedures...
Page 120 2) The metal shield has clips that slide over the top of the tailstock. Ensure that these clips are holding the EMC bracket to the tailstock. Top of Tailstock p. Press the lock on the handle and rotate the adapter handle until the handle is in the down position (adapter or blank filler moves up into the cassette assembly).
Page 121 color indicator to allow the orange to be visible. If the adapter is not hot-swappable, then the blue color should show. Orange for Blue for Not Hot-Swappable Hot-Swappable r. The adapter is ready to be installed into a system or an I/O drawer. Refer to your system documentation for more information.
Page 122: Long Adapter Installation
Long Adapter Installation Use the following procedure to install a long adapter. Note: Ensure that both the long and short adapter retaining arms are removed from the cassette linkage. See 1a on page 82 to remove the arms before continuing below.
Page 123 adapter is seated into the slot on the bottom retaining clip. Adapter Slot Bottom Retaining Clip c. Install the long adapter retaining arm onto the cassette linkage rail as shown in the following figure, and slide it toward the adapter. Long Adapter Retaining Arm Cassette Linkage Assembly Top Adapter...
Page 124 d. Ensure that the adjustable top adapter retaining clip catches the corner of the adapter as shown in the following figures. Long Arm Adjustable Retaining Clip e. Ensure that the bottom edge of the adapter is held by the lower part of the adapter retaining arm.
Page 125 f. To hold the top of the adapter, slide the top adjustable adapter retaining clip on the retaining arm down. Long Adapter Retaining Arm g. Press the lock on the handle and rotate the adapter handle until the it is in the down position (adapter or blank filler moves up into the cassette assembly).
Page 126 Ensure the right end of the cassette linkage rail moves up into the cassette as shown below. Right End of Cassette Linkage h. Position the adapter and cassette assembly with the handle on the left (in the down position) and the top facing away from you. Top of Cassette Handle i.
Page 127 hole in the cassette assembly. Handle Holes Aligned Install the bezel assembly using the following procedure. Chapter 8. Removal and Replacement Procedures...
Page 128 1) Carefully slide the bezel onto the cassette assembly. Bezel Align and insert the cover arm latch in the hooked notch in the bezel. Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
Page 129 3) Align the top of the bezel assembly into the grooves on the top of the cassette assembly and then push the bezel onto the cassette linkage until the tab on the top of the bezel is seated in the recess of the cassette assembly.
Page 130 k. Check for the following: Ensure that extension arm engages the pins on the cassette. You should be able to see the pins through the holes in the arm. The bezel tab should be seated as shown in the following figure. 2) Ensure the cover arm latch is completely pressed into the hooked slot on the bezel as shown.
Page 131 3) Turn the cassette assembly over so the cover is up and check the cover latch to ensure it is holding the bezel to the cover as shown. Cover Latch l. Position the adapter with the cover side up. Ensure the holes are aligned and insert the bushing as shown.
Page 132 m. Insert the bushing lock pin into the hole in the bushing and push it in until it seats. Bushing Lock Pin n. By pulling on both sides, ensure the grey plastic locking bar on the handle is pulled into the unlocked position. Raise the handle on the cassette linkage until Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
Page 133 it locks into the up position (the blank filler or adapter moves downward). o. To install the metal EMC shield on the adapter bracket: 1) Ensure that the shield slides up inside the top of the cassette. Chapter 8. Removal and Replacement Procedures...
Page 134 2) The metal shield has clips that slide over the top of the tailstock. Ensure that these clips are holding the EMC bracket to the tailstock. Top of Tailstock p. Press the lock on the handle and rotate the adapter handle until the handle is in the down position (adapter or blank filler moves up into the cassette assembly).
