hit counter script
Sony HCD-MD313 Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. Stereo System
  5. HCD-MD313
  6. Service manual
Sony HCD-MD313 Service Manual

Sony HCD-MD313 Service Manual

Mini hi-fi component system
Hide thumbs Also See for HCD-MD313:
Table of Contents

Advertisement

Quick Links

See also: Service Manual
SERVICE MANUAL
Hcd-Md313 is the amplifier, CD, MD and
tuner section in DHC-MD313.
US and foreign patents licensed from Dolby
Laboratories Licensing Corporation.
Amplifier section
European model:
DIN power output
25 + 25 watts (6 ohms at 1 kHz, DIN)
Continuous RMS power output
30+30 watts
(6 ohms at 1 kHz, 10% THD)
Music power output
50 +50 watts
Other models:
Peak music power output 400 watts
Continuous RMS power output
25 + 25 watts (6 ohms at 1 kHz, 10% THD)
Inputs
TAPE IN (phono jacks):
voltage 250 mV/125 mV, impedance 47 kilohms
Outputs
TAPE OUT (phono jacks):
voltage 250 mV impedance 1 kilohms
PHONES (stereo phone jack):
accepts headphones of 8 ohms or more.
SPEAKER:
accepts impedance of 6 to 16 ohms.
CD player section
System
Compact disc and digital audio system
Laser
Semiconductor laser (λ = 780 nm)
Emission duration: continuous
Laser output
Max. 44.6 µW*
*This output is the value measured at a distance
of 200 mm from the objective lens surface on the
Optical Pick-up Block with a 7 mm aperture.
Frequency response
2 Hz – 20 kHz
MICROFILM
HCD-MD313
Model Name Using Similar Mechanism
CD Mechanism Type
CD
Section
Base Unit Name
Optical Pick-up Name
Model Name Using Similar Mechanism
MD
MD Mechanism Type
Section
Optical Pick-up Name

SPECIFICATIONS

MD deck section
System
Laser
Laser output
Recording time
Sampling frequency
Frequency response
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range
Aerial
Aerial terminals
Intermediate frequency
MINI Hi-Fi COMPONENT SYSTEM
AEP Model
UK Model
E Model
HCD-T1
CDM13C-5BD19
BU-5BD19
KSS-213B/K-N
MDS-MX1
MDM-3D
KMS-260A/J1N
MiniDisc digital audio system
Semiconductor laser (λ = 780 nm)
Emission duration: continuous
Max. 44.6 µW*
*This output is the value measured at a distance
of 200 mm from the objective lens surface on the
Optical Pick-up Block with a 7 mm aperture.
74 minutes max. (using MDW-74)
44.1 kHz
5 Hz to 20 kHz
87.5 – 108.0 MHz (50 kHz step)
FM lead aerial
75 ohms unbalanced
10.7 MHz
– Continued on next page –

Advertisement

Table of Contents
loading

Related Manuals for Sony HCD-MD313

Summary of Contents for Sony HCD-MD313

  • Page 1 HCD-MD313 SERVICE MANUAL AEP Model UK Model E Model HCD-MD313 is the amplifier, CD, MD and tuner section in DHC-MD313. US and foreign patents licensed from Dolby Model Name Using Similar Mechanism HCD-T1 Laboratories Licensing Corporation. CD Mechanism Type CDM13C-5BD19...

  • Page 2: Table Of Contents

    Supplied accessories: Remote RM-MD313 (1) 6-3. Schematic Diagram — CD Section — ......35 Sony batteries (2) 6-4. Printed Wiring Boards — MD Section — ....... 39 AM loop aerial (1) 6-5. Schematic Diagram — MD Section — ......41...

  • Page 3: Servicing Notes

    LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY.
  • Page 4 DISC TABLE GETTING OUT PROCEDURE ON FLUORESCENT INDICATOR TUBE/BUTTONS/JOG/ THE POWER SUPPLY IS OFF LEDs CHECK MODE 1. Insert the tweezers to a hole on bottom of the chassis as shown 1. Press two buttons PLAY MODE and p (MD) simulatneously a figure, then tern fully it toward direction 2.

