Makita 1051D Instruction Manual
Cordless power planer
Hide thumbs
Also See for 1051D:
- Instruction manual (72 pages) ,
- Instruction manual (13 pages) ,
- Instruction manual (53 pages)
Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
Advertisement
Related Manuals for Makita 1051D
Summary of Contents for Makita 1051D
- Page 1 Cordless Power Planer INSTRUCTION MANUAL Ni-Cd 2.0Ah Ni-MH 2.6 Ah Ni-MH 3.0 Ah DWAE DWDE DWFE ...+ MODEL Extra 1051 D...
- Page 2 Planing width Planing depth 50 mm 0.5 mm (131B2") (0.02") Battery Cartridge Voltage 1422 14.4 V 1434 14.4 1435 14.4 V Manufacturer reserves the right to change specifications without notice. Note: Specifications may differ from country to country. WARNING: For your personal safety, READ and understand before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
-
Page 3: General Safety Rules
GENERAL SAFETY RULES All Battery Operated (For WARNING! Read and understand to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. - Page 4 Tool Use a n d Care Use clamps or other practical way t o secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead t o loss of control. not force tool.
- Page 5 16. Always change both blades or covers on the drum, otherwise the resulting imbalance will cause vibration and shorten tool life. Wait for complete run-down before putting the tool aside. Use only Makita blades specified in this manual. SAVE THESE INSTRUCTIONS. run for a while. Watch away from the tool at all times.
- Page 6 The followings show the symbols used for tool. __-- ..Jmin SYMBOLS volts direct current no load speed revolutions or reciprocation per minute...
- Page 7 IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE SAVE THESE INSTRUCTIONS Length of Cord (Feet) AWG Size of Cord 9. Do not operate charger with damaged cord or plug mediately. 10. Do not operate charger if wise damaged in any way; take it t o a qualified serviceman. Do not disassemble charger or battery cartridge;...
- Page 8 ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). 2. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. Do not allow anything t o cover or clog the charger vents.
-
Page 9: Functional Description
FUNCTIONAL DESCRIPTION Installing or removing battery cartridge *Always switch off the tool before inser- tion or removal of the battery cartridge. *To remove the battery cartridge, withdraw from the tool while pressing the buttons on both sides of the cartridge. *To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip... - Page 10 CAUTION: *The high capacity battery charger Model DC1411 is for charging Makita battery cartridge. Never use it for other purposes or for other manufacturer's batteries. *When you charge a new battery cartridge or a battery cartridge which has not been used...
- Page 11 Adjusting depth The depth cut can be adjusted in 0.1 mm increments within a range Turn the knob on the front of the tool until the pointer (0.02"). cutting depth on the scale. CAUTION: The knob can be turned beyond the 0.5 mm the tool with a depth of cut more than 0.5 mm (0.02").
- Page 12 Edge fence (Guide rule) Use the edge fence when shiplapping (rab- beting) or cutting workpieces nearly (1-31/32") wide. Install the edge fence on the tool and secure it with the washer and thumb screw (A). .Loosen the thumb screw (B) and adjust the edge fence until in contact with the side of the workpiece.
- Page 13 Shiplapping (Rabbeting) To make a stepped cut as shown in Fig., use the edge fence (guide rule). Draw a cutting line on the workpiece. Align the blade edge with the cutting line. Then adjust the edge fence as explained in the "Edge fence"...
- Page 14 For the best results, empty the dust bag when it becomes about half full. Remove the dust bag from the tool and pull out the fastener. NOTE: If you connect a Makita vacuum cleaner Model 406 to this tool, more efficient and cleaner operations can be performed. Removing or installing planer blades...
- Page 15 CAUTION: Use only the Makita hex wrench provided to remove or install the blades. Failure to do so may result in overtightening or insufficient tightening of the installation bolts. This could cause an injury.
-
Page 16: Operation
Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILIW, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Recycling the Battery... - Page 17 ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories The accessories or attachments should be used only in the proper and intended manner. High Capacity Battery charger...
- Page 18 Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, one of Makita's Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option. replace) without charge. This Warranty does not apply where:...