Page 135 color indicator to allow the orange to be visible. If the adapter is not hot-swappable, then the blue color should show. Orange for Blue for Not Hot-Swappable Hot-Swappable r. The adapter is ready to be installed into a system or an I/O drawer. Refer to you system documentation for more information.
Page 136: D10 Fan
D10 Fan Before performing the following procedure, read “Safety Considerations” on page 53. Hot-Swap Fan Assembly Removal To remove a hot-swap fan, do the following: 1. Locate the cooling fan assembly on the front of the I/O subsystem. 2. Unscrew the thumbscrew that holds the fan into the I/O subsystem. 3.
Page 137: D10 Rio Cable
D10 RIO Cable Removal 1. Turn off the power to the system. 2. Release the RIO cable retainers. 3. Disconnect the RIO cable. Replacement Replace in reverse order. D10 RIO Bus Adapter Removal Before performing the following procedure, read the “Safety Considerations” on page 53.
Page 138: D10 I/O Backplane Assembly
D10 I/O Backplane Assembly Before performing the following procedure, read the “Safety Considerations” on page 53. Note: The I/O backplane and the SPCN riser card are replaced as a pair. Removal 1. Turn off the system power. 2. Perform the procedure to put the I/O subsystem into the service position as described in “D10 Service Position”...
Page 139: D10 Power Supply
Note: The I/O backplane and the SPCN connector card are replaced as a pair. 6. Reinstall the RIO bus adapter card. (See “D10 RIO Bus Adapter” on page 121). 7. Reinstall the power supplies. (See “D10 Power Supply”). 8. Reinstall the cover. (See “D10 Covers” on page 59). 9.
Page 140: 7311 Model D20 I/O Subsystem Removal And Replacement Procedures
7311 Model D20 I/O Subsystem Removal and Replacement Procedures Notes: 1. All of the parts in the 7311 Model D20 I/O Subsystem can be replaced with the subsystem installed in a rack. The power supplies, blowers, disk drives and PCI adapters are hot-plug.
Page 141: D20 Service Position
D20 Service Position Attention: When placing your Model D20 subsystem into the service position, it is essential that all stability plates are firmly in position to prevent the rack from toppling. Ensure that only one system drawer is in the service position at a time. Before doing any service actions inside your Model D20 subsystem, put the Model D20 subsystem into the service position.
Page 142: D20 Operating Position
1 Model D20 Subsystem 4 Stabilizing Bar 2 19 Inch Rack 5 Front Rack Door 3 Extension Rail Safety Release 6 System Drawer Release Latch Latch After completing the service actions, return the Model D20 subsystem to the operating position. D20 Operating Position To return your Model D20 subsystem to the operating position, do the following: 1.
Page 143: D20 Service Access Cover
D20 Service Access Cover Before performing the following procedure, read the “Safety Considerations” on page 53. Opening the Service Access Cover To open the service access cover, do the following: 1. Open the front rack door and place the Model D20 subsystem into the service position as described in “D20 Service Position”...
Page 144 Service Access Cover Removal If you need to remove the service access cover from the subsystem, do the following: 1. Open the cover as described in the above procedure. 2. Remove the four retaining screws that secure the cover hinge to the chassis. 3.
Page 145: D20 Front Bezel
D20 Front Bezel Before performing the following procedure, read the “Safety Considerations” on page 53. Front Bezel Removal To remove the front bezel, do the following: 1. Open the front rack door. If necessary, place the Model D20 subsystem into the service position as described in “D20 Service Position”...
Page 146 Front Bezel Replacement To replace the front bezel, do the following: 1. Open the front rack door. If necessary, put the Model D20 subsystem into the service position as described in “D20 Service Position” on page 125. 2. Insert the two tabs located on the bottom edge of the bezel into their locking slots, located on the chassis.