  • Page 5: General

    SECTION 2 GENERAL LOCATION OF CNTROLS POWER button – Front Panel – MD disk slot § (MD) button ^ (MD) button p (MD) button VOLUME control knob ^ (CD) button p (CD) button FUNCTION button !º Fluorescent indicator tube !¡ !º...
  • Page 6 – Remote controller – POWER button DBFB button MUSIC MENU button SCROLL button BAND button MD P button MD p button MD + button @¡ CD P button !º CD p button !¡ LOOP button !™ CD + button @™ !£...
  • Page 7 – 7 –...

  • Page 8: Disassembly

    SECTION 3 DISASSEMBLY Note: Follow the disassembly procedure in the numerical order given. CASE 2 case 1 two screws (case 3 TP2) 1 two screws (case 3 TP2) FRONT PANEL/MD MECHANISM DECK SECTION 7 six screws (BVTT 3 × 6) 6 wire (flat type) (25 core) (CN820) 8 MD mechanism section...
  • Page 9 BACK PANEL, JACK BOARD 2 four screws (BVTP 3 × 10) 7 JACK board 3 screw (BVTP 3 × 8) 6 wire (flat type) (15 core) (CN401) 2 screw (BVTP 3 × 10) 8 connector (CN402) 1 connector (CN590) 5 back panel 4 five claws MD MECHANISM DECK (MDM-3D) bracket (MD)
  • Page 10 CD MECHANISM DECK (CDM13C-5BD19) 3 two screws (BVTP 3 × 6) 7 CD mechanism deck (CDM13C-5BD19) 4 bracket (CD) 6 two hooks 5 two screws (BVTP 3 × 8) 3 two screws (BVTP 3 × 6) 2 connector 1 wire (flat type) (19 core) (CN291) (CN801) BD (MD) BOARD...
  • Page 11 DISC TABLE 2 holder (MG) ass'y 1 screw (BV 3 × 8) 1 screw (BV 3 × 8) 3 Pull the disc table SUB CHASSIS 1 two step screws 1 two step screws 2 two insulators 2 two insulators part A part A part A 3 sub chassis...
  • Page 12 OPTICAL PICK-UP (KSS-213B/K-N) 4 Remove the optical pick-up (KSS-213B/K-N) In the direction of the arrow C . 3 wire (flat type) (16 core) (CNU101) 1 Move the claw in the direction of the arrow A . 2 Remove the sled shaft in the direction of the arrow B .
  • Page 13 SLIDER COMPLETE ASS’Y claw 3 Set the shaft of gear (LB) to be at the position in the figure. claw 45° 1 special screw 2 retainer (gear) 4 Remove the slider complete ass’y (M 1.7 × 1.4) in the direction of arrow with putting out of two claws.
  • Page 14 SHUTTER ASS’Y 1 stopper washer 2 shaft (shutter) A shutter ass’y shaft (shutter) B 3 shutter ass’y shaft (shutter) A hole B hole A When installing, install the shaft (shutter) A into the hole as show in the figune before in- stalling the shaft (shutter) B into the hole B.

