Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Honeywell PRO TH3110B
Summary of Contents for Honeywell PRO TH3110B
-
Page 1: Installation Guide
Installation Guide TH3110B Non-programmable Digital Thermostat... -
Page 2: Power Type
If this product is replacing a control that contains mercury in a sealed tube, do not place the old control in the trash. Contact your local waste management authority for instructions regarding recycling and proper disposal. ® U.S. Registered Trademark. Patents pending. Copyright © 2005 Honeywell International Inc. All rights reserved. -
Page 3: Table Of Contents
PRO TH3110B Non-programmable Digital Thermostat Table of contents I I n n s s t t a a l l l l a a t t i i o o n n A A p p p p e e n n d d i i c c e e s s Pre-installation checklist ....2... -
Page 4: Pre-Installation Checklist
Installation Guide Pre-installation checklist Package contents Check to make sure your package includes the following items: Operating manual PRO TH3110B digital thermostat (wallplate attached to back) Wall anchors and AA alkaline mounting screws batteries (2) (2 each) Required tools & supplies •... -
Page 5: Wallplate Installation
PRO TH3110B Non-programmable Digital Thermostat Wallplate installation Grasp top and bottom of wallplate Remove the wallplate from the ther- and pull to remove from thermostat. mostat as shown at left, then follow directions below for mounting. 1 Pull wires through wire hole. -
Page 6: Wiring
Installation Guide Wiring CAUTION: ELECTRICAL HAZARD. Can cause electrical shock or equipment damage. Disconnect power before wiring. Wiring Keep wires in this shaded area 1 Loosen screw terminals, insert wires into terminal block, then re- tighten screws. 2 Push excess wire back into the wall opening. -
Page 7: Wiring Diagrams
PRO TH3110B Non-programmable Digital Thermostat Wiring diagrams Power supply. Provide disconnect means and overload protection as required. Factory-installed jumper. Remove for 2-transformer systems only. Use either O or B terminals for changeover valve. Use a small piece of wire (not supplied) to connect W and Y terminals. -
Page 8: Fan Operation Settings
Installation Guide Fan operation settings • G G a a s s o o r r O O i i l l : : For gas or oil heating systems, leave the fan operation switch in this factory-set position (This setting is for systems that control the fan in a call for heat.) •... -
Page 9: Battery Installation
PRO TH3110B Non-programmable Digital Thermostat Battery installation Install two AA alkaline batteries in the back of the thermostat, as shown at left. Fresh batteries should be installed immediately when the warn- R R E E P P L L A A C C E E B B A A T T T T ing begins flashing (see page 10.) The... -
Page 10: Installer Setup
Installation Guide Installer setup Follow the procedure below to configure the thermostat to match the installed heating/cooling system, and customize feature operation as desired. Press and hold both buttons Function Setting number Setup To begin, press and hold the Press to change settings buttons until the display changes Press... -
Page 11: Installer System Test
PRO TH3110B Non-programmable Digital Thermostat Installer system test Follow the procedure below to test the heating and cooling system. System test System status number Test System switch 1 Set S S Y Y S S T T E E M M switch to Cool. -
Page 12: Quick Reference To Controls
Installation Guide Quick reference to controls Digital display screen Temperature buttons Press to adjust temperature settings System switch • Cool: Thermostat controls only the cooling system. • Heat: Thermostat controls only the heating system. Fan switch • Off: Heating and cooling On: Fan runs continuously. -
Page 13: In Case Of Difficulty
PRO TH3110B Non-programmable Digital Thermostat In case of difficulty If you have difficulty with your thermostat, please try the suggestions below. Most problems can be corrected quickly and easily. Display is blank • Make sure fresh AA alkaline batteries are correctly installed (see page 7). -
Page 14: Accessories
Installation Guide Accessories Please contact your distributor to order accessories. Cover plate assembly ..........Part Number 50002883-001 (Used to cover marks left by old thermostats.) Specifications Temperature Ranges Electrical Ratings • Heat: 40° to 90°F (4.5° to 32°C) • Cool: 50° to 99°F (10° to 37°C) System Voltage (50/60Hz) Running Current... - Page 16 Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Scarborough, Ontario M1V 4Z9 ® U.S. Registered Trademark. Patents pending. Copyright © 2005 Honeywell International Inc. All rights reserved. www.honeywell.com/yourhome Printed in U.S.A. Document number 69-1793. Date 01-2005.