Page 147: D20 Operator Panel
D20 Operator Panel Before performing the following procedure, read “Safety Considerations” on page 53. 1 Power LED (Green) 2 Attention LED (Amber) 3 Operator Panel 4 Snap Buttons Operator Panel Removal To remove the operator panel from the subsystem, do the following: 1.
Page 148 1 Rack Front Door 4 Snap Buttons 2 Model D20 5 Front Bezel 3 Operator Panel Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
Page 149 Operator Panel Replacement To replace the operator panel, do the following: 1. Connect the power/signal cable connector to the back of the operator panel. 2. Carefully slide the operator panel back into the system bay. 3. Ensure that the two snap buttons are in the unlocked position. Note: Snap buttons are in the unlocked position when the button component is pulled back as far as possible.
Page 150: D20 Blowers
D20 Blowers Before performing the following procedure, read “Safety Considerations” on page 53. Each cooling blower assembly has a green LED and an amber LED. The green LED indicates when the cooling blower is receiving power. A blinking amber LED indicates when the cooling blower needs attention from a potential cooling problem.
Page 151 1 Green LED 4 Blower Connector 2 Amber LED 5 Hot-Plug Blower Assembly 3 Snap Button 6 Docking Connector Chapter 8. Removal and Replacement Procedures...
Page 152 Hot-Swap Blower Replacement Note: If a blower assembly is being replaced for a redundant failure, after the service repair action is completed, ask the customer to check the crontab file for any power/cooling warning messages. When a power or cooling error is encountered, AIX adds an entry to the crontab file to ″wall″...
Page 153: D20 Cooling Blowers Cable
D20 Cooling Blowers Cable This procedure must be performed with the power turned off. Cooling Blower Cable Removal To remove the cooling blower cable do the following: 1. Open the rack front door. 2. Shut down the system as described in “Stopping the System” on page 55. 3.
Page 154 1 Cooling Blowers 5 Connector Retaining Ears 2 Cable Ties 6 Blower Docking Connector 3 Tab Retaining Clip 7 Model D20 4 Connector Release Tab Cooling Blower Cable Replacement Replace in reverse order. Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
Page 155: D20 Rio Bus Adapter Assembly
D20 RIO Bus Adapter Assembly Before performing this procedure, read “Safety Considerations” on page 53. In the following RIO bus adapter removal and replacement procedures, the RIO bus adapter assembly will be referred to as the RIO adapter. RIO Bus Adapter Removal To remove the RIO adapter from the subsystem, do the following: 1.
Page 156 1 RIO Bus Adapter Release 4 Service Access Cover Handle 2 RIO Bus Adapter Release 5 Model D20 Subsystem Latch 3 RIO Bus Adapter Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
Page 157 RIO Bus Adapter Replacement To replace the RIO bus adapter, do the following: 1. Grasp the two RIO adapter release handles. 2. Pivot both handles upward to 90 degrees, ensuring that the handles are perpendicular to the RIO adapter. The handle cams have now been placed into the correct position to assist you when seating the RIO adapter into its docking connector.
Page 158: D20 Pci Adapters
For additional information about taking an adapter offline or removing it from the system configuration, see the AIX System Management Guide: Operating System and Devices . Documentation for the AIX operating system is available from the IBM Eserver pSeries Information Center at http://publib16.boulder.ibm.com/pseries/en_US/infocenter/base. Select AIX documentation.
Page 159 To access the hot-plug menus, do the following: 1. Log in as root user. 2. At the command line, type smitty. 3. Select Devices. 4. Select PCI Hot Plug Manager and press Enter. 5. The PCI Hot-Plug Manager menu displays. Return to the procedure that directed you here.