  • Page 15: Test Mode

    SECTION 4 TEST MODE 4-1. PRECAUTIONS FOR USE OF TEST MODE 4-5. SELECTING THE TEST MODE 1. As loading related operations will be performed regardless of Thirteen test modes are selected by turn VOLUME. the test mode operations being performed, be sure to check that Table 4-2.
  • Page 16 4-7. OPERATING THE CONTINUOUS RECORDING 4-6. OPERATING THE CONTINUOUS PLAYBACK MODE MODE 4-7-1. Entering the Continuous Recording Mode 4-6-1. Entering the Continuous Playback Mode 1. Set the MO disc in the unit. (Refer to note 3.) 1. Set the disc in the unit. (Whichever recordable discs or discs for 2.
  • Page 17 4-9. ERROR HISTORY MODE 4-9-5. Ending the displayed historys 1. Press the MD-CD CYNC button, the display will change to 4-9-1. Entering the Error History Mode memory types. 1. Turn the VOLUME knob and display “ERR DP MODE”. Table 4-4 2.
  • Page 18 4-10. FUNCTIONS OF OTHER BUTTONS 1. MODE display Displays “TEMP ADJUST”, “CPLAY MODE”, etc.. Table 4-3. 2. Error rate display Button Contents Error rates are displayed as follows. Turns recording on/off when pressed during r REC continuous playback. C1= : Indicates C1 error §...

  • Page 19: Md Section

    SECTION 5 ELECTRICAL ADJUSTMENT 5-3. PRECAUTIONS FOR ADJUSTMENTS MD SECTION 1) When replacing the following parts, perform the adjustments and checks with ® in the order shown in the following table. 5-1. PRECAUTIONS FOR CHECKING LASER DI- ODE EMISSION Table 5-1 To check the emission of the laser diode during adjustments, never view directly from the top as this may lose your eyesight.
  • Page 20 5-5. TEMPERATURE COMPENSATION OFFSET 5-6. LASER POWER ADJUSTMENT ADJUSTMENT Connection: laser Save the temperature data at that time in the non-volatile memory power meter as 25 °C reference data. Notes: 1. Usually, do not perform this adjustment. Optical pick-up 2. Perform this adjustment in an ambient temperature of 22 °C to objective lens 28 °C.
  • Page 21 5-7. TRAVERSE (E-F BALANCE) ADJUSTMENT 8. Turn the VOLUME knob so that the waveforms of the oscillo- scope becomes the specified value. (When the VOLUME knob Note 1: Data will be erased during MO reading if a recorded disc is used is turned, the “...
  • Page 22 5-8. FOCUS BIAS ADJUSTMENT 5-9. ERROR RATE CHECK Adjusting Method: 5-9-1. CD Error Rate Check 1. Load a continuously recorded disc (Refer to “5-4. Creating MO Checking Method: Continuously Recorded Disc”.). 1. Load a test disc TDYS-1. 2. Turn the VOLUME knob and display “CPLAY MODE”. 2.
  • Page 23 5-1. ADJUSTING POINTS AND CONNECTING POINTS [BD BOARD] (SIDE A) D101 IC192 [BD BOARD] (SIDE B) TP (IOP) TP (I + 3V) Q163 IC316 IC171 (VC) IC101 (TEO) Q102 IC121 – 23 –...

  • Page 24: Cd Section

    5. Confirm that the oscilloscope waveform (S-curve) is symmetri- CD SECTION cal between A and B. And confirm peak to peak level within 2.4 ± 0.7 Vp-p. Notes: 1. CD Block basically constructed to operated without adjustment. S-curve waveform symmetry Therefore, check eaech item in order given.
  • Page 25 Traverse waveform level: 300 ± 100 mVp-p × 100 = less than ± 7% specified value: • 2 (A+B) • A+B = 300 ± 100 mVp-p 7. After check, remove the lead wire connected in step 1. Focus/Tracking Gain Adjustment (RV102, RV103) This gain has a margin, so even if it is slightly off.
  • Page 26 SECTION 6 DIAGRAMS • Circuit Boards Location POWER AMP board AUDIO board MAIN board MD-LED board ENCAPSULATED COMPONENT (Malaysia, Singapore, HongKong) TUNER (FM/MW/LW) (AEP, UK, German, North European) PANEL board TRANSFORMER board JACK board ST TRANSLATION board SW board BD (MD) board BD (CD) board LOADING board –...
  • Page 27 IC101 (2/2) M102 SLED MOTOR • SLED MOTOR DRIVE OUT-SW S291 (LOAD OUT) M101 SPINDLE MOTOR SPINDLE • DRIVE MOTOR IN-SW S292 (LOAD IN) • SIGNAL PATH :digital out (CD) HCD-MD313 (1/3) CD Section – 27 – – 28 –...
  • Page 28 PACK OUT PB P SFDR SLED+ M902 REC P DRIVER SLED– SRDR SLED MOTOR SPDL+ SPRD M901 M903 (MD) LOAD-IN DRIVER SPDL– SPFD SPINDLE MOTOR LOADING MOTOR LOAD-OUT XRST XRST HCD-MD313 (2/3) MD Section – 29 – – 30 –...
  • Page 29 CP POWER G : German SP : Singapore IC603 CD+5V MY : Malaysia HK : Hong Kong Q561, 562 AED : North European POWER ON/OFF SW X302 HCD-MD313 (3/3) Q571, 572 7 MHz MAIN Section – 32 – – 31 –...
  • Page 30 • Waveforms – CD Section – – MD Section – 1 IC101 #¡ (RFO) (PLAY Mode) 6 IC103 @∞ (XPCK) 1 IC101 1, 2 (I, J) (PLAY Mode) 500 mV/DIV, 500 ns/DIV Approx. 1.3 ± 0.3 Vp-p 5.3 Vp-p 500 mVp-p 14 ns 2 IC101 $¢...
  • Page 31 6 IC152 #¡ (CAPA+) (Play Mode) !¡ IC121 @¶ (FS256) 4.6 Vp-p 3.4 Vp-p 11.2896 MHz 1.5 µ sec 7 IC121 (º (FS4) – MAIN Section – 1 IC601 !¡ (XI) 3.4 Vp-p 4.3 Vp-p 5.7 µ sec 5 MHz 8 IC121 !§...

  • Page 32: Ic Block Diagrams

    • IC Block Diagrams – CD Section – IC101 CXA1782BQ – LEVELS 24 SENS – MIRR RF IV AMP1 DFCT 23 C. OUT – 22 XRST RF IV AMP2 21 DATA FE BIAS • IIL DATA RESISTOR • INPUT SHIFT RESISTOR •...
  • Page 33 IC102 BA6397FP DRIVE DRIVE DRIVE BUFFER BUFFER BUFFER DRIVE BUFFER REGULATOR DRIVER MUTE DRIVE DRIVE DRIVE DRIVE BUFFER BUFFER BUFFER BUFFER IC103 CXD2507AQ SERVO AUTO DATA SEQUENCER XRST SENS SUB CODE MUTE INTERFACE PROCESSOR DIGITAL LOCK SQCK TEST SQSO FILO EXCK DIGITAL FILI...
  • Page 34 IC104 PCM1710U-B LRCIN ML/DSD INPUT MC/DM2 INTERFACE DIGITAL MODE FILTER CONTROL BCKIN MD/DM1 TIMING CLKO MUTE CONTROL MODE CKSL NOISE SHAPER DGND DGND 5-LEVEL DAC 5-LEVEL DAC RIGHT LEFT GND2R GND2L LOW-PASS FILTER LOW-PASS FILTER RIGHT LEFT EXT1R EXT1L 3-STAGE AMP 3-STAGE AMP EXT2R EXT2L...
  • Page 35 IC101 CXA2523AR 43 42 USROP – RF AGC – USRC RFA1 BPF3T RFA2 PEAK3T – HLPT –1 – – –2 – CFST PTGR TEMP PEAK – –2 – 36 BOTM BOTTOM – –1 GRVA 35 ABCD 34 FE 33 AUX –...
  • Page 36 IC121 CXD2652AR 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 AUX2 SPINDLE GENERATOR SERVO 74 TE MNT0 73 SE MNT1 MONITOR EACH 72 AVSS CONTROL BLOCK...