Page 160 Unconfigure a Device Allows the user to put an existing PCI adapter into the Defined state if the device is no longer in use. This step must be completed successfully before starting any removal or replacement operation. If this step fails, the customer must take action to release the device. Configure a Defined Device Allows a new PCI adapter to be configured into the system if software support is already available for the adapter.
Page 161 Non-Hot-Pluggable PCI Adapter Removal To remove a PCI adapter, do the following: 1. Open the front and rear rack doors and place the subsystem into the service position as described in “D20 Service Position” on page 125. 2. Shut down the system as described in “Stopping the System” on page 55. 3.
Page 162 8. Rotate the adapter retainer clip counterclockwise, as shown in the following illustration. 9. Lift the adapter retaining seat resting on the adapter retention bracket. 10. Carefully grasp the PCI adapter by its top edge or upper corners, and remove it from the system.
Page 163 1 Model D20 2 Service Access Cover 3 Retainer Clip 4 Retainer Seat 5 PCI Adapter Adding or Replacing a Non-Hot-Pluggable PCI Adapter To add or install an adapter, do the following: 1. Open the front and rear rack doors and place the system into the service position as described in “D20 Service Position”...
Page 164 4. Open the service access cover as described in “Service Access Cover Removal” on page 128. 5. Refer to the PCI Adapter Placement Reference for information regarding slot restrictions for adapters that can be used in this subsystem. 6. If necessary, remove the adapter expansion slot shield. 7.
Page 165 For additional information about taking an adapter offline or removing it from the system configuration, see the AIX System Management Guide: Operating System and Devices . Documentation for the AIX operating system is available from the IBM Eserver pSeries Information Center at http://publib16.boulder.ibm.com/pseries/en_US/infocenter/base. Select AIX documentation.
Page 166 14. Select Replace/Remove a PCI Hot-Plug Adapter and press Enter. The Replace/Remove a PCI Hot-Plug Adapter menu displays. Note: If the PCI Hot-Plug Adapter menu indicates that the slot for the just replaced adapter is reading empty, do the following: a.
Page 167 18. Before handling any card, board, or memory DIMM, be sure to use your electrostatic discharge strap to minimize static-electric discharge. Refer to “Handling Static-Sensitive Devices” on page 54. 1 Hot-Plug PCI Adapters 2 Service Access Cover 3 Model D20 Subsystem Chapter 8.
Page 168 19. Turn the retainer clip and lift the adapter retaining seat off the adapter. 1 Model D20 2 Service Access Cover 3 Retainer Clip 4 Retainer Seat 5 PCI Adapter 20. Carefully grasp the adapter by the edges and pull it straight out from the PCI riser card.
Page 169 For additional information about taking an adapter offline or removing it from the system configuration, see the AIX System Management Guide: Operating System and Devices . Documentation for the AIX operating system is available from the IBM Eserver pSeries Information Center at http://publib16.boulder.ibm.com/pseries/en_US/infocenter/base. Select AIX documentation.
Page 170 To replace a hot-plug PCI adapter, do the following: 1. Open the front and rear rack doors and place the system into the service position as described in “D20 Service Position” on page 125. 2. Remove the service access cover as described in “Service Access Cover Removal”...
Page 171 i. Return to the error code or procedure that sent you here, if the ″List PCI Hot-Plug Slots″ menu indicates that the slot for the just replaced or reseated adapter is empty. 15. Select F3 to cancel. 16. Select Replace/Remove a PCI Hot-Plug Adapter, then press Enter. The ″Replace/Remove a PCI Hot-Plug Adapter menu displays.
Page 172 1 Model D20 2 Service Access Cover 3 Retainer Clip 4 Retainer Seat 5 PCI Adapter 23. Place the adapter, component-side up, on a flat, static-protective surface. 24. Set any jumpers or switches as instructed by the adapter manufacturer. 25. Replace the adapter into the adapter slot. Carefully grasp the adapter by the edges and align the adapter in the slot guides.
Page 173 If you have added, removed, or replaced any adapters, run the diag -a command. If the system responds with a menu or prompt, follow the instructions to complete the device configuration. Documentation for the AIX operating system is available from the IBM Eserver pSeries Information Center at http://publib16.boulder.ibm.com/pseries/en_US/infocenter/base. Select AIX documentation.
Page 174 6. If necessary, remove the adapter from the antistatic package. Attention: Avoid touching the components and gold-edge connectors on the adapter. 7. Place the adapter, component-side up, on a flat, static-protective surface. 8. Set any jumpers or switches as described by the adapter’s manufacturer. 9.
Page 175 14. Follow the instructions on the screen to install the adapter until the LED for the specified PCI slot is set to the Action state. See “Model D20 PCI-X Slots” on page 16. 15. When you are instructed to install the adapter in the adapter slot, carefully grasp the adapter by the edges and align the adapter in the slot guides.
Page 176: D20 Hot-Plug Disk Drives
2. Before a disk can be removed from a volume group, all data must be backed up and the data removed from the disk to be replaced. Use AIX Logical Volume Manager to perform this task. Documentation for the AIX operating system is available from the IBM Eserver pSeries Information Center at http://publib16.boulder.ibm.com/pseries/en_US/infocenter/base. Select AIX documentation.
Page 177 13. See the AIX System Management Guide: Operating System and Devices to finish the drive configuration. Documentation for the AIX operating system is available from the IBM Eserver pSeries Information Center at http://publib16.boulder.ibm.com/pseries/en_US/infocenter/base. Select AIX documentation. The AIX Documentation CD contains the base set of publications for the operating system, including system-management and end-user documentation.
Page 178 Hot-Plug Disk Drive Removal Attention: Before you perform the following procedure, ensure that the customer has taken appropriate actions to back up the data for the drive you are removing, and that the drive has been removed from the configuration. Physically removing a hot-plug drive from the system before it has been removed from the system configuration can cause unrecoverable data corruption.
Page 179 1 Rack Front Door 3 Disk Drive Release Handle 2 Model D20 4 Front Bezel Chapter 8. Removal and Replacement Procedures...
Page 180 Hot-Plug Disk Drive Replacement Attention: Before you perform these procedures, ensure that the customer has taken appropriate actions to back up the data for the drive you are removing, and that the drive has been removed from the configuration. Physically removing a hot-plug drive from the system before it has been removed from the system configuration can cause unrecoverable data corruption.
Page 181: D20 Disk Drive Cage
D20 Disk Drive Cage Before performing the following procedure, read “Safety Considerations” on page 53. Disk Drive Cage Removal To remove the disk drive cage, do the following: 1. Open the rack front door. 2. Shut down the system as described in “Stopping the System” on page 55. 3.
Page 182 1 Model D20 5 Retaining Screws (Quantity 8) 2 Disk Drive Cage 6 Light Pipes 3 Disk Drives 7 Light Pipe Support Bracket 4 Front Bezel Disk Drive Cage Replacement To replace the disk drive cage, go the following: 1. Insert the disk drive cage assembly into the subsystem. 2.
Page 183: D20 Disk Drive Backplane
D20 Disk Drive Backplane Before performing the following procedure, read “Safety Considerations” on page 53. Disk Drive Backplane Removal To remove the disk drive backplane, do the following: 1. Remove all hot-plug disk drives as described in “Hot-Plug Disk Drive Removal” on page 162.
Page 184 Disk Drive Backplane Replacement To replace the disk drive backplane, do the following: 1. Reconnect the power/signal cable to the connector located on the top edge of the disk drive backplane. 2. Grasp a bottom edge of one of the connectors located on the disk drive backplane and insert the backplane into the disk drive bay.
Page 185: D20 Power Supplies