  • Page 37: Main Section

    – MAIN Section – IC603 M62016L IC570 LA5620 INTERRUPT SIGNAL – GENERATING BLOCK – RESET SIGNAL – GENERATING BLOCK STBY RESET ANA5 – SYS3.3 – – 3.3V BACK – DELAY CIRCUIT P. DOWN – DELAY CIRCUIT VREF S. RESET – 72 –...

  • Page 38: Audio Section

    IC801 LB1641 T.S.D O.C.P MOTOR MOTOR DRIVE DRIVE FWD/REV/STOP CONTROL LOGIC – AUDIO Section – IC1500 BU1922F TEST LOGIC AND OUTPUT SELECTOR SWITCH 57kHz OSCILLATOR ANTI- QUALITY BIT RECONSTRUCTION BANDPASS ALIASING GENERATOR FILTER (8th ORDER) DIVIDER FILTER BIPHASE CONTAS LOOP DEFFERENTIAL CLOCKED SYMBOL...

  • Page 39: Ic Pin Function Description

    6-12. IC PIN FUNCTION DESCRIPTION • BD (MD) BOARD IC101 CXA2523AR (RF AMPLIFIER) Pin No. Pin Name Function I-V converted RF signal I input from the optical pick-up block detector I-V converted RF signal J input from the optical pick-up block detector Middle point voltage (+1.65V) generation output terminal 4 to 9 A to F...
  • Page 40 • BD (MD) BOARD IC121 CXD2652AR • (DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO PROCESSOR, EFM/ACIRC ENCODER/DECODER, SHOCK • PROOF MEMORY CONTROLLER, ATRAC ENCODER/DECODER, 2M BIT D-RAM) Pin No. Pin Name Function MNT0 (FOK) Focus OK signal output to the MD system controller (IC316) “H” is output when focus is on MNT1 (SHCK) Track jump detection signal output to the MD system controller (IC316) MNT2 (XBUSY)
  • Page 41 Pin No. Pin Name Function DVSS — Ground terminal (digital system) Output enable signal output to the external D-RAM (IC124) XCAS Column address strobe signal output to the external D-RAM (IC124) Address signal output to the external D-RAM (IC124) XRAS Row address strobe signal output to the external D-RAM (IC124) Write enable signal output to the external D-RAM (IC124) Two-way data bus for the external D-RAM (IC124)
  • Page 42 Pin No. Pin Name Function APCREF Control signal output to the reference voltage generator circuit for the laser automatic power control LDDR PWM signal output for the laser automatic power control Not used (open) TRDR Tracking servo drive PWM signal (–) output to the BH6511FS (IC152) TFDR Tracking servo drive PWM signal (+) output to the BH6511FS (IC152) DVDD...
  • Page 43 • BD (MD) BOARD IC316 M30610MC-109FP (MD SYSTEM CONTROL) Pin No. Pin Name Function (JOG0, JOG1) Encoder switch signal input terminal Not used (fixed at “H”) DAOUT1, DAOUT2 Not used (fixed at “L”) SQSY Subcode Q sync (SCOR) input from the CXD2652AR (IC121) REMCON Remote control signal input De-emphasis control signal output to the AK4520 (IC201)
  • Page 44 Pin No. Pin Name Function HF module ON signal output terminal LDIN MD loading-in signal output to LB1830M (IC153) LDOUT MD loading-out signal output to LAB1830M (IC153) LD-LOW Loading motor voltage control signal output to the loading motor driver PROTECT MD PROTECT switch (S683) detect signal input terminal REFLECT MD REFLECT switch (S682) detect signal input terminal...
  • Page 45 • MAIN BOARD (1/3) IC601 µPD78078GF-062-3BA (MASTER CONTROL) Pin No. Pin Name Function 1 to 3 Destination setting terminal Destination setting terminal Not used (open) 5 to 7 (NC) — Not used (NC) — Not used (open) — Connecting to ground Main system clock output terminal (5 MHz) Main system clock input terminal (5 MHz) —...
  • Page 46 Pin No. Pin Name Function BD DATA Serial data output to the CXD2507AQ (IC103) Serial data latch pulse signal output to the CXD2507AQ (IC103) PRGL (DF. LAT) Serial data latch pulse signal output to the PCM1710U (IC104) SENCE Internal status (SENSE) signal input from the CXD2507AQ (IC103) Test mode input terminal “H’: normal (fixed at “H”...

  • Page 47: Exploded Views

    A-4403-402-A PANEL BOARD, COMPLETE 4-993-863-11 WINDOW (M3) (AEP, UK, G, AED) 1-782-793-11 WIRE (FLAT TYPE) (23 CORE) X-4948-965-1 PANEL ASSY, FRONT 4-993-851-01 PANEL (CD), LOADING 4-962-708-01 EMBLEM (4-A), SONY 3-363-099-11 SCREW (CASE 3 TP2) 4-930-336-71 FOOT (FELT) * 13 4-993-842-01 CASE 4-993-845-01 CUSHION –...
  • Page 48 (2) CHASSIS SECTION not supplied supplied MD MECHANISM DECK SECTION FAN901 T1600 supplied supplied supplied supplied CD MECHANISM DECK SECTION (including r A, r B) EXCEPT MY, SP not supplied CNP1601 CNP1601 The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.
  • Page 49 (3) MD MECHANISM DECK SECTION-1 (MDM-3D) not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * 101 A-4699-808-A BD (MD) BOARD, COMPLETE 4-986-959-01 WASHER, STOPPER 1-660-966-11 OP RELAY FLEXIBLE BOARD 4-987-327-01 INSULATOR 1-782-683-11 WIRE (FLAT TYPE) (14 CORE) 4-628-167-01 SCREW, STEP X-4948-722-1 SHUTTER ASSY 4-987-910-01 SPRING (O/C), TENSION...
  • Page 50 (4) MD MECHANISM DECK SECTION-2 (MDM-3D) not supplied not supplied M902 M903 M901 HR901 The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Ref. No. Part No. Description Remark Ref.
  • Page 51 (5) CD MECHANISM DECK SECTION-1 (CDM13C-5BD19) not supplied M903 not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * 201 1-634-461-11 LOADING BOARD 4-944-012-01 TABLE, DISC 4-927-654-01 WASHER (LIMITER) A-4604-752-A HOLDER (MG) ASSY 3-659-338-00 SPRING, COMPRESSION * 223 4-917-583-21 BRACKET, YOKE 4-929-764-01 SHAFT (TABLE GUIDE)
  • Page 52 (6) CD MECHANISM DECK SECTION-2 (CDM13C-5BD19) M102 M101 (including r C) The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Ref. No. Part No. Description Remark Ref. No. Part No.