D20 Power Supplies DANGER Do not attempt to open the covers of the power supply. Power supplies are not serviceable and are to be replaced as a unit. The Model D20 subsystem has power supplies that have hot-swap capabilities. To use this feature, you must have two power supplies in place.
Page 186 7. Carefully remove the power supply from the subsystem. 1 Power Supplies 4 Green DC Good LED 2 Green Power LED 5 Power Supply Filler 3 Amber Fault/Identify LED 6 Model D20 Subsystem Note: During normal operation, each power-supply bay must have either a power supply or filler panel installed for proper cooling.
Page 187 Power Supply Replacement To replace a power supply, do the following: 1. Ensure the handles are in the unlocked position and perpendicular to the power supply. 2. Carefully insert the new power supply into the power supply bay. 3. Press the power supply onto the docking connectors. 4.
Page 188: D20 Power Supply Bulkhead
D20 Power Supply Bulkhead Before performing the following procedure, read the “Safety Considerations” on page 53. Power Supply Bulkhead Removal To remove the power supply bulkhead, do the following: 1. Open the rack front door. 2. Shut down the system as described in “Stopping the System” on page 55. 3.
Page 189 1 Power Supply Filler 5 PCI-X Adapters 2 Power Supply Bulkhead 6 Model D20 3 PCI Dividers 7 Power Supplies 4 RIO Bus Adapter Chapter 8. Removal and Replacement Procedures...
Page 190 Power Supply Bulkhead Replacement To replace the power supply bulkhead, do the following: 1. Before handling any card, board, or memory DIMM, be sure to use your electrostatic discharge strap to minimize static-electric discharge. Refer to “Handling Static-Sensitive Devices” on page 54. 2.
Page 191: D20 I/O Backplane
D20 I/O Backplane Before performing the following procedure, read the “Safety Considerations” on page 53. I/O Backplane Removal To remove the I/O backplane from the subsystem, do the following: 1. Open the rack front door. 2. Shut down the system as described in “Stopping the System” on page 55. 3.
Page 192 17. Remove the I/O backplane by lifting the board straight up and out of the subsystem. 18. Locate the VPD module. See “Model D20 I/O Backplane Locations” on page 23 for the VPD module location. 19. Note the location of pin 1 on the VPD module. 20.
Page 193 I/O Backplane Replacement To replace the I/O backplane, do the following: 1. Before handling any card, board, or memory DIMM, be sure to use your electrostatic discharge strap to minimize static-electric discharge. Refer to “Handling Static-Sensitive Devices” on page 54. 2.
Page 194 14. Replace all of the previously removed PCI adapters as described in “Adding or Replacing a Non-Hot-Pluggable PCI Adapter” on page 147. Note: Alternately reinstall the PCI dividers, when reinstalling the PCI adapters. 15. Reconnect all PCI adapter cables to their respective adapters. 16.
Page 195: Chapter 9. Parts Information
Chapter 9. Parts Information This chapter contains parts information for the 7311 Model D10 and Model D20 I/O drawers.
Page 196: 7311 Model D10 I/O Subsystem
7311 Model D10 I/O Subsystem This section lists part numbers for the 7311 Model D10 I/O Subsystem. This I/O subsystem is used in conjunction with a system unit. Depending on your configuration, the quantities of parts listed may increase by the actual number of I/O subsystems connected to the system unit.
Page 197 Index Part Number Units Per Description Assy 00P2752 Bracket, Bulkhead 09P4656 Tray, cable 09P5417 Cable, fan 09P3128 Guide, mounting 1624749 Screw, guide mounting ******* See index number 9 1621829 Screw, tray mounting 1624743 Screw, backplane mounting 09P5921 I/O backplane assembly (includes SPCN connector card ) 1621829 Screw, tailstock cover mounting...
Page 198: D10 Power And Cooling
D10 Power and Cooling Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
Page 199 Index Part Number Units Per Description Assy 00P2753 Cover, access 09P4778 Front bezel, black 09P5159 Front bezel, white 1624743 Screw, guide mounting 00P2750 Guide, adapter cassette top 44P0239 Empty PCI adapter cassette kit 00P3842 PCI adapter cassette blank filler, long 00P3843 PCI adapter cassette blank filler, short 53P5450...