  • Page 53: Electrical Parts List

    SECTION 8 AUDIO ELECTRICAL PARTS LIST NOTE: The components identified by mark • Due to standardization, replacements in the • Items marked “*” are not stocked since they ! or dotted line with mark ! are parts list may be different from the parts speci- are seldom required for routine service.
  • Page 54 AUDIO BD (CD) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < TRANSISTOR > < VIBRATOR > Q701 8-729-119-78 TRANSISTOR 2SC403SP-51 X1501 1-579-900-21 VIBRATOR, CRYSTAL (4.332MHz) Q702 8-729-141-30 TRANSISTOR 2SC3623A-LK (AEP, UK, G, AED) Q703 8-729-422-57 TRANSISTOR UN4111 ************************************************************* Q751 8-729-119-78 TRANSISTOR 2SC403SP-51...
  • Page 55 BD (CD) BD (MD) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R147 1-216-049-11 METAL GLAZE 1/10W CNU101 1-770-014-11 CONNECTOR, FFC/FPC 16P R148 1-216-049-11 METAL GLAZE 1/10W CNU102 1-770-013-11 CONNECTOR, FFC/FPC 19P R149 1-216-049-11 METAL GLAZE 1/10W <...
  • Page 56 BD (MD) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C2001 1-163-038-00 CERAMIC CHIP 0.1uF C135 1-163-038-00 CERAMIC CHIP 0.1uF C2002 1-163-038-00 CERAMIC CHIP 0.1uF C136 1-126-206-11 ELECT CHIP 100uF 6.3V C139 1-163-235-11 CERAMIC CHIP 22PF C2003 1-163-038-00 CERAMIC CHIP 0.1uF...
  • Page 57 BD (MD) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark Q181 8-729-018-75 TRANSISTOR 2SJ278MY Q182 8-729-017-65 TRANSISTOR 2SK1764KY R198 1-216-295-11 CONDUCTOR, CHIP (2012) Q350 8-729-028-99 TRANSISTOR RT1N144M-TP-1 R199 1-216-295-11 CONDUCTOR, CHIP (2012) R200 1-216-295-11 CONDUCTOR, CHIP (2012) <...
  • Page 58 BD (MD) JACK Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R449 1-216-097-00 METAL GLAZE 100K 1/10W < DIODE > R451 1-216-097-00 METAL GLAZE 100K 1/10W R454 1-216-097-00 METAL GLAZE 100K 1/10W D422 8-719-987-63 DIODE 1N4148M D430 8-719-987-63 DIODE 1N4148M R455...
  • Page 59 JACK LOADING MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R452 1-249-441-11 CARBON 100K 1/4W C550 1-117-850-11 ELECT (SOLID) 15000uF R453 1-249-425-11 CARBON 4.7K 1/4W C551 1-136-165-00 FILM 0.1uF R454 1-249-425-11 CARBON 4.7K 1/4W C552 1-136-165-00 FILM 0.1uF R455...
  • Page 60 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < CONNECTOR > IC601 8-759-480-96 IC uPD78078GF-062-3BA CN503 1-564-511-11 PLUG, CONNECTOR 8P IC602 8-759-635-63 IC M51943BSL CN506 1-770-412-11 CONNECTOR, BOARD TO BOARD 6P IC603 8-759-481-02 IC M62016L CN590 1-564-506-11 PLUG, CONNECTOR 3P IC801...
  • Page 61 MAIN MD-LED PANEL Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R610 1-247-807-31 CARBON 1/4W R871 1-249-421-11 CARBON 2.2K 1/4W R611 1-249-429-11 CARBON 1/4W R872 1-249-441-11 CARBON 100K 1/4W R612 1-247-807-31 CARBON 1/4W R613 1-247-807-31 CARBON 1/4W R873 1-247-887-00 CARBON...
  • Page 62 PANEL POWER AMP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < DIODE > R928 1-249-411-11 CARBON 1/4W R929 1-249-437-11 CARBON 1/4W D901 8-719-010-43 DIODE UZ-5.6BSC R930 1-249-411-11 CARBON 1/4W D902 8-719-058-03 LED SEL5423E-TP15 (( (MD)) R931 1-249-437-11 CARBON 1/4W11...
  • Page 63 POWER AMP ST TRANSLATION TRANSFORMER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C1208 1-126-965-11 ELECT 22uF R1229 1-249-429-11 CARBON 1/4W C1210 1-136-163-00 FILM 0.068uF C1211 1-136-163-00 FILM 0.068uF R1231 1-247-807-31 CARBON 1/4W R1232 1-249-429-11 CARBON 1/4W C1220 1-126-924-11 ELECT...
  • Page 64 TRANSFORMER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * CN1601 1-564-518-11 PLUG, CONNECTOR 3P ************** CN1602 1-564-523-11 PLUG, CONNECTOR 8P HARDWARE LIST ************** < FUSE > 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S ! F1601 1-532-464-31 FUSE (T2.5AL/250V) (MY, SP, HK) 7-685-647-79 SCREW +BVTP 3X10 TYPE2 N-S ! F1603 1-532-504-31 FUSE (T4AL/250V)

Table of Contents