Page 200: D10 Spcn, Rio, And Rack Beacon Cables
D10 SPCN, RIO, and Rack Beacon Cables Index Part Number Units Per Description Assy 53P2231 Up to 12 Rack beacon junction box, 7-port mini connector (4693) 53P2237 Up to 12 Rack beacon connector cable, subsystem to junction box, 4-pin std to 4-pin mini connector, 3 meter (4691) 07H6655 As needed...
Page 201: D10 Rack Mounting Enclosure
D10 Rack Mounting Enclosure Index Part Number Units Per Description Assy 09P4746 Two position I/O subsystem mounting assembly 03N3845 Left rail 03N3847 Right rail 00P2402 Cable support bracket 09P4911 Mounting bracket 09P4912 Rear filler for empty I/O subsystem space in mounting assembly Chapter 9.
Page 202: Model D20 I/O Subsystem
Model D20 I/O Subsystem This section lists part numbers for the 7311 Model D20 I/O Subsystem. This I/O subsystem is used in conjunction with a system unit. Depending on your configuration, the quantities of parts listed may increase by the actual number of I/O subsystems connected to the system unit.
Page 203 Index Part Units Per Description Number Assy 53P0416 DASD cable 53P0419 Blower cable 53P0414 Operator panel cable 53P0220 Chassis assembly 44H7366 Mounting screw, stiffener 53P3472 I/O Backplane Chapter 9. Parts Information...
Page 204: D20 Pci Slots
D20 PCI Slots Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
Page 205 Index Part Number Units Per Description Assy See Note 7 (maximum PCI adapter quantity) 53P0248 Power bulkhead 44H7366 Screw, power bulkhead mounting 44H7366 Screw, PCI plate mounting 53P0249 PCI adapter headstock plate 53P2728 PCI dividers 53P2729 PCI dividers Note: See RS/6000 Eserver pSeries Diagnostic Information for Multiple Bus Systems for part numbers.
Page 206: D20 Power, Rio
D20 Power, RIO Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
Page 207 Index Part Number Units Per Description Assy 53P4832 2 (maximum Power supply quantity) 53P3800 RIO bus adapter 53P2690 Cable bracket, SCSI 44H7366 Screw, SCSI cable 53P0639 RIO G cable bracket 44H7366 Screw, RIO G cable bracket 53P0417 Configuration SCSI bus cable dependent 53P0418 Configuration...
Page 208: D20 Operator Panel
D20 Operator Panel Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
Page 209 Index Part Number Units Per Description Assy 53P0257 Disk Drive Backplane 53P0321 Screw, disk drive backplane mounting 53P0330 Operator panel 53P0275 Processor cover 44H7366 Screw, cover mounting Chapter 9. Parts Information...
Page 210: D20 Fans And Disk Drives
D20 Fans and Disk Drives Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
Page 211 Index Part Number Units Per Description Assy 53P0262 Blower Model D20 53P0250 Disk Drive cage 12 pack 53P0319 Screw, DASD cage mounting Disk Drives 53P0234 Screw, filler plate mounting 44H7366 1 (optional) Disk Drive filler plate Chapter 9. Parts Information...
Page 212: D20 Covers And Brackets
D20 Covers and Brackets Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
Page 213: D20 Rio, Spcn, And Rack Beacon Cables
Index Part Number Units Per Description Assy 53P1457 Front bezel 44H7366 Screw, latch bracket 53P2572 Latch bracket assembly left 53P0295 Cable arm bracket 44H7366 Screw, cable arm bracket 53P2573 Latch bracket assembly right D20 RIO, SPCN, and Rack Beacon Cables Index Part Number Units Per...
Page 214: Power Cables
Power Cables Index Part Number Country or Region 1838574 Bahamas, Barbados, Bolivia, Brazil, Canada, Costa Rica, Dominican Republic, El Salvador, Ecuador, Guatemala, Guyana, Haiti, Honduras, Jamaica, Japan, Netherlands Antilles, Panama, Peru, Philippines, Taiwan, Thailand, Trinidad, Tobago, U.S.A. (except Chicago), Venezuela 86G7648 Bahamas, Barbados, Bermuda, Bolivia, Brazil, Canada, Cayman Islands, Colombia, Costa Rica, Dominican Republic, Ecuador, El...
Page 215 Index Part Number Country or Region 14F0051 Liechtenstein, Switzerland 14F0069 Chile, Ethiopia, Italy 14F0087 Israel 6952291 Paraguay, Colombia, Uruguay 42F6841 AC Power Cable, (Power distribution bus to AC power supply, Model 6C4 only) Chapter 9. Parts Information...
Page 216 Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
Page 217: Appendix A. Environmental Notices
Recycling facilities may not be available in your area. For information on disposal of batteries, contact your local waste disposal facility. In the United States, IBM has established a collection process for reuse, recycling, or proper disposal of used IBM sealed lead acid, nickel cadmium, nickel metal hydride, and other battery packs from IBM Equipment.
Page 218: Pseries 7311 Model D20 Declared Acoustical Noise Emissions
Four D10 I/O subsystems Notes: 1. Noise levels cited are for the typical configuration (A-Frame: Bulk Power, CEC cage, battery option, media drawer, and two I/O drawers). 2. The 0.6-B (6-dB) reduction in noise emission levels with the acoustical rear door corresponds to a factor of 4 reduction.
Page 219: Appendix B. Notices
Appendix B. Notices This information was developed for products and services offered in the U.S.A. The manufacturer may not offer the products, services, or features discussed in this document in other countries. Consult the manufacturer’s representative for information on the products and services currently available in your area. Any reference to the manufacturer’s product, program, or service is not intended to state or imply that only that product, program, or service may be used.
Page 220 Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
Page 221: Index
Index D10 locations (continued) D10 I/O subsystem, rear 11 accessibility xiii I/O backplane 12 accessing information xiii model D10 15 acoustical PHB 13 noise D10 replacement procedure list 56 emissions 201 D20 location code table 34 adapter and filler removal and replacement D10 74 D20 location codes 33 adapter, PCI removal and replacement, D10 61 D20 locations 19...
Page 222 features, subsystem (continued) locations, D10 10 ports, serial 6 locations, D20 19 power 4 long adapter removal, D10 85 features, system 16 cooling 19 MAP rules 43 disk drives 18 operator panel 16 PCI-X slots 16 noise emissions ports, input/output 19 acoustical 201 ports, serial 19 non-hot-pluggable PCI adapter, removal D20 145...
Page 223 power supply locations 21 removal and replacement procedures (continued) power supply removal D20 169 safety considerations 53 power supply removal, D10 123 service position 125 power supply replacement, D10 123 short adapter and filler, D10 82 power supply, hot-swap replacement, D20 171 starting the system 55 power supply, removal and replacement, D10 123 stopping the system 55...
Page 224 RIO bus adapter, D20 139 RIO cable removal D10 121 RIO cable replacement, D10 121 RIO cable, removal and replacement D10 121 RIO cables 6 RIO, parts 190 safety considerations 53 safety notices vii SCSI IDs 25 Self-Test, Power-On 36 serial port configurations 19 service access cover removal, D10 59 service access cover removal, D20 128...
Page 225 Thank you for your responses. May we contact you? h Yes h No When you send comments to IBM, you grant IBM a nonexclusive right to use or distribute your comments in any way it believes appropriate without incurring any obligation to you. Name...
Page 226 Readers’ Comments — We’d Like to Hear from You Cut or Fold Along Line SA38-0627-00 Fold and Tape Please do not staple Fold and Tape _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ NO POSTAGE NECESSARY IF MAILED IN THE...
Page 228 Printed in U.S.A. December 2002 SA38-0627-00...

This manual is also suitable for:

Pseries 7311 d20

IBM eserver pSeries 7311 D10 Service Manual

Safety Notices

Data Integrity and Verification

About this Book

Chapter 1. Reference Information

Chapter 2. Diagnostics Overview

Chapter 3. Maintenance Analysis Procedures (Maps)

Chapter 4. Checkpoints

Chapter 5. Error Code to FRU Index

Chapter 6. Using the Service Processor

Chapter 7. Using System Management Services

Chapter 8. Removal and Replacement Procedures

Chapter 9. Parts Information

Appendix A. Environmental Notices

Appendix B. Notices

Index

Quick Links

Related Manuals for IBM eserver pSeries 7311 D10

Summary of Contents for IBM eserver pSeries 7311 D10

This manual is also suitable for:

Table of Contents